HomeMy WebLinkAbout084233 revolving door entrances.pdf Giant Eagle Market #6550 The Bridges, Carmel, Indiana
Building Shell Bid & Permit
DLA Project 2014040.00
August 12, 2014
REVOLVING DOOR ENTRANCES 084233 - 1
SECTION 084233 - REVOLVING DOOR ENTRANCES
PART 1 - GENERAL
1.1 SUMMARY
A. Section Includes: Manual revolving door entrances.
1.2 ACTION SUBMITTALS
A. Product Data: For each type of product indicated.
B. Shop Drawings: Include plans, elevations, sections, details, and attachments to other work.
Indicate enclosures, speed-control units, and other components not in manufacturer's product
data.
1.3 INFORMATIONAL SUBMITTALS
A. Product test reports.
B. Warranties: Samples of special warranties.
1.4 CLOSEOUT SUBMITTALS
A. Operation and maintenance data.
1.5 QUALITY ASSURANCE
A. Installer Qualifications: Manufacturer's authorized representative who is trained and approved
for installation of units required for this Project.
B. Regulatory Requirements: Wings shall be capable of collapsing into a book-fold position to
provide minimum aggregate parallel width of 36 inches when breakaway force of no more than
130 lbf is applied within 3 inches of outer edges. Set maximum turning speed to comply with
requirements of authorities having jurisdiction.
C. Safety Glass: Category II materials complying with testing requirements in 16 CFR 1201.
D. Revolving Door Entrance Standard: BHMA A156.27.
Giant Eagle Market #6550 The Bridges, Carmel, Indiana
Building Shell Bid & Permit
DLA Project 2014040.00
August 12, 2014
REVOLVING DOOR ENTRANCES 084233 - 2
1.6 WARRANTY
A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or
replace components of revolving door entrances that fail in materials or workmanship within
specified warranty period.
1. Warranty Period for Revolving Door Entrances: Three years from date of Substantial
Completion.
2. Warranty Period for Finishes: 20 years from date of Substantial Completion.
PART 2 - PRODUCTS
2.1 MANUAL REVOLVING DOOR ENTRANCES
A. Give preference to materials with high recycled content and those that are
extracted/manufactured within 500 miles of the project site. Include these products in
Contractor’s LEED Action Plan and Subcontractor Scope and product purchase review in order
to increase the likelihood of achieving 2 points for recycled content and 2 points for regional
materials.
Description: Provide manufacturer's standard three-wing manual revolving door entrance, com-
plete with center shaft, speed-control unit, wings, enclosure walls, canopy, hardware, glass and
glazing, and accessories as indicated.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Record USA
Model AL-1000-M 3-Wing Manual Revolving Door Unit. Contact: Bill Warden, Trinity
Door Systems (877) 603-2018.
2. Manual-Push Activation: Pushing wing activates unit and maintains rotation of wings for
manufacturer’s standard preset time.
3. Stile-and-Rail Wings: Manufacturer's standard with 1-3/4-inch- thick tubular stile-and-
rail members.
a. Stile Design: Medium stile.
b. Rail Design: 4-inch nominal height.
c. Muntin Design: To match stile design.
d. Glass: Clear, fully tempered float glass.
4. Push Bars: Manufacturer's standard push bars, finished to match wings.
5. Locks: Manufacturer's standard deadbolt locks to receive cylinders; minimum of two for
each revolving door entrance.
a. Cylinders: Comply with requirements in Section 087100 "Door Hardware."
b. Mounting: Mortised.
c. Location: Extend bolt from bottom of wing into floor.
6. Enclosure Walls: Manufacturer's standard, with 1-3/4-inch- thick tubular framing
members.
a. Configuration: Segmented.
b. Glass: As indicated on Drawings.
c. Muntin Bars: Horizontal tubular rail member for each enclosure wall; match stile
design.
7. Canopy: Manufacturer's standard ceiling, fascia, roof, and framing with size, layout,
materials, and exposed finishes matching enclosure walls unless otherwise indicated.
Giant Eagle Market #6550 The Bridges, Carmel, Indiana
Building Shell Bid & Permit
DLA Project 2014040.00
August 12, 2014
REVOLVING DOOR ENTRANCES 084233 - 3
8. Canopy Roof: Manufacturer's standard, of material and finish matching enclosure walls
where visible.
B. Materials: Extruded aluminum.
1. Main Extrusions and Tubing: Minimum wall thickness of 0.125 inch.
2. Cladding: Minimum 0.04 inch thick.
C. Fabrication: Fabricate revolving door entrance components to designs, sizes, thicknesses, and
configurations indicated with profiles that are sharp, straight, and free of defects or
deformations. Accurately fit joints with ends coped or mitered to produce hairline joints free of
burrs and distortion. Prefit all hardware at the factory. Provide anchorage and alignment
brackets for concealed support of assembly from the building structure.
1. Wings: Factory fabricated and assembled in profiles indicated. Reinforce as required to
support imposed loads and for installing hardware.
a. Glaze wings at the factory. Comply with glazing requirements specified in this
Section and in Section 088000 "Glazing." Provide minimum clearances for
thickness and type of glass indicated according to GANA's "Glazing Manual."
b. Provide sliding weather stripping, mortised into stiles and rails of wings, to be
adjustable and replaceable without dismantling wings.
c. Mechanically Joined Construction: Joints shall be tightly bolted together. Glass
stops shall be snap-in type where possible.
2. Enclosure Walls and Canopy: Fabricate tubular and channel frame assemblies in
configuration indicated, with welded or mechanical joints, according to manufacturer's
standards and as specified. Provide subframes as required for a complete system to
support required loads.
3. Exterior Framing: Fabricate components to drain water passing joints and condensation
and moisture occurring or migrating within the system to the exterior.
2.2 MATERIALS
A. Aluminum: Alloy and temper recommended by manufacturer for type of use and finish
indicated.
1. Extruded Bars, Rods, Profiles, and Tubes: ASTM B 221.
2. Sheet and Plate: ASTM B 209.
B. Steel: ASTM A 36/A 36M plate, shapes, and bars; or ASTM A 1008/A 1008M sheet.
C. Fasteners: Manufacturer's standard, of same basic metal as fastened metal, unless otherwise
indicated.
D. Glazing Materials: Comply with requirements in Section 088000 "Glazing."
E. Weather Stripping: Heavy-duty, single-piece rubber or combination of rubber and felt.
F. Nonshrink, Nonmetallic Grout: Premixed, nonmetallic, noncorrosive, nonstaining grout;
complying with ASTM C 1107/C 1107M; of consistency suitable for application.
Giant Eagle Market #6550 The Bridges, Carmel, Indiana
Building Shell Bid & Permit
DLA Project 2014040.00
August 12, 2014
REVOLVING DOOR ENTRANCES 084233 - 4
G. Corrosion-Resistant Coating: Cold-applied asphalt mastic, compounded for 15-mil dry film
thickness per coat.
2.3 ALUMINUM FINISHES
A. Interior and exterior: Clear anodized.
PART 3 - EXECUTION
3.1 INSTALLATION
A. General: Do not install damaged components. Fit frame joints to produce hairline joints free of
burrs and distortion. Rigidly secure nonmovement joints. Seal joints watertight.
1. Where aluminum will contact dissimilar metals, protect against galvanic action by
painting contact surfaces with primer or by applying sealant or tape recommended by
manufacturer for this purpose.
2. Where aluminum will contact concrete or masonry, protect against corrosion by painting
contact surfaces with corrosion-resistant coatings.
B. Install revolving door entrances according to manufacturer's written instructions, plumb and
true, without warp or rack of framing members and wings. Anchor securely in place.
1. Install surface-mounted hardware using concealed fasteners to greatest extent possible.
2. Install components to drain water passing joints, condensation occurring within framing
members, and moisture migrating within the assembly to exterior.
3. Cut and trim framing during installation only with approval of manufacturer.
a. Restore finish and remove and replace members, as directed, where cutting and
trimming have impaired strength or appearance.
b. Do not install members that are warped, bowed, deformed, or otherwise damaged
or defaced to such an extent as to impair strength or appearance. Remove and
replace members that have been damaged during installation.
C. Sealants: Comply with requirements specified in Section 079200 "Joint Sealants" to provide
weathertight installation.
1. Set continuous sill members and flashings in full sealant bed.
2. Seal perimeter of framing members with sealant.
D. Adjust wings to provide an even, tight fit at contact points and weather stripping for smooth
operation and weathertight closure. Adjust wings to operate smoothly and rotate evenly, with
hardware and operators functioning properly.
1. Lubricate operating hardware and other moving parts.
2. Adjust speed-control unit for specified rpm.
3. Adjust pressure for collapse of wings for specified breakaway force.
E. Readjust wings and speed-control units after repeated operation of completed installation
equivalent to three days' use by normal traffic (100 to 300 cycles). Lubricate hardware and other
moving parts.
Giant Eagle Market #6550 The Bridges, Carmel, Indiana
Building Shell Bid & Permit
DLA Project 2014040.00
August 12, 2014
REVOLVING DOOR ENTRANCES 084233 - 5
3.2 DEMONSTRATION
A. Engage a factory-authorized service representative to train Owner's maintenance personnel to
adjust, operate, and maintain revolving door entrances.
END OF SECTION 084233