Loading...
HomeMy WebLinkAboutD1.1 DEMOLITION PLANS.pdfProject Number: Sheet Title: Issue Date: Sheet Number: Project: CA R M E L , I N D I A N A 4 6 0 3 2 By: Architect: Architecture / Project Management: Carmel, Indiana 46032 317.705.7980 (fax) 355 City Center Drive 317.705.7979 (phone) Drawn By Checked ByPrint Date Revisions: 76 0 3 R D A V E N U E S . W . PE D C O R S Q U A R E B U I L D I N G 2 KE L L E R MA C A L U S O , L L C N D1.1 DEMOLITION PLANS PEDCOR DESIGN GROUP, LLC 12/23/13 CONSTRUCTION DOCUMENTS THIS DOCUMENT IS AN INSTRUMENT OF SERVICE AND IS THE SOLE PROPERTY OF THE ARCHITECT AND PEDCOR DESIGN GROUP, LLC. ALLINFORMATION CONTAINED HEREIN IS CONFIDENTIAL. ITS SUBMISSION AND DISTRIBUTION TO OTHER PARTIES IS NOT TO BE CONSTRUED ASPUBLICATION IN DEROGATION OF COMMON LAW COPYRIGHT, INTELLECTUAL PROPERTY RIGHTS OR OTHER RESERVED RIGHTS. ALLINFORMATION CONTAINED HEREIN CONSTITUTES THE ORIGINAL AND UNPUBLISHED WORK OF THE ARCHITECT, JAMES R. STUTZMAN, ANDPEDCOR DESIGN GROUP, LLC. NO PART OR WHOLE OF THIS DESIGN,THESE DRAWINGS, OR THE RESULTING BUILDING OR BUILDINGS, ORPORTIONS OF THE RESULTING BUILDING OR BUILDINGS MAY BEDUPLICATED, COPIED, EXHIBITED, PHOTOGRAPHED, PUBLISHED,MODIFIED OR OTHERWISE DISTRIBUTED IN ANY WAY WITHOUT THESPECIFIC AND PRIOR WRITTEN CONSENT OF THE ARCHITECT, JAMES R.STUTZMAN AND PEDCOR DESIGN GROUP, LLC.© COPYRIGHT 2012, JAMES R. STUTZMAN, AIA, CARMEL. 12/23/13 STATE RELEASE SET MC AJR KEY PLAN SCALE: N.T.S. SECOND FLOOR T FEC DP2 PU L L DP6 DP1 DP2 DP2 DP2 DP1 DP1 DP1 DP1 DP1 DP1 DP1 DP3 DP4DP4 DP4 DP4 DP4 DP4 DP4 DP4 DP4 DP4 DP4 DP4 DP4 DP4 DP5 DP5 DP5 DP5 DP7 DP2 DP8 DP9 DP4 DP4 1. DEMOLITION LEGEND:GENERAL DEMOLITION NOTES: REMOVE ALL WALLS, MILLWORK, DOORS AND DOOR FRAMES AS SHOWN DASHED. RESERVE DOORS AND DOOR FRAMES FOR RE-USE IN NEW PROJECT SCOPE. 2. 3. SAVE ALL ITEMS REMOVED FROM THE SPACE PER OWNER'S DIRECTION UNLESS NOTED OTHERWISE. EXISTING CONSTRUCTION TO BE REMOVED. EXISTING PARTITION TO REMAIN. DEMOLITION PLAN NOTES REMOVE DOOR/FRAME AND SAVE FOR REUSE. REMOVE SECTION OF WALL AND PREP FOR NEW CONSTRUCTION. REMOVE EXISTING SINK AND COUNTER TOP. DP1 DP2 DP3 DP4 DP5 DP6 DP7 DP8 REMOVE EXISTING FLOORCOVERING FROM THIS AREA AND PREP FOR NEW FLOORING. DUPLEX WALL OUTLET TO BE REMOVED. PHONE/DATA WALL OUTLET TO BE REMOVED. T DP9 THERMOSTAT TO BE REMOVED. REMOVE ALL EXISTING BLINDS AT PERIMETER WINDOW LIGHT LOCATIONS. SAVE BLINDS FOR OWNER'S REUSE. 5. 4.DEMOLISH DENOTED EXISTING CEILING SYSTEM CLEARLY AND CLEANLY BACK TO A POINT WHERE INSTALLATION OF NEW CEILING SYSTEM IS POSSIBLE. SEE CEILING DEMOLITION PLAN FOR EXTENT OF WORK. DEMOLISH EXISTING WALL AND/OR FLOOR SURFACES BACK TO A POINT WHERE INSTALLATION OF NEW FLOORING FINISHES IS POSSIBLE. 6. 7. REMOVE EXISTING FINISHES WHERE NEW FINISHES ARE TO BE INSTALLED. REFERENCE FINISH PLAN TO COORDINATE LOCATION OF NEW FINISHES. REMOVE ELECTRICAL AND DEVICE LINES IN WALLS THAT ARE TO BE REMOVED, INCLUDING ALL ATTACHED WIRING. DEMOLISH ELECTRICAL DEVICES AND WIRING BACK TO A POINT WHEREAS PROPER PREPERATION FOR NEW FINISHES IS POSSIBLE. SEE ELECTRICAL AND FINISH PLANS FOR FURTHER INFORMATION. 8.ALL DEMOLISHED RECEPTICLES FROM EXISTING WALLS TO REMAIN SHALL HAVE DRYWALL PATCHED AND REPAIRED PRIOR TO INSTALLATION OF WALL FINISHES. DP10 DP11 REMOVE ELECTRICAL/DATA/TV OUTLETS/SWITCHES INCLUDING ALL ATTACHED WIRING BACK TO THE MAIN PANEL. PATCH WALL AT REMOVED DEVICE LOCATION.LIGHT FIXTURE TO BE REMOVED. EXIT SIGN TO BE REMOVED. LIGHT SWITCH TO BE REMOVED. EMERGENCY LIGHTING TO BE REMOVED. CEILING TILE AND GRID TO BE REMOVED. DP12 DP13 DP14 REMOVE HORN-STROBE AND/OR FIRE PULL. PATCH WALL AT REMOVED DEVICE LOCATION. 9.REMOVE ALL EXISTING FLOOR OUTLETS SHOWN. PROVIDE AN EVEN FLOOR SURFACE IN PREPARATION FOR NEW FLOOR FINISH. DP15 REMOVE LIGHT FIXTURES SHOWN ON THE PLAN. SAVE LIGHT FIXTURES FOR REUSE. REMOVE EXISTING FIRE EXTINGUISHER CABINET. SAVE FOR REUSE. PATCH WALL AND PREP FOR NEW FINISH.PULL HORN/STROBE AND PULL STATION TO BE REMOVED. REMOVE CROWN MOLDING. SAVE FOR REUSE. REMOVE EXISTING WINDOW AND PREP FOR NEW CONSTRUCTION. RELOCATE EXISTING THERMOSTAT. SEE ELECTRICAL/DATA PLAN FOR NEW LOCATION. REMOVE EXISTING CEILING TILE, GRID, AND LIGHTING IN SHADED AREA AND SAVE FOR REUSE. INSTALL NEW TILE AND GRID AS SHOWN ON THE REFLECTED CEILING PLAN. REUSE DEMO'D TILE AS MUCH AS POSSIBLE. REMOVE SWITCHES AND ASSOCIATED WIRING. REMOVE EMERGENCY LIGHTING. SAVE FOR REUSE. REMOVE EXIT SIGNS. SAVE FOR REUSE. LIGHT FIXTURE TO BE REMOVED. DENOTES AREA NOT IN CONTRACT. DP11 DP12 DP13 DP10 DP12 DP10 DP10 DP10 DP10 DP10 DP11 DP11 DP11 DP11 DP11 DP12 DP12 DP14 DP15 DP12 SCALE: 1/8" = 1'-0" 1 DEMOLITION PLAN D1.1 SCALE: 1/8" = 1'-0" 2 DEMOLITION CEILING PLAN D1.1