Loading...
HomeMy WebLinkAbout074213 METAL COMPOSITE MATERIAL WALL PANELS.pdf Giant Eagle Market #6550 The Bridges, Carmel, Indiana Building Shell Bid & Permit DLA Project 2014040.00 August 12, 2014 METAL COMPOSITE MATERIAL WALL PANELS 074213 - 1 SECTION 074213.23 - METAL COMPOSITE MATERIAL WALL PANELS PART 1 - GENERAL 1.1 SUMMARY A. Section includes metal composite material wall panels. 1.2 ACTION SUBMITTALS A. Product Data: For each type of product. B. Shop Drawings: Include fabrication and installation layouts of metal composite material panels; details of edge conditions, joints, panel profiles, corners, anchorages, attachment assembly, trim, flashings, closures, and accessories; and special details. C. Samples: For each type of metal composite material panel indicated. 1.3 INFORMATIONAL SUBMITTALS A. Product test reports. B. Warranties: Samples of special warranties. 1.4 CLOSEOUT SUBMITTALS A. Maintenance data. 1.5 QUALITY ASSURANCE A. Installer Qualifications: An entity that employs installers and supervisors who are trained and approved by manufacturer. 1.6 WARRANTY A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace components of metal composite material panel systems that fail in materials or workmanship within specified warranty period. 1. Warranty Period: Two years from date of Substantial Completion. Giant Eagle Market #6550 The Bridges, Carmel, Indiana Building Shell Bid & Permit DLA Project 2014040.00 August 12, 2014 METAL COMPOSITE MATERIAL WALL PANELS 074213 - 2 B. Special Warranty on Panel Finishes: Manufacturer's standard form in which manufacturer agrees to repair finish or replace metal composite material panels that show evidence of deterioration of factory-applied finishes within specified warranty period. 1. Finish Warranty Period: 20 years from date of Substantial Completion. PART 2 - PRODUCTS 2.1 PERFORMANCE REQUIREMENTS A. Structural Performance: Provide metal composite material panel systems capable of withstanding the effects of the following loads, based on testing according to ASTM E 330: 1. Wind Loads: As indicated on Drawings. 2. Deflection Limits: For wind loads, no greater than 1/180 of the span. 3. Test-Pressure Difference: 1.57 lbf/sq. ft. B. Water Penetration under Static Pressure: No water penetration when tested according to ASTM E 331 at the following test-pressure difference: 1. Test-Pressure Difference: 2.86 lbf/sq. ft. C. Thermal Movements: Allow for thermal movements from ambient and surface temperature changes by preventing buckling, opening of joints, overstressing of components, failure of joint sealants, failure of connections, and other detrimental effects. Base calculations on surface temperatures of materials due to both solar heat gain and nighttime-sky heat loss. 1. Temperature Change (Range): 120 deg F, ambient; 180 deg F, material surfaces. D. Fire-Resistance Ratings: Comply with ASTM E 119; testing by a qualified testing agency. Identify products with appropriate markings of applicable testing agency. 1. Indicate design designations from UL's "Fire Resistance Directory" or from the listings of another qualified testing agency. E. Fire Propagation Characteristics: Metal composite material wall panel system passes NFPA 285 testing. 2.2 METAL COMPOSITE MATERIAL WALL PANELS A. Metal Composite Material Wall Panel Systems: Provide factory-formed and -assembled, metal composite material wall panels fabricated from two metal facings that are bonded to a solid, extruded thermoplastic core; formed into profile for installation method indicated. Include attachment assemblies components, panel stiffeners, and accessories required for weathertight system. Giant Eagle Market #6550 The Bridges, Carmel, Indiana Building Shell Bid & Permit DLA Project 2014040.00 August 12, 2014 METAL COMPOSITE MATERIAL WALL PANELS 074213 - 3 1. Provide products by one of the following: a. Firestone Series 1000 (Basis of design) b. Pac-Clad by Petersen Aluminum c. Centria d. 3A Composites Alucobond e. Approved equivalent B. Aluminum-Faced Composite Wall Panels: Formed with 0.020-inch-thick, coil-coated aluminum sheet facings. 1. Panel Thickness: 4mm. 2. Core: Standard. 3. Exterior Finish: Two-coat fluoropolymer. a. Color: As indicated. C. Attachment Assembly Components: Formed from extruded aluminum. D. Attachment Assembly: Manufacturer's standard. 2.3 MISCELLANEOUS MATERIALS A. Miscellaneous Metal Subframing and Furring: ASTM C 645, cold-formed, metallic-coated steel sheet ASTM A 653/A 653M, G90 (Z275 hot-dip galvanized) coating designation or ASTM A 792/A 792M, Class AZ50 (Class AZM150) aluminum-zinc-alloy coating designation unless otherwise indicated. Provide manufacturer's standard sections as required for support and alignment of metal composite material panel system. B. Panel Accessories: Provide components required for a complete, weathertight panel system including trim, copings, fasciae, mullions, sills, corner units, clips, flashings, sealants, gaskets, fillers, closure strips, and similar items. Match material and finish of metal composite material panels unless otherwise indicated. C. Flashing and Trim: Provide flashing and trim formed from same material as metal composite material panels as required to seal against weather and to provide finished appearance. Locations include, but are not limited to, bases, drips, sills, jambs, corners, endwalls, framed openings, soffits, reveals, and fillers. Finish flashing and trim with same finish system as adjacent metal composite material panels. D. Panel Fasteners: Self-tapping screws designed to withstand design loads. Provide exposed fasteners with heads matching color of metal composite material panels by means of plastic caps or factory-applied coating. Provide EPDM or PVC sealing washers for exposed fasteners. E. Panel Sealants: ASTM C 920; as recommended in writing by metal composite material panel manufacturer. Provide sealant types recommended by manufacturer that are compatible with panel materials, are non-staining, and do not damage panel finish. Giant Eagle Market #6550 The Bridges, Carmel, Indiana Building Shell Bid & Permit DLA Project 2014040.00 August 12, 2014 METAL COMPOSITE MATERIAL WALL PANELS 074213 - 4 2.4 FABRICATION A. General: Fabricate and finish metal composite material panels and accessories at the factory, by manufacturer's standard procedures and processes, as necessary to fulfill indicated performance requirements demonstrated by laboratory testing. Comply with indicated profiles and with dimensional and structural requirements. B. Fabricate metal composite material panel joints with factory-installed captive gaskets or separator strips that provide a weathertight seal and prevent metal-to-metal contact, and that minimize noise from movements. C. Sheet Metal Flashing and Trim: Fabricate flashing and trim to comply with manufacturer's recommendations and recommendations in SMACNA's "Architectural Sheet Metal Manual" that apply to design, dimensions, metal, and other characteristics of item indicated. 2.5 FINISHES A. Panels and Accessories: 1. Two-Coat Fluoropolymer: AAMA 2605. Fluoropolymer finish containing not less than 70 percent PVDF resin by weight in color coat. Prepare, pretreat, and apply coating to exposed metal surfaces to comply with coating and resin manufacturers' written instructions. PART 3 - EXECUTION 3.1 PREPARATION A. Miscellaneous Supports: Install subframing, furring, and other miscellaneous panel support members and anchorages according to ASTM C 754 and metal composite material panel manufacturer's written recommendations. 3.2 METAL COMPOSITE MATERIAL PANEL INSTALLATION A. Attachment Assembly, General: Install attachment assembly required to support metal composite material wall panels and to provide a complete weathertight wall system, including subgirts, perimeter extrusions, tracks, drainage channels, panel clips, and anchor channels. 1. Include attachment to supports, panel-to-panel joinery, panel-to-dissimilar-material joinery, and panel-system joint seals. B. Installation: Attach metal composite material wall panels to supports at locations, spacings, and with fasteners recommended by manufacturer to achieve performance requirements specified. 1. Dry Seal Systems: Seal horizontal and vertical joints between adjacent metal composite materialwall panels with manufacturer's standard gasket system. Giant Eagle Market #6550 The Bridges, Carmel, Indiana Building Shell Bid & Permit DLA Project 2014040.00 August 12, 2014 METAL COMPOSITE MATERIAL WALL PANELS 074213 - 5 C. Accessory Installation: Install accessories with positive anchorage to building and weathertight mounting, and provide for thermal expansion. Coordinate installation with flashings and other components. D. Flashing and Trim: Comply with performance requirements, manufacturer's written installation instructions, and SMACNA's "Architectural Sheet Metal Manual." Provide concealed fasteners where possible, and set units true to line and level as indicated. Install work with laps, joints, and seams that are permanently watertight. 3.3 CLEANING A. Remove temporary protective coverings and strippable films, if any, as metal composite material panels are installed, unless otherwise indicated in manufacturer's written installation instructions. On completion of metal composite material panel installation, clean finished surfaces as recommended by metal composite material panel manufacturer. Maintain in a clean condition during construction. END OF SECTION 074213