The URL can be used to link to this page

Home My WebLink About16120030 Building PlansArchitectural: Kyle Hardie MSKTD & Associates kfh@msktd.com 317.917.1190 Electrical: Kris Ashcraft Ermco, Inc. kashcraft@ermco.com 317.423.3888 Mechanical & Plumbing: Kevin Hutton Genesis Engineering khutton@genesis- engineering.com 317.501.9737 Interiors: Sarah Savage MSKTD & Associates sjs@msktd.com 317.917.1190 Contractor: Carl Dennin Messer Construction CDennin@messer.com 317.223.9460ROOM NAME 101 1t A 101A A2-1 1 SIM SHEET NUMBER DETAIL NUMBER SHEET NUMBER X X NEW DOOR AND FRAME ROOM NAME AND NUMBER ELEVATION SYMBOL PLAN DETAIL NEW COLUMN LINE EXISTING COLUMN LINE SECTION PARTITION TYPE WINDOW ELEVATION SYMBOL TOILET ACCESSORY 1i3.5A 1 A5-1 SIM DETAIL NUMBER NORTH ARROW PROJECT NORTH TRUE NORTH SHEET NUMBER DETAIL NUMBER x /Xx-x XXX EQUIPMENT TAGTAG ID x 1XX-YYY FURNITURE TAGTAG ID x QUANTITY 1 SPECIFIC CONSTRUCTION NOTES 1 SPECIFIC DEMOLITION NOTES 1.CONTRACTORS SHALL BE RESPONSIBLE FOR VISITING THE SITE TO BECOME FAMILIAR WITH AND VERIFY THE EXISTING CONDITIONS. THESE DEMOLITION DRAWINGS SHALL SERVE TO AID THE CONTRACTOR IN HIS EVALUATION OF THE EXTENT OF DEMOLITION; BUT SHALL NOT BE HELD TO BE ALL INCLUSIVE. 2.CONTRACTORS SHALL BE RESPONSIBLE FOR ALL DEMOLITION REQUIRED FOR THE INSTALLATION OF NEW CONSTRUCTION AND AS NECESSARY TO FULFILL THE PURPOSE AND INTENT OF THE FINISHED WORK, WHETHER OR NOT IT IS SPECIFICALLY SHOWN OR NOTED IN THESE DOCUMENTS. THE CONTRACTOR SHALL BE RESPONSIBLE FOR ALL ITEMS CALLED TO BE REMOVED THROUGH OUT THE ENTIRE SET OF DOCUMENTS. 3.CONTRACTORS SHALL FIELD INSPECT ALL DEMOLITION WORK PRIOR TO REMOVAL, TO INSURE SUCH REMOVAL DOES NOT IMPAIR STRUCTURAL INTEGRITY OF THE EXISTING BUILDING. IF THE INSPECTION INDICATES THAT THE STRUCTURAL INTEGRITY MAY BE IMPAIRED, NOTIFY THE ARCHITECT/ENGINEER IMMEDIATELY. 4.REMOVE ALL DAMAGED OR EXISTING FINISH MATERIALS FROM REMAINING WALLS, PARTITIONS AND COLUMNS (GYPSUM BOARD,WALL FABRIC, PANELING, TILE, MASONRY, CONCRETE, ETC...). PATCH WALLS AND COLUMNS AS REQUIRED TO RECEIVE NEW FINISH MATERIALS. 5.CONTRACTORS SHALL BE RESPONSIBLE FOR PROVIDING, INSTALLING AND MAINTAINING DUST TIGHT TEMPORARY CONSTRUCTION BARRIERS TO ALL AREAS WITHIN THE CONSTRUCTION LIMIT LINES, DURING THE CONSTRUCTION PROCESS. LOCATIONS SHALL BE COORDINATED WITH THE OWNER AND ARCHITECT. 6.ALL CONSTRUCTION AREAS, REMOVAL TRAFFIC PATTERN AREAS AND ASSOCIATED WORK AREAS SHALL BE KEPT CLEAN OF DEBRIS BY THE CONTRACTORS DAILY. 7.PROTECT FROM DEMOLITION AND RECONSTRUCTION DEBRIS, ALL "EXISTING TO REMAIN" FIXTURES AND EQUIPMENT REQUIRED TO REMAIN IN PLACE DURING CONSTRUCTION. 8.REFER TO REMAINING DRAWINGS FOR RECONSTRUCTION. ALL CONTRACTORS SHALL COORDINATE THE DEMOLITION AND RECONSTRUCTION WORK, TO BE ASSURED THAT THEIR WORK IS COMPLIMENTARY TO THE WORK OF ALL OTHER CONTRACTORS AND COMPLETE IN ALL RESPECTS. 9.UNLESS NOTED OTHERWISE ALL DEMOLITION MATERIAL BECOMES THE PROPERTY OF THE CONTRACTORS AND IS TO BE REMOVED FROM THE PROPERTY, IN A LEGAL MANNER. THE OWNER RESERVES THE RIGHT AND SHALL BE GIVEN THE OPPORTUNITY TO CLAIM ITEMS WHETHER OR NOT THOSE ITEMS WERE SPECIFICALLY NOTED FOR REMOVAL, RELOCATION, OR AS RETURNED TO OWNER AND SAME SHALL BE RETURNED TO OWNER. 10.THE CONTRACTOR RESPONSIBLE FOR GENERAL DEMOLITION WORK SHALL COORDINATE ANY AND ALL ASBESTOS REMOVAL WITH THE OWNER. ALL ASBESTOS REMOVAL WILL BE PREFORMED BY A LICENSED ASBESTOS REMOVAL CONTRACTOR. THIS TYPICALLY INCLUDES FLOOR TILE, TILE MASTIC AND PIPE INSULATION. 11.ITEMS SHOWN IN LIGHTER PEN WEIGHTS ARE EXISTING TO REMAIN. 12.GENERAL CONTRACTOR RESPONSIBLE FOR PATCHING ALL REMOVED ELECTRICAL OUTLETS. ELECTRICAL CONTRACTOR TO PROVIDE GENERAL CONTRACTOR WITH QUANTITIES. 13.REMOVE EXISTING FINISHES AS REQUIRED TO INSTALL NEW FINISHES. PREPARE SURFACES TO RECEIVE NEW FINISH AS PER FINISH MANUFACTURER'S PRINTED INSTRUCTIONS, SEE FINISH SCHEDULE FOR NEW FINISHES. 14.REMOVE EXISTING CEILINGS AND CEILING SUPPORT SYSTEM WHERE NEW CEILINGS ARE INDICATED, UNLESS OTHERWISE NOTED. THESE NOTES SHALL APPLY TO ALL DEMOLITION DRAWINGS AND TO ALL CONTRACTORS AND/OR SUBCONTRACTORS THAT WORK ON THIS PROJECT. INDICATES EXISTING WALL TO BE REMOVED IN ITS ENTIRETY. INDICATES EXISTING DOOR, FRAME AND ASSOCIATED HARDWARE TO BE REMOVED IN ITS ENTIRETY. SEE DOOR SCHEDULE FOR ITEMS TO BE SALVAGED AND REUSED IN OTHER AREAS. THESE NOTES APPLY TO ALL FLOOR PLANS, AND TO ALL CONTRACTORS AND/OR SUBCONTRACTORS THAT WORK ON THIS PROJECT. 1.OWNER WILL REMOVE ALL FURNISHINGS, LOOSE EQUIPMENT, SUPPLIES, ETC.... PRIOR TO CONSTRUCTION COMMENCING. 2.ALL EQUIPMENT AND MATERIALS LABELED AS "SALVAGE" OR "RELOCATE AS DIRECTED BY OWNER" SHALL BE REMOVED, PROPERLY PROTECTED AND TRANSPORTED TO A LOCATION ON THE PREMISES AS DIRECTED BY THE OWNER. 3.ALL GENERAL CONTRACTORS AND THEIR SUBCONTRACTORS SHALL BE RESPONSIBLE FOR VISITING THE CONSTRUCTION SITE TO BECOME FAMILIAR WITH ALL EXISTING CONDITIONS WHICH AFFECT THAT SPECIFIC PORTION OF THEIR WORK. ANY CONFLICTS OR APPARENT DEFICIENCIES MUST BE SUBMITTED TO THE ARCHITECT IN WRITING PRIOR TO BIDDING. 4.THE GENERAL CONTRACTOR SHALL BE RESPONSIBLE FOR INFORMING IN WRITING THE OWNER ON A WEEKLY BASIS OF THE CONSTRUCTION SCHEDULE FOR THE APPROACHING TWO WEEKS CONSTRUCTION ACTIVITY. ANY STORAGE OF MATERIALS, ACCESS OR EGRESS PROBLEMS, TRAFFIC FLOW OR NORMAL OWNER OPERATIONS WHICH ARE TO BE AFFECTED MUST BE PROTECTED AND/OR AGREED UPON BY THE OWNER. ALL COSTS SHALL BE INCURRED BY THE GENERAL CONTRACTOR. 5.THE GENERAL CONTRACTOR SHALL PROVIDE ALL NECESSARY WOOD BLOCKING FOR ALL TRADES. THIS BLOCKING SHALL BE FIRE RETARDANT. 6.ANY PLASTER WORK REQUIRING NEW FINISH SHALL BE SMOOTH, SOUND AND IN A FLUSH PLANE BEFORE FINISH APPLICATION. CONTRACTOR SHALL REPAIR THE SURFACE FOR THE NEW FINISH AS SCHEDULED. 7.ALL FIRE RATED WALLS AND FLOOR PENETRATIONS MUST COMPLY WITH ASTME-814. 8.ITEMS SHOWN IN LIGHTER PEN WEIGHT ARE EXISTING TO REMAIN. 9.REMOVE ALL DAMAGED GYPSUM BOARD, MASONRY, CONCRETE, PLASTER, ETC... FROM EXISTING SURFACES AND REPAIR TO MATCH ADJACENT CONSTRUCTION PRIOR TO REFINISHING. ALL SURFACES SHALL BE SMOOTH AND IN A FLUSH PLANE. 10.ALL CONSTRUCTION AREAS, REMOVAL TRAFFIC PATTERN AREAS AND ASSOCIATED WORK AREAS SHALL BE KEPT CLEAN OF DEBRIS BY THE CONTRACTORS DAILY. 11.PROTECT FROM DEMOLITION AND RECONSTRUCTION DEBRIS, ALL "EXISTING TO REMAIN" FIXTURES AND EQUIPMENT REQUIRED TO REMAIN IN PLACE DURING CONSTRUCTION. 12.REFER TO REMAINING DRAWINGS FOR RECONSTRUCTION. ALL CONTRACTORS SHALL COORDINATE THE DEMOLITION AND RECONSTRUCTION WORK, TO BE ASSURED THAT WORK IN EITHER OF THESE AREAS IS COMPLEMENTARY TO THE OTHER AND COMPLETE IN ALL RESPECTS. ANY CONFLICTS OR APPARENT DEFICIENCIES MUST BE SUBMITTED TO THE ARCHITECT IN WRITING PRIOR TO BIDDING. 13.ALL WALL HUNG CASEWORK REQUIRES CONTINUOUS HORIZONTAL WOOD BLOCKING BETWEEN STUDS AT TOP AND BOTTOM OF CASEWORK. BRACE WALL TO DECK AS REQUIRED. 14.ALL DIMENSIONS ARE FROM FACE OF BASE MATERIAL (STUD/CMU) TO FACE OF BASE MATERIAL (STUD/CMU) UNLESS NOTED OTHERWISE. 15.PORTIONS OF THE BUILDING SHALL BE OCCUPIED DURING CONSTRUCTION. THE GENERAL CONTRACTOR SHALL FOLLOW THE FOLLOWING LIFE SAFETY ISSUES. FAILURE TO LIST ALL LIFE SAFETY ISSUES DOES NOT RELIEVE THE CONTRACTORS FROM COMPLYING WITH FEDERAL, STATE AND LOCAL CODES, THE CONTRACTUAL AGREEMENT BETWEEN THE CONTRACTOR AND OWNER, AND OTHER GOVERNING BODIES WHICH HAVE JURISDICTION ON THIS PROJECT. THE FOLLOWING ARE INTERIM LIFE SAFETY CODE ISSUES WHICH ARE SPECIFIC TO THIS PROJECT AND MUST BE ADDRESSED: a.INSURE ALL EXITS PROVIDE FREE AND UNOBSTRUCTED EGRESS. STAFF AND PERSONNEL SHALL RECEIVE TRAINING AND WRITTEN NOTIFICATION IF ALTERNATIVE EXITS MUST BE DESIGNATED. b.INSURE FREE AND UNOBSTRUCTED ACCESS TO EMERGENCY DEPARTMENTS OR SERVICES FOR EMERGENCY FORCES. COORDINATE WITH OWNER AND ARCHITECT. c.INSURE FIRE ALARM, DETECTION AND SUPPRESSION SYSTEMS ARE NOT IMPAIRED. A TEMPORARY, BUT EQUIVALENT, SYSTEM SHALL BE PROVIDED, INSTALLED AND TESTED PRIOR TO ANY EXISTING FIRE SYSTEM BEING IMPAIRED. d.INSURE TEMPORARY CONSTRUCTION PARTITIONS ARE SMOKE TIGHT AND BUILT OF NON COMBUSTIBLE MATERIALS. THESE PARTITIONS SHALL BE COORDINATED WITH THE OWNER AND ARCHITECT. e.SMOKING SHALL BE PROHIBITED EXCEPT IN DESIGNATED AREAS OF THE BUILDING. f.DEVELOP AND ENFORCE STORAGE, HOUSEKEEPING AND DEBRIS REMOVAL PROCEDURES THAT REDUCE THE FLAMMABLE AND COMBUSTIBLE FIRE LOAD TO THE LOWEST LEVEL NECESSARY FOR DAILY OPERATIONS. g.IOSHA REQUIRES MATERIAL SAFETY DATA SHEETS (MSDS) FOR ALL MATERIALS BEING USED OR STORED ON THIS PROJECT BE MADE AVAILABLE TO ALL WORKERS ON THIS JOBSITE. COPIES MUST BE PROVIDED TO THE OWNER'S DIRECTOR OF SECURITY, IMMEDIATELY, AS WORK BEGINS. h.SECURE ALL TOOLS AND CONSTRUCTION MATERIALS DURING BREAKS AND NON-CONSTRUCTION HOURS. 1.ALIGN ALL CEILING AND BULKHEAD REVEALS, CONTROL OR SEISMIC JOINTS WITH THE ADJACENT REVEAL, CONTROL OR SEISMIC JOINTS IN WALLS INDICATED ON ELEVATIONS. 2.ALL CEILING AND BULKHEAD HEIGHTS INDICATED ARE TO FINISHED FACE OF GYPSUM BOARD OR TO THE BOTTOM FACE OF ACOUSTICAL CEILING TILE PAD, UNLESS NOTED OTHERWISE. 3.CEILING CONTRACTOR TO PROVIDE ALL CEILING GRID TO SUPPORT HVAC SUPPLY DIFFUSERS AND RETURN GRILLS. 4.DEVICES OTHER THAN LIGHTING AND DIFFUSERS ARE SHOW IN APPROXIMATE LOCATIONS, FINAL LOCATION TO BE COORDINATED WITH ALL TRADES AND ARCHITECT. 5.AT LOCATIONS WHERE GYPSUM BOARD CEILINGS ARE INDICATED, THE CONTRACTOR HAS THE OPTION TO USE LIGHT GAGE METAL FRAMING OR SUSPENDED GYPSUM BOARD GRID UNLESS OTHERWISE DETAILED. THE CONTRACTOR WILL COORDINATE ANY MODIFICATIONS WITH THE OTHER TRADES ON THE PROJECT. THE CEILING CONTRACTOR'S FINAL MEANS AND METHODS WILL NOT CONFLICT WITH THE WORK OF OTHERS OR THE INTENT OF THESE DOCUMENTS. 6.WHERE EXISTING SUSPENDED ACOUSTICAL CEILINGS ARE SCHEDULED TO REMAIN, CUT AND PREP THE CEILING GRID IN PREPARATION FOR REPAIRING. SALVAGE ENOUGH CEILING PADS FOR RECONSTRUCTION. STORE AND PROTECT ALL MATERIALS. USE NEW MATCHING MATERIALS FOR RECONSTRUCTION AS REQUIRED. 7.SEE THE ROOM FINISH SCHEDULE FOR ADDITIONAL COMMENTS REGARDING MATERIALS AND FINISHES. 8.THE DESIGNATION 'CJ' INDICATES GYPSUM BOARD CONTROL JOINTS. WHERE INDICATED PROVIDE USG #093 ZINC CONTROL TYPICAL. INSTALL JOINT THROUGH THE FULL EXTENTS OF ANY GYPSUM CEILING OR BULKHEAD. WHERE THE GYPSUM CEILING COMPONENT MEETS A GYPSUM WALL, EXTEND THE CONTROL JOINT DOWN TO THE FLOOR TYPICAL. 9.THE GENERAL CONTRACTOR WILL PROVIDE AND INSTALL ALL SUPPLEMENTAL AND/ OR MISCELLANEOUS STEEL FRAMING AS REQUIRED BY THEMSELVES OR BY THEIR SUBCONTRACTORS FOR THE INSTALLATION OF THE EQUIPMENT SCHEDULED AND SPECIFIED. NOT ALL OF THE REQUIRED SUPPORT STEEL MAY BE DETAILED OR CALLED OUT FOR IN THESE DOCUMENTS. COORDINATE ALL REQUIREMENTS WITH THE SPECIFICATIONS, EQUIPMENT SUPPLIERS AND SUBCONTRACTORS. THERE WILL BE NO CHANGE ORDERS TO THE PROJECT FOR SUPPLEMENTAL STEEL WHERE OMISSIONS MAY OCCUR IN THE BIDDING DOCUMENTS. THESE NOTES APPLY TO ALL CONSTRUCTION DRAWINGS AND TO ALL CONTRACTORS AND/OR SUBCONTRACTORS THAT WORK WITHIN THIS BUILDING. EXTEND TO BOTTOM OF DECK ABOVE 1.5A 5/8" GYPSUM BOARD (BOTH SIDES) 3 5/8" METAL STUD AT 16" O.C. EXTEND TO BOTTOM OF DECK ABOVE 1.7A SOUND ATTENUATION BLANKET INSULATION 5/8" GYPSUM BOARD (BOTH SIDES) 6" METAL STUD AT 16" O.C. SOUND ATTENUATION BLANKET INSULATION 4 7/8"7 1/4"DAVIDARCHI T E C TREG IS TERE DAR10500075 STATE OF I IND A AN No. S L TA ERN IC H LOAS Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO.DATE 6979 12-02-16 MSKTD& Associates IREquipmentReplacementDate Signed 12-02-16 12/1/20165:19:26PMTitlesheet, Drawing Index and General Info G1-1 11700N.MeridianStreet|Carmel,Indiana46032NorthHospitalARenovationForIR Equipment Replacement Drawing Index North Hospital Plumbing CHK Check List Q2-8 Site Specific Philips Equipment ED2 Electrical Details ED3 Electrical Details N1 Remote Service Network N2 Remote Service Network Q2-7 Site Specific Philips Equipment E1 Electrical Plan E2 Raceway & Conduit Information E3 Raceway & Conduit Information ED1 Electrical Details Q2-6 Site Specific Philips Equipment SD3 Support Details SD4 Support Details EN Electrical Notes EL Electrical Legend Q2-5 Site Specific Philips Equipment S1 Support Plan - Floor & Wall S2 Support Plan - Ceiling SD1 Support Details SD2 Support Details Q2-4 Site Specific Philips Equipment AD5 Equipment Details AD6 Equipment Details SN Support Notes SL Support Legend Q2-3 Site Specific Philips Equipment AD1 Transport Details AD2 Equipment Details AD3 Equipment Details AD4 Equipment Details Q2-2 Site Specific Philips Equipment C1 Philips Equipment Cover Sheet AN General Notes AL Equipment Legend A1 Equipment Plan Q2-1 Site Specific Philips Equipment A2-1 First Floor Plans A9-1 First Floor Reflected Ceiling & Finish Plans, Casework Elevation G1-1 Titlesheet, Drawing Index and General Info G1-2 Life Safety Plans and Code Summary Architectural Electrical ContactsGraphic SymbolsGeneral Demolition Notes General Reconstruction Notes General Ceiling Notes Partition Types P001 Plumbing Symbols and Abbreviations P002 Plumbing Specifications P210 First Floor Plumbing Plans M001 Mechanical Symbols and Abbreviations M002 Mechanical Specifications M003 Mechanical Specifications M210 First Floor Mechanical Plans M600 Mechanical Schedules and Temp. Control Schematics M700 Mechanical Details E001 Electrical Symbols and Abbreviations E002 Electrical Specifications E100 Overall Ground Floor Plan E110 Overall First Floor Plan E210 First Floor Lighting Plans E310 First Floor Power and Systems Plans E600 Electrical Schedules E700 Electrical Details Mechanical Site Specific EquipmentSite Specific Equipment REV.DATE REF.LR-2219MAX.24"x24"BASEMIN.LR-2219MAX.24"x24"BASEMIN.LR-2219MAX.24"x24"BASEMIN.30"x24"BASEMIN.24"x24"BASEMI N. TUBE EPODN UP UP DN DN UP UP DN c c FE FE FE FE FEFE P FE FE P P FE P SUITE 5,580 SF SUITE 4,100 SF SUITE 550 SF SMOKE ZONE 1.5 15,543 SF 326 SF IMAGING B133A 160 SF ES CLOSET B142 71 SF SOILED UTILITY B162 528 SF IR CATH LAB B168 139 SF CONTROL ROOM B167 33 SF EQ. STORAGE B167A 237 SF CLEAN UTILITY B173 110 SF SOIL UTILITY B174 93 SF SOILED LINEN B152 CONSTRUCTION LIMIT APPLICABLE CODES: NFPA 101 Life Safety Code 2012 Edition. Chapter 18 New Healthcare Occupancies. BUILDING/DWELLING CODE 2014 Indiana Building Code (675 IAC 13-2.6) STRUCTURAL CODE 2014 Indiana Building Code (2006 IBC, ANSI A-117.1-2003, ASCE-7-2005) MECHANICAL CODE 2014 Indiana Mechanical Code (2006 IMC with state amendments) ELECTRICAL CODE 2009 Indiana Electrical Code (2008 NEC with state amendments) FIRE/LIFE SAFETY CODE 2014 Fire Code (675 1AC 22-2.5) consisting of 2012 IFC with state amendments ACCESSIBILITY CODE 2014 Indiana Building Code, Chapter 11, and ICC standard A117.1 2009 edition ENERGY CODE 2010 Indiana Energy Conservation Code (ASHRAE 90.1 - 2007 with state amendments) BUILDING:Hospital OCCUPANCY:Group I-2, Institutional IBC sec. 308.4 CONSTRUCTION TYPE Type I-A IBC Table 601 AUTOMATIC SPRINKLERS:Yes – Fully-Sprinkled AREA ALLOWABLE BUILDING AREA:Unlimited IBC Table 503 FLOOR AREAS (GROSS): EXISTING:RENOVATION: Lower Level: 83,364 SF N/A First Floor: 88,200 SF 750 SF Second Floor: 87,990 SF N/A Third Floor: 73,802 SF N/A Fourth Floor: 71,365 SF N/A Fifth Floor: 70,255 SF N/A Sixth Floor: 30,038 SF N/A Seventh Floor: 3,656 SF N/A (Penthouse) TOTAL GROSS AREA:508,670 SF 750 SF HEIGHT: ALLOWABLE STORIES:Unlimited IBC Table 503 STORIES:Seven (7) including a Lower Level (Basement), plus Penthouse FIRE RESISTANT REQUIREMENTS : (NON-COMBUSTIBLE) Structural Framing 3-Hour IBC Table 601 Floor – Ceiling 2-Hour IBC Table 601 Roof 1 1/2-Hour IBC Table 601 SHAFT ENCLOSURES: 3 Stories or Less 2-Hour NFPA 101; 8.3.4.2/IBC 713.4 4 Stories or More 2-Hour VERTICAL CIRCULATION: 2-Hour NFPA 101; 8.3.4.2 OCCUPANCY SEPARATION:B Occ. and I-2 Occupancy 2-Hour SMOKE BARRIERS:(I-2 Occupancy and in B Occupancy located within 1-floor of I-2) Max Area:22,500 SF Max Travel Distance:200 Ft. TRAVEL DISTANCE TO AN EXIT: B Occupancy 300 Ft. I-2 Occupancy 200 Ft. (50’ within Room + 150’) 1 HOUR FIRE BARRIER (Hazardous Rooms) 2 HOUR FIRE BARRIER (Occupancy Separation) SMOKE BARRIER WALL (1 Hour Rated Walls, 20 Min. Rated Doors) TRAVEL DISTANCE (Distance to Smoke Barrier) SMOKE TIGHT EXIT ACCESS CORRIDOR (Non-Rated Corridors; Hazardous Areas) SUITE (Bounding walls to be Smoke Resistant) 2 HOUR FIRE BARRIER (Vertical Openings) 2 HOUR FIRE BARRIER (Exit Passageways / Horizontal Exit) SMOKE PARTITION (Hazardous Rooms) EXIT TRAVEL DISTANCE (Distance to Exit) NFPA 101 LIFE SAFETY CODE (2000) CHAPTER 18 (New Healthcare Occupancy) NFPA 101 LIFE SAFETY CODE (2000) CHAPTER 38 (New Business Occupancy) P MANUAL FIRE ALARM PULL STATION STANDPIPE OUTLET CHUTE (TRASH & LINEN) FIRE EXTINGUISHERFE c FIRE RESISTIVE CEILING (Bounding walls to be 1 Hour Rated Fire Barrier) LIFE SAFETY CODE REVIEW (Per NFPA 101, 2012 Edition) Chapter 18: New Healthcare Chapter 19: Existing Healthcare CONSTRUCTION LEGEND 2-HOUR FIRE BARRIER (Occupancy Separation) 19.1.3.4 - Occupancy separation. 18.1.3.4.1 - Occupancy separation. 19.2.2.4 Smokeproof Enclosures - "Smokeproof enclosures complying with 7.2.3 shall be permitted." 7.2.3.3 - "A smokeproof enclosure shall be continuously enclosed by barriers having a 2- hour fire resistance rating from the highest level of exit discharge. Where a vestibule is used, it shall be within the 2-hour rated enclosure and shall be considered part of the smokeproof enclosure." 18.2.2.4 Smokeproof Enclosures - "Smokeproof enclosures complying with 7.2.3 shall be permitted." 8.3.4.2 (table) - 1½-hour opening rating (doors). 2-HOUR FIRE BARRIER (Vertical Openings): 18.3.1.1 - "Any vertical opening shall be enclosed or protected in accordance with 8.2.5." 8.6.5 – Enclosures connecting four stories or more in new construction – 2 hour fire barriers Other enclosures in new construction: 1-hour fire barriers. 8.6.7- Atriums are separated from the adjacent spaces by fire barriers with not less than 1- hour fire resistance rating with opening protective for corridor walls. See exceptions in section. 8.3.4.2 (table) - 1½-hour opening rating (doors). 2-HOUR FIRE BARRIER ( Exit Passageways): 19.2.2.7 Exit Passageways - "Exit passageways complying with 7.2.6 shall be permitted." 7.2.6.2 Enclosure - "An exit passageway shall be separated from other parts of the building as specified in 7.1.3.2." 7.1.3.2.1 (b) - 2-hour fire resistive rating for four or more stories. 18.2.2.7 Exit Passageways - "Exit passageways complying with 7.2.6 shall be permitted." 8.3.4.2 (table) - 1½-hour opening rating (doors). 1-HOUR FIRE BARRIER (Hazardous Areas) 18.3.2.1 Hazardous Areas - "Any hazardous area shall be protected in accordance with Section 8.4. The areas described in Table 18.3.2.1 shall be protected as indicated." 1. Boiler and fuel-fired heater rooms 2. Central/bulk laundries larger than 100 square feet. (9.3 square meters) 3. Paint shops 4. Repair Shops 5. Soiled linen rooms 6. Trash Collection rooms 7. Rooms or spaces larger than 50 square feet (4.6 square meters) including repair shops, used for storage of combustible supplies and equipments in quantities deemed hazardous by the authority having jurisdiction. 8. Laboratories employing flammable or combustible materials in quantities less than those that would be considered a severe hazard. 18.3.6.3.11 - "Door-closing devices shall not be required on doors in corridor wall openings other than those serving required exits, smoke barriers or enclosures of vertical openings and hazardous areas." SMOKE BARRIER WALL (1-hour Rated Existing): 19.3.7.3 - "Any required smoke barrier shall be constructed in accordance with Section 8.3 and shall have a minimum 1/2 hour fire resistance rating....." 19.3.7.6 - 19.3.7.8 - Doors shall have a 20 minute fire rating and shall be self-closing or automatic closing. Doors are not required to swing with egress travel and positive latching hardware is not required. 18.3.7.3 - "Any required smoke barrier shall be constructed in accordance with Section 8.3 and shall a minumum 1-hour fire resistance rating....dampers shall not be required in fully ducted system....." 18.3.7.6 - 18.3.7.8- Doors shall have a 20 minute fire rating and shall be self-closing or automatic closing, and permitted to be held open only by an automatic releasing device. Doors shall be dual egress but positive latching hardware is not required. SMOKE ZONES (Not to Exceed 22,500 s.f.): 19.3.7.1 - "To divide every story used by inpatients for sleeping by more than 30 patients into not less than two smoke compartments;(1) To limit the size of each smoke compartment to an area not exceeding 22,500 sq. ft. (2) Where neither the length nor width of the smoke compartment exceeds 150 ft, the travel distance to each the smoke barrier door shall not be limited. 18.3.7.1 - "(1) To divide every story used by inpatients for sleeping or treatment into not less than two smoke compartments; (2) To divide every story having an occupant load of 50 or more persons, regardless of use, into not less than two smoke compartments; (3) To limit the size of each smoke compartment to an area not exceeding 22,500 sq. ft. (4) To limit the travel distance from any point to reach a door in the required smoke barrier to a distance not exceeding 200 ft. SMOKE PARTITION (Hazardous Areas): 19.3.2.1 Hazardous Areas - Any hazardous area shall be safe-guarded by a fire barrier having a 1-hour fire resistance rating or shall be provided with an automatic extinguishing system in accordance with 8.7.1. The automatic extinguishing shall be permitted to be in accordance with 19.3.5.9.Where the sprinkler option of 19.3.2.1 is used, the areas shall be separated from other spaces by smoke-resisting partitions and doors. 19.3.2.1.5 Hazardous areas shall include, but shall not be restricted to, the following: 1. Boiler and fuel-fired heater rooms 2. Central/bulk laundries larger than 100 square feet. (9.3 square meters) 3. Paint shops 4. Repair Shops 5. Soiled linen rooms 6. Trash Collection rooms 7. Rooms or spaces larger than 50 square feet (4.6 square meters) including repair shops, used for storage of combustible supplies and equipments in quantities deemed hazardous by the authority having jurisdiction. 8. Laboratories employing flammable or combustible materials in quantities less than those that would be considered a severe hazard. Exception: Doors in rated enclosures shall be permitted to have non-rated, factory- or field applied protective plates extending not more than 48in.(122cm) above the bottom of the door. SUITES (Non-Rated (Smoke Resistant) Corridors): 18.2.5.7.1.1 - Suites shall be separated from the remainder of the building, and from other suites, by walls and doors meeting corridor wall construction requirements. 19.2.5.7.1.1 - Suites shall be separated from the remainder of the building, and from other suites, by walls and doors meeting corridor wall construction requirements. 18.2.5.7.1.3 (A) - Intervening rooms shall not be hazardous areas as defined by 18.3.2. 19.2.5.7.1.3 (A) - Intervening rooms shall not be hazardous areas as defined by 18.3.2. 18.2.5.7.2.1 - (A) Sleeping Suites shall have access directly to exit corridor. (B) Where two or more exit access doors are required from a suite, one of the exit doors shall be permitted to be directly to an exit stair, exit passageway or exit door to the exterior. (C) Sleeping suites shall be provided with constant staff supervision within the suite. (D) Sleeping suites shall be arranged to provide one of the following (a) The patient sleeping rooms shall be arranged to allow for direct supervision form a normally attended location within the suite or (b) any patient rooms without direct supervision shall be provided by automatic smoke detection. 19.2.5.7.2.1 - (A) Sleeping Suites shall have access directly to exit corridor. (B) Where two or more exit access doors are required from a suite, one of the exit doors shall be permitted to be directly to an exit stair, exit passageway or exit door to the exterior. (C) Sleeping suites shall be provided with constant staff supervision within the suite. (D) Sleeping suites shall be arranged to provide one of the following (a) The patient sleeping rooms shall be arranged to allow for direct supervision form a normally attended location within the suite or (b) any patient rooms without direct supervision shall be provided by automatic smoke detection. 18.2.5.7.2.2 - Sleeping suites of more than 1000 sq. ft. shall have not less than two exit access doors remotely located from one another. One means of egress shall be directly to a corridor. One means of egress shall be permitted to be through another suite, provided that the suite separation complies with corridor construction requirements. 19.2.5.7.2.2 - Sleeping suites of more than 1000 sq. ft. shall have not less than two exit access doors remotely located from one another. One means of egress shall be directly to a corridor. One means of egress shall be permitted to be through another suite, provided that the suite separation complies with corridor construction requirements. 18.2.5.7.2.3 (B)- Sleeping suites shall not exceed 7500 sq. ft. Sleeping Suites larger than 7500 sq. ft. and not exceeding 10,000 sq. ft. shall be permitted where both direct visual supervisiion is provided and automatic smoke detection is provided. 19.2.5.7.2.3 - (B) Sleeping suites shall not exceed 7500 sq. ft. without having an electrically supervised sprinkler system and automatic smoke detection. Sleeping Suites larger than 7500 sq. ft. and not exceeding 10,000 sq. ft. shall be permitted where both direct visual supervisiion is provided and automatic smoke detection is provided. 18.2.5.7.2.4 - Suite Travel Distance between any point in a sleeping suite and the exit access door from that suite shall not exceed 100 ft. Travel distance between any point in a sleeping suite and the exit shall not exceed 200 ft. 19.2.5.7.2.4 - Suite Travel Distance between any point in a sleeping suite and the exit access door from that suite shall not exceed 100 ft. Travel distance between any point in a sleeping suite and the exit shall not exceed 200 ft if the building is protected by a sprinkler system. Without a sprinkler system, distance is limited to 150 ft. 18.2.5.7.3 -Patient Care Non-Sleeping Suites shall have direct access to an exit access corridor. 19.2.5.7.3.1 -Patient Care Non-Sleeping Suites shall have direct access to an exit access corridor. 18.2.5.7.3.2 - Non-sleeping suites of more than 2500 sq ft shall have not less than two exit access doors remotely located from one another. For suites requiring two means of egress, one means of egress from the suite shall be permitted to be through another suite provide dthat the suite separation complies with corridor wall construction. 19.2.5.7.3.2 - Non-sleeping suites of more than 2500 sq ft shall have not less than two exit access doors remotely located from one another. For suites requiring two means of egress, one means of egress from the suite shall be permitted to be through another suite provide dthat the suite separation complies with corridor wall construction. 18.2.5.7.3.3 - Patient Care Non-Sleeping Suites shall not exceed 10,000 sq. ft. 19.2.5.7.3.3 - Patient Care Non-Sleeping Suites shall not exceed 10,000 sq. ft. 18.2.6.1 - Travel distance between any point in a room and an exit shall not exceed 200 ft. 19.2.6.1 - Travel distance between any point in a room and an exit shall not exceed 150 ft. SMOKE RESISTANT CORRIDORS (Non-Rated Corridors): 19.3.6.2.4 - "In smoke compartments protected throughout by an approved, supervised automatic sprinkler system in accordance with 19.3.5.7, a corridor shall be permitted to be separated from all other areas by non-fire-rated partitions and shall be permitted to terminate at the ceiling where the ceiling is constructed to limit the transfer of smoke." 18.3.6.2 - "Corridor walls shall form a barrier to limit the transfer of smoke. Such walls shall be permitted to terminate at the ceiling where the ceiling is constructed to limit the transfer of smoke. No fire resistance rating is required for corridor walls." 19.3.6.3.4 - Door closing devices not required. 18.3.6.3.4 - Door closing devices not required. TRAVEL DISTANCES TO EXIT 18.2.6.2.1 - "The travel distance between any point in a room and an exit shall not exceed 200 feet." 19.2.6.2.2 - The travel distance between any point in a room and an exit shall not exceed 150.(Exception: The maximum travel distance shall be permitted to be increased by 50 ft. in buildings protected throughout by an approved, supervised automatic sprinkler system.) TRAVEL DISTANCES TO SMOKE 19.3.7.1 - "The size of any such smoke compartment shall not exceed 22,500 s.f., and the travel distance from any point to reach a door in the required smoke barrier shall not exceed 200 feet. (Exception No. 1: Where neither the length nor width of the smoke compartment exceeds 150 feet, the travel distance to reach the smoke barrier door shall not be limited." 18.3.7.1 (4) - "To limit the travel distance from any point to reach a door in the required smoke barrier to a distance not exceeding 200 feet."DAVIDARCHI T E C TREG IS TERE DAR10500075 STATE OF I IND A AN No. S L TA ERN IC H LOAS True NorthPlanNorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO.DATE 6979 12-02-16 MSKTD& Associates KEY PLAN IREquipmentReplacementAREA OF CONSTRUCTION Date Signed 12-02-16 12/1/20165:09:42PMLife Safety Plans and Code Summary G1-2 11700N.MeridianStreet|Carmel,Indiana46032NorthHospitalARenovationFor 1/8" = 1'-0" Partial First Floor Life Safety Plan Code SummaryLife Safety Legend Life Safety Legend Code Citations REV.DATE 14 14.9 15 16 16.1 K L READING B144 CORRIDOR B1C09 CORRIDOR B1C10 CONTROL ROOM B167 CATH LAB # 3 B166 CORRIDOR B1C08 CORRIDOR B1C13 IR CATH LAB B168 SCRUB B169 CONTROL B169A CORRIDOR B1C07 9' - 11"8'-4"3' - 3"1'-6"8'-8"EQ. STORAGE B167A 1.7A 1.5A+/-7'-81/2"1 B167A-1 /1A9-12 2 2 AREA OF CONSTRUCTION B168-1 B168-2 B167-2 5 4 2' - 4" 3 1.5 1' - 0" 6 14 14.9 15 16 16.1 K L READING B144 WORK ROOM B167 CATH LAB # 3 B166 CORRIDOR B1C08 CATH LAB #2 B168 SCRUB B169 CONTROL B169A CORRIDOR B1C07 1 2 3 +/-7'-81/2"4 5 6 9 7 8 3 7 8 10 AREA OF CONSTRUCTION SL-4 8' - 0" (FINISHED OPENING) EQ EQ EQEQ 7'-0"I-BEAM TRACK 1.FOUR-PANEL SLIDING BYPASS COMMERCIAL SYSTEM. 7'-0" HEIGHT. SIMILAR TO JOHNSON HARDWARE, 200SD. 2.EXISTING DOOR FRAME TO RECEIVE PERIMETER GASKET, AND DOOR TO RECEIVE BOTTOM SWEEP. 3.REHANG ACTNE DOOR LEAF & CONT. HINGE. MODIFY BOTTOM OF LEAF AS NECESSARY FOR FLOOR CLEARANCE. 1.WOOD (SCWD) DOORS SHALL BE CHERRY, QUARTER-SLICES, WITH CUSTOM FINISH EQUAL TO MARSHFIELD #237555C. 1.ALL PERIMETER EXISTING WALL ASSEMBLIES IN CATH LAB #2 B168 HAVE 1/16" LEAD SHIELDING UP TO 7'-0" A.F.F. CONTRACTOR IS RESPONSIBLE FOR ENSURING LEAD SHIELDING PRIORITY ON ALL ROUGH-INS, PATCHS, AND INFILLS. 1.ALL PERIMETER EXISTING WALL ASSEMBLIES IN CATH LAB #2 B168 HAVE 1/16" LEAD SHIELDING UP TO 7'-0" A.F.F. CONTRACTOR IS RESPONSIBLE FOR ENSURING LEAD SHIELDING PRIORITY ON ALL ROUGH-INS, PATCHS, AND INFILLS.DAVIDARCHI T E C TREG IS TERE DAR10500075 STATE OF I IND A AN No. S L TA ERN IC H LOAS True NorthPlanNorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO.DATE 6979 12-02-16 MSKTD& Associates KEY PLAN IREquipmentReplacementAREA OF CONSTRUCTION Date Signed 12-02-16 12/1/20165:09:36PMFirst Floor Plans A2-1 11700N.MeridianStreet|Carmel,Indiana46032NorthHospitalARenovationFor 1/4" = 1'-0" First Floor Plan 1/4" = 1'-0" First Floor Demo Plan 6979 - Specific Demo Notes 1 REMOVE CASEWORK IN IT'S ENTIRETY. 2 PARTIALLY REMOVE CASEWORK. SAW CUT EXISTING CASEWORK AT APPROXIMATELY 7'-8 1/2" LENGTH ALONG SOUTH WALL. VERIFY LOCATION OF NEW WALL PRIOR TO DEMOLITION. 3 PATCH & REPAIR EXISTING WALLS & FLOORS FOR NEW FINISHES. 4 REMOVE ALL EXISTING SHELVING & SUPPORTS IN HATCHED AREA. 5 REMOVE TWO 24"W x 12"D x 30"H 2-DOOR UPPER CABINETS. 6 REMOVE & SALVAGE 12"W x 12"D x 30"H 1-DOOR UPPER CABINET FOR REINSTALLATION. 7 REMOVE EXISTING FLOORING AND INTEGRAL COVE IN ITS ENTIRETY. 8 REMOVE CEILING SYSTEM IN ITS ENTIRETY. 9 REMOVE PORTION OF LAY-IN CEILING AS REQUIRED FOR INSTALLATION OF NEW HVAC EQUIPMENT. SALVAGE TILE AND GRID AND REINSTALL. 10 REMOVE PORTION OF BULKHEAD ABOVE UPPER CABINETS SCHEDULED FOR REMOVAL. VERIFY LOCATION OF NEW WALL PRIOR TO DEMOLITION. 1 6979 - Specific Plan Notes 1 REINSTALL SALVAGED 12"W x 12"D x 30"H 1-DOOR UPPER CABINET. 2 NEW PHILIPS IR EQUIPMENT & CONTROLS. REFER TO SITE SPECIFIC DRAWINGS 3 ISOCENTER FOR PHILIPS IR EQUIPMENT & CONTROLS. REFER TO SITE SPECIFIC DRAWINGS. 4 POWER AND MEDICAL GAS FLOOR PEDESTAL. REFER TO MEP DRAWINGS. 5 INSTALL REMOVABLE ALUMINUM FASCIA PANEL IN FRONT OF OVERHEAD SLIDING DOOR TRACK. 6 MED GAS VERTICAL DROP CHASE TO LOWER LEVEL. COORDINATE EXACT FRAMING & GYPSUM BOARD WRAP AS NECESSARY. EXISTING 1/16" LEAD LINED GYPSUM BOARD TO REMAIN INTACT ON BACKSIDE OF "WRAP." 1 6979 - Door and Opening Schedule Opening No. Door Frame Details Label Door Glass Power Req'd Hdw. Set RemarksSizeMat.Ele.Mat.Ele.Head Jamb 6979 - IR Equip Replacement B167A-1 96" x 84"SCWD SL-4 ALUM SL-4 ------1 Existing B167-2 3'-0" x 7'-0" x 1 3/4"SCWD --EX. HM ------EX. LEAD ----2 B168-1 (1) 4'-0" x 7'-0" x 1-3/4" and (1) 2'-0" x 7'-0" x 1-3/4"SCWD --EX. HM ------EX. LEAD ----2 B168-2 (1) 4'-0" x 7'-0" x 1-3/4" and (1) 2'-0" x 7'-0" x 1-3/4"SCWD --EX. HM ------EX. LEAD ----2,3 Door Elevations Door Schedule Remarks General Door Remarks REV.DATE General Note General Note 14 14.9 15 16 16.1 K L READING B144 CORRIDOR B1C09 CORRIDOR B1C10 CONTROL ROOM B167 CORRIDOR B1C08 CORRIDOR B1C13 IR CATH LAB B168 SCRUB B169 CONTROL B169A CORRIDOR B1C07 A.F.F. 8' - 10" EQ. STORAGE B167A 9' - 11"8'-4"A.F.F. 9' - 6 1/2" A.F.F. 8' - 10" 1 1 1 3 4 4 4 4 4 4 2 +/-7'-81/2"AREA OF CONSTRUCTION 6 5 B144 READING B1C09 CORRIDOR B1C10 CORRIDOR B167 CONTROL ROOM - ACT-1 P-1 SVB-1 SV-1 B1C08 CORRIDOR B168 IR CATH LAB 1,2 ACT-2 P-1+ SVB-1 SV-1 B169 SCRUB B169A CONTROL B167A EQ. STORAGE - ACT-1 P-1 SVB-1 SV-1 PT-3 AREA OF CONSTRUCTION CG CG CG CG K 7'-2"2'-6"1'-10"2'-10"3/4" FILLER 2' - 0"2' - 0"2' - 0"1' - 0"+/- 7 1/2" FILLER +/- 7' - 8 1/2" +/- 7' - 8 1/2"8' - 4"1' - 8" 18' - 3 1/4"7'-0"6"EXISTING PLASTIC LAMINATE UPPER CABINETS REINSTALLED PLASTIC LAMINATE UPPER CABINET EXISTING GYPSUM BOARD BULKHEAD EXISTING PLASTIC LAMINATE COUNTERTOP B167A-1 EXISTING UNDER COUNTER SUPPORTS, ADJUST AS NECESSARY (MAX GAP 4'-0" O.C.) FASCIA TRIM PIECE 8' - 0" NEW SIDE SPLASH FLOOR SHEET VINYL SV-1 GERFLOR, MIPOLAM SYMBIOZ, COLOR: 6041 CLAY BASE SHEET VINYL BASE SVB-1 GERFLOR, MIPOLAM SYMBIOZ, COLOR: 6041 CLAY WALL PAINT P-1 SHERWIN WILLIAMS; CRISP LINEN SW6378 P-2 SHERWIN WILLIAMS; INTERACTIVE CREAM SW6113 P-3 SHERWIN WILLIAMS; OYSTER BAY SW6206 WALL PROTECTION WP-1 KOROGUARD; K-3; PORCELAIN; INSTALL FROM TOP OF BASE TO 52" A.F.F. CEILING ACOUSTICAL TILES ACT-1 ARMSTRONG; DUNE, FINE TEXTURE 24" x 24"; #1772 ACT-2 ARMSTRONG; CLEAN ROOM, VL 24" x 24"; #868 GYPSUM BOARD CEILING / BULKHEAD 2' x 2' LAY-IN CEILING 2.UNLESS OTHERWISE NOTED, ALL CEILINGS SHALL BE 8'-10" A.F.F. (MATCH EXISTING). 1.REFER TO MECHANICAL, ELECTRICAL, AND PLUMBING DRAWINGS FOR FIXTURE TYPES AND LOCATIONS. (APPLICABLE THROUGHOUT ALL AREAS OF CONSTRUCTION) A.FOR ALL FLOORING MATERIALS INSTALLED ON GRADE OR BELOW GRADE: THE FLOORING CONTRACTOR SHALL BE RESPONSIBLE TO INCLUDE IN THEIR BID PRICES ALL REQUIRED MATERIALS AND LABOR FOR A COMPLETE INSTALLATION THAT MEETS THE MANUFACTURER'S TOTAL SYSTEM PERFORMANCE. THIS INCLUDES ALL PREP MATERIALS AND LABOR REQUIRED TO MEET MANUFACTURER'S WRITTEN SPECIFICATIONS FOR MOISTURE, PH, SMOOTHNESS OR LEVELNESS OR CLEANLINESS OF NEW OR EXISTING SUBSTRATES, ETC. THIS INSTALLATION SHALL INCLUDE THE MANUFACTURER'S SPECIFIED ADHESIVES, SEALERS, ETC. B.PAINT ALL HOLLOW METAL DOORS, WINDOW FRAMES, AND DOOR FRAMES P-2, SEMI-GLOSS. C.PATCH AND MATCH ALL FINISHES DUE TO CONSTRUCTION. D.SEE REFLECTED CEILING PLAN AND DETAILS FOR LOCATION AND HEIGHT OF CEILINGS. E.EVERY TRANSITIONS BETWEEN FLOORING MATERIALS TO BE FLUSH. IT IS FLOORING CONTRACTOR'S RESPONSIBILITY TO LEVEL SUBSTRATE AS NECESSARY FOR MATERIALS TO TRANSITION AT LEVEL HEIGHT, INCLUDING GRINDING OR BUILDING UP OF CONCRETE. ALL TRANSITION STRIPS TO BE STAINLESS STEEL EQUAL TO SCHLUTER SYSTEMS AND MUST MEET ADA; ALL PROFILES TO BE APPROVED BY ARCHITECT PRIOR TO INSTALLATION. TRANSITION STRIPS ARE UNNECESSARY BETWEEN LIKE MATERIALS (CARPET TO CARPET, LINOLEUM TO VINYL, ETC). F.PAINT VENTS, DIFFUSERS, ELECTRICAL PANELS, FIRE CABINETS (UNLESS THEY ARE NATURAL ALUMINUM OR STAINLESS STEEL), ETC. TO MATCH WALL COLOR. G.2" CORNER GUARD (CG): 12 GA STAINLESS STEEL W/ RADIUSED CORNER AND EDGES. HEIGHT TO BE 6'-8". SILICONE APPLIED. (SEE FINISH SCHEDULE FOR LOCATION) 1.SEE FINISH FLOOR PLAN FOR ACCENT PAINT LOCATION. 2.PAINT TO BE EPOXY.DAVIDARCHI T E C TREG IS TERE DAR10500075 STATE OF I IND A AN No. S L TA ERN IC H LOAS True NorthPlanNorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO.DATE 6979 12-02-16 MSKTD& Associates KEY PLAN IREquipmentReplacementAREA OF CONSTRUCTION Date Signed 12-02-16 12/1/20165:09:38PMFirst Floor Reflected Ceiling & Finish Plans, Casework Elevation A9-1 11700N.MeridianStreet|Carmel,Indiana46032NorthHospitalARenovationFor 1/4" = 1'-0" First Floor Reflected Ceiling Plan 1/4" = 1'-0" First Floor Finish Plan 1/2" = 1'-0" Casework Elevation1 Color Legend 6979 - Room Finish Schedule Room No.Name Floor Base Walls Ceiling Type (see RCP for heights)RemarksNESW B167 CONTROL ROOM SV-1 SVB-1 P-1 P-1 P-1 P-1 ACT-1 - B167A EQ. STORAGE SV-1 SVB-1 P-1 P-1 P-1 P-1 ACT-1 - B168 IR CATH LAB SV-1 SVB-1 P-1/WP-1 P-1/WP-1 P-1/WP-1 P-3/WP-1 ACT-2 1,2 General Ceiling Notes6979 - Specific RCP Notes 1 NEW ACOUSTICAL LAY-IN CEILING. REFER TO PLAN FOR CEILING HEIGHT. 2 NEW ACOUSTICAL CLEAN ROOM, GASKETED LAY-IN CEILING. COORDINATE WITH SITE SPECIFIC DRAWINGS FOR UNISTRUT LAYOUT. 3 EXISTING BULKHEAD CUT TO NEW LENGTH. ATTACH TO NEW & ADJACENT WALL FRAMING. 4 EXISTING CEILING TO REMAIN. 5 ISOCENTER FOR PHILIPS IR EQUIPMENT & CONTROLS. REFER TO SITE SPECIFIC DRAWINGS. 6 REMOVE PORTION OF LAY-IN CEILING AS REQUIRED FOR INSTALLATION OF NEW HVAC EQUIPMENT. SALVAGE TILE AND GRID AND REINSTALL. 1 General Remarks Specific Remarks REV.DATE True NorthPlanNorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO.DATE 6979 12-02-16 MSKTD& Associates KEY PLAN IREquipmentReplacementAREA OF CONSTRUCTION F O R R E F E R E N C E O N L Y 12/2/20162:07:39PMSite Specific Philips Equipment Q2-1 11700N.MeridianStreet|Carmel,Indiana46032NorthHospitalARenovationForREV.DATE True NorthPlanNorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO.DATE 6979 12-02-16 MSKTD& Associates KEY PLAN IREquipmentReplacementAREA OF CONSTRUCTION F O R R E F E R E N C E O N L Y 12/2/20162:07:41PMSite Specific Philips Equipment Q2-2 11700N.MeridianStreet|Carmel,Indiana46032NorthHospitalARenovationForREV.DATE True NorthPlanNorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO.DATE 6979 12-02-16 MSKTD& Associates KEY PLAN IREquipmentReplacementAREA OF CONSTRUCTION F O R R E F E R E N C E O N L Y 12/2/20162:07:43PMSite Specific Philips Equipment Q2-3 11700N.MeridianStreet|Carmel,Indiana46032NorthHospitalARenovationForREV.DATE True NorthPlanNorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO.DATE 6979 12-02-16 MSKTD& Associates KEY PLAN IREquipmentReplacementAREA OF CONSTRUCTION F O R R E F E R E N C E O N L Y 12/2/20162:07:45PMSite Specific Philips Equipment Q2-4 11700N.MeridianStreet|Carmel,Indiana46032NorthHospitalARenovationForREV.DATE True NorthPlanNorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO.DATE 6979 12-02-16 MSKTD& Associates KEY PLAN IREquipmentReplacementAREA OF CONSTRUCTION F O R R E F E R E N C E O N L Y 12/2/20162:07:46PMSite Specific Philips Equipment Q2-5 11700N.MeridianStreet|Carmel,Indiana46032NorthHospitalARenovationForREV.DATE True NorthPlanNorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO.DATE 6979 12-02-16 MSKTD& Associates KEY PLAN IREquipmentReplacementAREA OF CONSTRUCTION F O R R E F E R E N C E O N L Y 12/2/20162:07:48PMSite Specific Philips Equipment Q2-6 11700N.MeridianStreet|Carmel,Indiana46032NorthHospitalARenovationForREV.DATE True NorthPlanNorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO.DATE 6979 12-02-16 MSKTD& Associates KEY PLAN IREquipmentReplacementAREA OF CONSTRUCTION F O R R E F E R E N C E O N L Y 12/2/20162:07:50PMSite Specific Philips Equipment Q2-7 11700N.MeridianStreet|Carmel,Indiana46032NorthHospitalARenovationForREV.DATE True NorthPlanNorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO.DATE 6979 12-02-16 MSKTD& Associates KEY PLAN IREquipmentReplacementAREA OF CONSTRUCTION F O R R E F E R E N C E O N L Y 12/2/20162:07:50PMSite Specific Philips Equipment Q2-8 11700N.MeridianStreet|Carmel,Indiana46032NorthHospitalARenovationForREV.DATE DOMESTIC COLD WATER DOMESTIC HOT WATER RETURN DOMESTIC HOT WATER FIRE PROTECTION NATURAL GAS SANITARY 6" DCW 6" DHW 6" DHWR 6" FP 6" NG VENT 6" S 6" V 6" SCW DOMESTIC SOFT COLD WATER ALL SYMBOLS AND ABBREVIATIONS MAY NOT BE USED ON THIS PROJECTNT CONNECTION OF NEW WORK TO EXISTING DETAIL WITH TOP LETTER INDICATING DETAIL DESIGNATION AND BOTTOM NUMBER INDICATING DRAWING THAT DETAIL IS REFERENCED ON OR DRAWING THAT DETAIL IS DRAWN ON SECTION WITH TOP NUMBER INDICATING SECTION DESIGNATION AND BOTTOM NUMBER INDICATING DRAWING THAT SECTION IS CUT ON OR DRAWING THAT SECTION IS DRAWN ON A.GENERAL NOTE 1 FLOOR PLAN SYMBOLS PLAN NOTE THERMOSTAT - "N" INDICATING NIGHT SETBACK THERMOSTAT H HUMIDISTAT 1.PLAN NOTE LIST ABBREV. A/E AC OR ACU ACCU AD ADJ AFCV AFF AFMS AHU APD APPROX AR ARCH AS ATM AV AVMS AW B BCU BDD BHP BI BLDG BOT BP BST BTU BTUH CA CAP CAV CC CCP CDS CENTRIF CFM CFOI CH CI CO CO2 COL COM COMP CONC CONN CONST CONT CP CPD CUH CW CWM CWP CWR CWS D DB DC DCV DCWBP DD DDC DE DEFL DEG DEPT DHWBP DI DIA DISC DISCH DS DSWBP DUC DWG DW DWBP DWH EA EAT EBH EC ECC ECG ED EDC EER EF EFT EG ELEC ELEV EMER EMG ENCL ENTR EOM EQA EQAC EQAI EQUIP EQV EQVP EQV V ERP ES ESP ET EUH EW EWC EWT EXH EXIST EXT F F&B F&T F/A F/SD FC FCU FD FH ABBREV. FHC FIN FLA FLR FODT FOP FOR FOS FOST FOV FP FPB FPC FPM FPS FPST FS FT FTG FTR G GA GAL GALV GC GH GPH GPM GV H HC HCP HD HE HGT HO HOA HORZ HOSP HP HPR HPS HR HRC HTR HVAC HW HWC HWCP HWP HWR HWS HX HZ IA IAC IAD ID IFB IHOM IN INCL INSUL INT INV I.P.S. ISOL JT KAIC KEC KW L LAC LAD LAN LAT LAV LBD LBS LD LF LFD LFT LOC LPR LPS LVG LVP LWT MA MAC MAD MAI MAT MAX MB MBH MC MCA MCC MD MECH MFR MH MIN MISC MOCP MPSR MPS MTD MV MVP N NA NC NIC NM NO NOM NTS O OA OAT ABBREV. OC OD OFCI OFOI OM OPER OPNG OSD P PC PD PE PF PG PHC PIV PLT POC PPH PPM PRD PREFAB PRES PRV PSI PSIG PVC RA RAD RAT R/H RD REC RECIR REF RF RG RH RHC RLA RM ROM ROP ROST RP RPG RPM RPZ REQ'D RV S SA SB SC SCC SCCH SCFM SCH SCW SD SEC SENS SEP SF SG SHT SHW SK SMBH SMC SP SPEC SQ SQFT SRV ST STD STM STR STRUCT SV SW SYS SZ T TB TCC TDH TDV TEMP THW TLL TMV TMBH TSP TW UH UNO UR UVL V VAC VAV VB VD VEL VSC VTR V V W WAGD WB W/ W/O WC WCO WFMD WG WGT WH WM WP WPD WS # DESCRIPTION ARCHITECT AND ENGINEER AIR CONDITIONING UNIT OR AIR COMPRESSOR AIR COOLED CONDENSING UNIT ACCESS DOOR ADJUSTABLE OR ADJACENT AIRFLOW CONTROL VALVE ABOVE FINISHED FLOOR AIR FLOW MEASURING STATION AIR HANDLING UNIT AIR PRESSURE DROP APPROXIMATE AIR RECEIVER ARCHITECT AIR SEPARATOR ATMOSPHERE ACID VENT AIR VOLUME MEASURING STATION ACID WASTE BOILER BLOWER COIL UNIT BACKDRAFT DAMPER BRAKE HORSEPOWER BACKWARD INCLINED BUILDING BOTTOM BRINE PUMP BULK SALT STORAGE BRITISH THERMAL UNIT BTU PER HOUR COMPRESSED AIR CAPACITY CONSTANT AIR VOLUME COOLING COIL COOLING COIL PUMP CONDENSATE PUMP DISCHARGE CENTRIFUGAL CUBIC FEET PER MINUTE CONTRACTOR FURNISHED/OWNER INSTALLED CHILLER CAST IRON CLEAN OUT CARBON DIOXIDE COLUMN CARBON DIOXIDE MANIFOLD COMPRESSOR CONCRETE CONNECTION CONSTRUCTION CONTINUOUS CONDENSATE PUMP CONDENSATE PUMP DISCHARGE CABINET UNIT HEATER COLD WATER COLD WATER MAKE-UP CHILLED WATER PUMP CHILLED WATER RETURN CHILLED WATER SUPPLY DIFFUSER OR DAMPER DECIBELS OR DRY BULB DUCT COIL DOUBLE CHECK VALVE DOMESTIC COLD WATER BOOSTER PUMP DUAL DUCT DIRECT DIGITAL CONTROL DEAERATOR DEFLECTION DEGREE DEPARTMENT DOMESTIC HOT WATER BOOSTER PUMP DEIONIZED WATER DIAMETER DISCONNECT DISCHARGE DOWNSPOUT DOMESTIC SOFT WATER BOOSTER PUMP DOOR UNDER CUT DRAWING DISTILLED WATER DOMESTIC WATER BOOSTER PUMP DOMESTIC WATER HEATER EXHAUST AIR ENTERING AIR TEMPERATURE ELECTRIC BASEBOARD HEATER ELECTRICAL CONTRACTOR ENVIRONMENTAL CONTROL CONTRACTOR EGG CRATE GRILLE EXHAUST DIFFUSER ELECTRIC DUCT COIL ENERGY EFFICIENCY RATIO EXHAUST AIR FAN ENTERING FLUID TEMPERATURE EXHAUST GRILLE OR ETHYLENE GLYCOL ELECTRIC ELEVATION EMERGENCY EXTRUDED METAL GRILLE ENCLOSURE ENTERING END OF MAIN DRIP EQUIPMENT AIR EQUIPMENT AIR COMPRESSOR EQUIPMENT AIR INTAKE EQUIPMENT EQUIPMENT VACUUM EQUIPMENT VACUUM PUMP EQUIPMENT VACUUM VENT ELECTRIC RADIANT PANEL EMERGENCY SHOWER EXTERNAL STATIC PRESSURE OR ELEVATOR SUMP PUMP EXPANSION TANK ELECTRIC UNIT HEATER EMERGENCY EYEWASH ELECTRIC WATER COOLER ENTERING WATER TEMPERATURE EXHAUST EXISTING EXTERIOR DEGREES FAHRENHEIT FACE & BYPASS FLOAT AND THERMOSTATIC TRAP FIRE ALARM FIRE AND SMOKE DAMPER FLEXIBLE CONNECTION FAN COIL UNIT FLOOR DRAIN OR FIRE DAMPER FIRE HOSE OR FUME HOOD DESCRIPTION FIRE HOSE CABINET FINISH FULL LOAD AMPS FLOOR FUEL OIL DAY TANK FUEL OIL PUMP FUEL OIL RETURN FUEL OIL SUPPLY FUEL OIL STORAGE TANK FUEL OIL VENT FIRE PROTECTION FAN POWERED BOX FIRE PROTECTION CONTRACTOR FEET PER MINUTE FEET PER SECOND FIRE PROTECTION STORAGE TANK FLOW SWITCH FEET OR FLASH TANK FOOTING OR FITTING FIN TUBE RADIATION GAS, NATURAL GAUGE GALLON GALVANIZED GENERAL CONTRACTOR GRAVITY HOOD GALLONS PER HOUR GALLONS PER MINUTE GAS NATURAL VENT HUMIDIFIER, HUMIDITY OR HEIGHT HEATING COIL HEATING COIL PUMP (HOT WATER) HEAD HEAT EXCHANGER HEIGHT HUB OUTLET HAND-OFF-AUTOMATIC HORIZONTAL HOSPITAL HORSEPOWER OR HEATPUMP HIGH PRESSURE CONDENSATE RETURN HIGH PRESSURE STEAM HOUR HEAT RECOVERY COIL HEATER HEATING, VENTILATION AND AIR CONDITIONING DOMESTIC HOT WATER DOMESTIC HOT WATER RECIRC HOT WATER CIRCULATING PUMP HEATING HOT WATER PUMP HEATING HOT WATER RETURN HEATING HOT WATER SUPPLY HEAT EXCHANGER HERTZ INSTRUMENT AIR INSTRUMENT AIR COMPRESSOR INSTRUMENT AIR DRYER, EQAD INSIDE DIAMETER OR DIMENSION INTEGRAL FACE AND BYPASS IN-HOUSE OXYGEN MANIFOLD INCHES INCLUDE INSULATED INTERIOR INVERT INTERNATIONAL PIPE SIZING ISOLATION JOINT SHORT CIRCUIT RATING KITCHEN EQUIPMENT CONTRACTOR KILOWATTS LENGTH LAB AIR COMPRESSOR LAB AIR DRYER LOCAL AREA NETWORK LEAVING AIR TEMPERATURE LAVATORY LINEAR BAR DIFFUSER POUNDS LINEAR DIFFUSER LINEAR FOOT LAMINAR FLOW DIFFUSER LEAVING FLUID TEMPERATURE LOCATION LOW PRESSURE CONDENSATE RETURN LOW PRESSURE STEAM LEAVING LAB VACUUM PUMP LEAVING WATER TEMPERATURE MEDICAL AIR MEDICAL AIR COMPRESSOR MEDICAL AIR DRYER MEDICAL AIR INTAKE MIXED AIR TEMPERATURE MAXIMUM MOP BASIN BTU/HR X 1000 MECHANICAL CONTRACTOR MINIMUM CIRCUIT AMPACITY MOTOR CONTROL CENTER MOTORIZED DAMPER MECHANICAL MANUFACTURER MANHOLE MINIMUM MISCELLANEOUS MAXIMUM OVERCURRENT PROTECTION MEDIUM PRESSURE CONDENSATE RETURN MEDIUM PRESSURE STEAM MOUNTED MEDICAL VACUUM MEDICAL VACUUM PUMP NORTH OR NITROGEN NOT APPLICABLE NORMALLY CLOSED OR NOISE CRITERIA NOT IN CONTRACT NITROGEN MANIFOLD NORMALLY OPEN, NITROUS OXIDE, OR NUMBER NOMINAL OR NITROUS OXIDE MANIFOLD NOT TO SCALE OXYGEN OUTSIDE AIR OUTSIDE AIR TEMPERATURE DESCRIPTION ON CENTER OUTSIDE DIAMETER OWNER FURNISHED/CONTRACTOR INSTALLED OWNER FURNISHED/OWNER INSTALLED OXYGEN MANIFOLD OPERATOR OPENING OPEN SITE DRAIN PUMP, PNEUMATIC OR PRESSURE PLUMBING CONTRACTOR PRESSURE DROP OR PERFORATED DIFFUSER PNEUMATIC ELECTRIC PREFILTERS PROPYLENE GLYCOL PREHEAT COIL POST INDICATOR VALVE PLASTER TRAP POINT OF CONNECTION POUNDS PER HOUR PARTS PER MILLION PRESSURE RELIEF DOOR PREFABRICATED PRESSURE PRESSURE REDUCING VALVE POUNDS PER SQUARE INCH POUNDS PER SQUARE INCH GAUGE POLYVINYL CHLORIDE RETURN AIR OR RELIEF AIR RADIATED RETURN AIR TEMPERATURE REHEAT ROOF DRAIN RECEIVER RECIRCULATING REFRIGERATOR RETURN AIR FAN RETURN GRILLE RELIEF HOOD OR RELATIVE HUMIDITY REHEAT COIL RUNNING LOAD AMPS ROOM REVERSE OSMOSIS VENT REVERSE OSMOSIS PUMP REVERSE OSMOSIS STORAGE TANK RADIANT PANELS RETURN PERFORATED GRILLE REVOLUTIONS PER MINUTE REDUCED PRESSURE BACKFLOW REQUIRED ROOF VENTILATOR SANITARY OR SEWER SUPPLY AIR OR SOUND ATTENUATOR STEAM BOILER STEAM COIL STEAM CONDENSATE COOLER SUBCOOLED CHILLER STANDARD CUBIC FEET PER MINUTE SCHEDULE SOFT COLD WATER (DOMESTIC) SUPPLY DIFFUSER OR SMOKE DAMPER SECTION SENSIBLE SEWAGE EJECTOR PUMP SUPPLY AIR FAN SUPPLY GRILLE SHEET SOFT HOT WATER SINK SENSIBLE MBH SHEET METAL CONTRACTOR STATIC PRESSURE OR STORM PUMP SPECIFICATIONS SQUARE SQUARE FEET SAFETY RELIEF VALVE STEAM TRAP STANDARD STORM STARTER STRUCTURAL STEAM VENT SWITCH SYSTEM SPRINKLER ZONE THERMOSTAT TERMINAL BOX TEMPERATURE CONTROL CONTRACTOR TOTAL DISCHARGE HEAD TRIPLE DUTY VALVE TEMPERATURE TEMPERED HOT WATER TEMPERATURE LOW LIMIT THERMOSTAT MIXING VALVE TOTAL MBH TOTAL STATIC PRESSURE TEMPERED WATER UNIT HEATER UNLESS NOTED OTHERWISE URINAL ULTRA VIOLET LIGHT VENT VACUUM VARIABLE AIR VOLUME VACUUM BREAKER VOLUME DAMPER (MANUAL) VELOCITY VARIABLE SPEED CONTROLLER VENT THROUGH ROOF VACUUM VENT WASTE, WATTS OR WIDTH WASTE ANESTHESIA GAS DISPOSAL PUMP WET BULB WITH WITHOUT WATER CLOSET OR WATER COLUMN WALL CLEAN OUT WATER FLOW MEASURING DEVICE WATER GAUGE WEIGHT WALL HYDRANT WATER METER WEATHERPROOF WATER PRESSURE DROP WATER SOFTENER POUND ACD AIR CONDITIONING CONDENSATE DRAIN MECHANICAL AND PLUMBING ABBREVIATIONS PLUMBING PIPING SYMBOLSVALVE AND FITTING SYMBOLS CALIBRATED BALANCE VALVE PIPING FLEXIBLE CONNECTION PIPE TURNED UP (UNLESS NOTED OTHERWISE) PIPE TURNED DOWN PIPE OUT TOP PIPE OUT BOTTOM THREADED NIPPLE W/CAP PIPE WITH BLIND FLANGE CONCENTRIC REDUCER ECCENTRIC REDUCER CHECK VALVE UNION GATE VALVE BALL VALVE GLOBE VALVE BUTTERFLY VALVE TEMPERATURE CONTROL - 2 WAY MODULATING VALVE TEMPERATURE CONTROL - 2 WAY 2 POSITION MODULATING VALVE TEMPERATURE CONTROL - 3 WAY MODULATING VALVE TEMPERATURE CONTROL - 3 WAY 2 POSITION MODULATING VALVE SAFETY RELIEF VALVE STRAINER FLOW METER FLOOR DRAIN ZONE CONTROL VALVE (OS&Y) AUTOMATIC FLOW CONTROL VALVE FLOW MEASURING DEVICE MANUAL AIR RELIEF VENT AUTOMATIC AIR RELIEF VENT LUBRICATED PLUG VALVE STEAM PRESSURE REDUCING VALVE ANGLE VALVE GAS PRESSURE RELIEF VALVE REFRIGERANT HOT GAS BY-PASS VALVE SHUT-OFF COCK (HYDRONICS) SOLENOID VALVE REFRIGERANT EXPANSION VALVE WATER PRESSURE REDUCING/REGULATING VALVE COMBINATION WATER PRESSURE RELIEF AND REDUCING VALVE STEAM TRAP DIELECTRIC UNION BETWEEN STEEL AND COPPER STRAINER (STEAM) PRESSURE AND TEMPERATURE PLUG REFRIGERANT SIGHT GLASS THERMOMETER (P=PRESS V=VAC T=TEMP) GAUGE SENSOR (T-TEMP H-HUMIDITY) FLOW SWITCH CLEAN OUT WATER HAMMER ARRESTOR OR ALARM PRESSURE/VACUUM SWITCH INDICATED EXPANSION LOOP (COLD SPRUNG) ANCHOR GUIDE REDUCED PRESSURE BACKFLOW PREVENTER ATMOSPHERIC VACUUM BREAKER PRESSURE VACUUM BREAKER REFRIGERANT SHUT-OFF VALVE DOMESTIC WATER TEMPERATURE REGULATING VALVE EXPANSION JOINT DIFFERENTIAL SWITCH∆T P A T T A NO NC NO NC DETAIL VIEWPLAN VIEWS A101 1 TYP 1 A101 TYP TAGS V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 V11 V12 V13 V14 V15 V16 V17 V18 V19 V20 V21 V22 V23 V24 V25 V26 V27 V28 V29 V30 V31 V32 V33 V34 V35 V36 V37 V38 V39 V40 V41 V42 V43 V44 V45 V46 V47 V48 V49 V50 V51 V52 V53 V54 V55 V56 V57 V58 V59 V60 TYP TYPICAL CV CENTRAL VACUUM CENTRAL VACUUM OUTLETV61 GENERAL NOTES 1.ALL CONTRACT DOCUMENTS (SPECIFICATIONS AND DRAWINGS) ARE COMPLIMENTARY AND MUST BE USED IN COMBINATION TO OBTAIN COMPLETE CONSTRUCTION INFORMATION. 2.ALL CONFLICTS SHALL BE BROUGHT TO THE ARCHITECTS OR ENGINEERS ATTENTION IN ORDER TO ALLOW A CLARIFICATION TO BE ISSUED. ANY WORK COMPLETED WITHOUT THE CLARIFYING INFORMATION IS AT THE CONTRACTORS FINANCIAL RISK. 3.THE CONTRACTOR SHALL PROVIDE AND FURNISH ALL MATERIALS AND ACCESSORIES TO CREATE A FULLY OPERATIONAL, CODE COMPLIANT AND TESTED SYSTEM. ALL MATERIALS AND ACCESSORIES REQUIRED TO CREATE THE FULLY OPERATIONAL SYSTEM SHALL BE INCLUDED IN THE COST OF THIS PROJECT. 4.THESE DRAWINGS ARE DIAGRAMMATIC IN NATURE. THE CONTRACTOR MAY AT THEIR OPTION MODIFY THE PIPE ROUTING IN ORDER TO CREATE A SYSTEM THAT MEETS THE INTENT OF THIS SET OF CONSTRUCTION DOCUMENTS. 5.THE CONTRACTOR SHALL INCLUDE ALL ITEMS THAT ARE REQUIRED TO ENSURE THAT THE ENTIRE SYSTEM IS FUNCTIONING IN COMPLIANCE WITH THE APPLICABLE CODES, AND MANUFACTURES INSTALLATION RECOMMENDATIONS AND OR REQUIREMENTS. 6.ALL CUTTING, DRILLING AND PATCHING OF WALLS, FLOORS AND/OR STRUCTURAL MEMBERS FOR THE INSTALLATION OF THE PLUMBING AND FIRE PROTECTION SYSTEMS SHALL BE PROVIDED AS PART OF THE SCOPE OF THIS PROJECT. 7.STRUCTURAL COMPONENTS SHALL NOT BE CUT, DRILLED OR MODIFIED IN ANY WAY WITHOUT THE STRUCTURAL ENGINEERS REVIEW AND PRIOR WRITTEN APPROVAL. 8.PROVIDE FIRE STOPPING WHERE PIPES PENETRATE FIRE RATED FLOORS AND WALLS. FIRE STOPPING MATERIALS AND METHODS SHALL BE PER LOCAL AND STATE CODES AND REQUIREMENTS. 9.ALL PLUMBING SYSTEMS SHALL BE INSTALLED PER THE CURRENT PLUMBING CODE FOR THE LOCATION OF THE WORK BEING INSTALLED. 10.ALL PLUMBING EQUIPMENT, PIPING, FIXTURES, AND PIPE ACCESSORIES SHALL BE NSF 61, ANNEX G COMPLIANT. 11.ALL PIPING LOCATED WITHIN A RETURN AIR PLENUM SHALL COMPLY WITH A 25/50 FLAME SMOKE RATING. ANY EXISTING PIPING DISCOVERED WITHIN A RETURN AIR PLENUM THAT DOES NOT COMPLY WITH THIS REQUIREMENT SHALL BE BROUGHT TO THE ATTENTION OF THE ARCHITECT FOR FURTHER CLARIFICATION. 12.ALL EXTERIOR WALL PENETRATIONS SHALL BE SEALED WATER AND WEATHER TIGHT BY THE APPROPRIATE TRADE COMPETENT IN COMPLETING THIS WORK. THE COST OF THIS WORK SHALL BE INCLUDED IN THE SCOPE OF THIS PROJECT. 13.ALL VENT THROUGH ROOF (VTR) LOCATIONS SHALL BE FIELD VERIFIED IN REGARDS TO ANY OUTDOOR INTAKE. LOCATION OF VTR SHALL BE NO LESS THAN AS REQUIRED BY THE LOCAL OR STATE CODES. 14.DO NOT ATTACH ANY CONSTRUCTION TO THE ROOF DECK JOIST BRIDGING, JOIST CROSS BRACING, PIPING, CONDUIT, DUCTWORK OR ANY OTHER NON-STRUCTURAL ITEM. 15. DO NOT WELD OR DRILL INTO STRUCTURAL STEEL OR JOIST; INSTEAD USE CLAMPS, TIE WIRE, THRU-BOLTS WITH WASHERS 16.DO NOT USE ANY PVC, PLASTIC, ETC. IN PLENUM OR DEMISING WALLS UNLESS FIRE WRAPPED. ALL WOOD BLOCKING AND NAILERS, CONCEALED OR NOT SHALL BE FIRE RETARDANT TREATED. 17.DO NOT PENETRATE BUILDING WALLS FOR ANY DUCTING OR VENTING; ROUTE THROUGH ROOF USING LANDLORDS ROOFING CONTRACTOR. 18.VENT THROUGH ROOF INSTALLATION; ALL ROOFING WORK SHALL BE COMPLETED BY THE LANDLORDS ROOFING CONTRACTOR. THE COST SHALL BE INCLUDED IN THE SCOPE OF THIS PROJECT. 19.PIPING BELOW GROUND SHALL BE SERVICE-WEIGHT CAST IRON OR SCHEDULE 40 PVC. NO- HUB PIPING OR FERNCO CONNECTIONS ARE NOT PERMITTED BELOW GRADE. 20 DOMESTIC WATER PIPING ABOVE GRADE SHALL BE TYPE "L" WATER TUBE. 21.ALL PIPING SHALL BE PROPERLY SUSPENDED BY THE STRUCTURE PER THE LOCAL CODES. 22.NO SANITARY WASTE OR VENT, HOT OR COLD WATER SHALL BE ALLOWED TO BE INSTALLED IN THE DEMISING WALLS. 23.ALL PIPING INSULATED SHALL BE WITH PLENUM RATED MATERIALS. 24.FLOOR DRAINS SHALL BE PROVIDED WITH TRAP PRIMERS. 25.GAS PIPING SUPPORTED ON THE ROOF SHALL BE PROVIDED FREE FLOATING PREFABRICATED SUPPORTS OR EQUIPMENT SUPPORTS WITH ROLLER ASSEMBLIES. WOOD SUPPORTS WILL NOT BE PERMITTED. 26.ALL GAS PIPING SHALL BE PROVIDED PIPE LABELS IDENTIFYING THE GAS PRESSURE. 27.ALL GAS PIPING SHALL BE INSTALLED PER THE LOCAL CODES FOR MATERIALS AND INSTALLATIONS REQUIREMENTS. 28.ALL SHUT-DOWN OF UTILITIES AND FIRE PROTECTION SYSTEMS SHALL BE ARRANGED WITH NO LESS THAN SEVEN (7) DAYS NOTICE TO THE LANDLORD. WORK MAY NOT COMMENCE UNLESS WRITTEN APPROVAL IS PROVIDED BY THE LANDLORD. 29.ALL DOMESTIC WATER BRANCH PIPES SERVING FIXTURES OR EQUIPMENT WITH FAST ACTING OR ELECTRONIC VALVES SHALL BE PROVIDED WATER HAMMER ARRESTORS. 30.ALL BRANCH PIPES FROM DOMESTIC WATER MAINS SHALL BE PROVIDED QUARTER TURN FULL PORT BALL VALVES ON THE BRANCH PIPE JUST ADJACENT TO THE MAIN. Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:08:08 PMPlumbing Symbols and Abbreviations P001 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation ForREV. DATE Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:08:20 PMPlumbing Specifications P002 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation ForREV. DATE 14.9 15 16 16.1 K L1/2" O1/2" MA3/4" MV3/4" NO23/4" WAGD1/2" O 1/2" MA 3/4" MV 3/4" NO2 3/4" WAGD 1/2" O1/2" MA3/4" MV1/2" NO23/4" WAGD1/2" O 1/2" MA 3/4" MV 3/4" NO2 3/4" WAGD 5 7 8 9 EXISTING CATH SUITE MEDICAL GAS MAINS 14.9 15 16 16.1 K L 1/2" O 1/2" MA 3/4" MV 3/4" NO2 3/4" WAGD 1/2" O 1/2" MA 3/4" MV 1/2" NO2 3/4" WAGD WAGD NO2 MV MA O WAGD NO2 MV MA O NO2MAO3/4" WAGD12 3 4 6 3/4" WAGD 3/4" NO2 3/4" MV 1/2" MA 1/2" O EXISTING MED GAS ALARM WIRING TO REMAIN. EXISTING MED GAS ALARM PANEL LOCATED IN BN103 TO REMAIN. EXISTING MED GAS ALARM SWITCHES TO REMAIN. EXISTING MED GAS OUTLETS TO REMAIN. 2 - MA 2 - O2 2 - MV 1 - NO2 1 - WAGD EXISTING MEDICAL GAS AREA SHUT-OFF VALVES 1 - MA 1 - 02 1 - MV 1 - N02 1 - WAGD 1/2" O 1/2" MA 3/4" MV 1/2" NO2 3/4" WAGD MEDICAL GAS TO NEW FLOOR PEDESTAL. COORDINATE AND CONNECT MEDICAL GAS PIPE WITH PEDESTAL CONFIGURATION AND REQUIREMENTS. FIRESTOP PENETRATIONS AS REQUIRED TO MAINTAIN EXISTING FIRE RATINGS. MEDICAL GAS DOWN TO LOWER LEVEL. FIRESTOP FLOOR PENETRATIONS AS REQUIRED TO MAINTAIN FLOOR RATINGS. AREA OF CONSTRUCTION True NorthPlan NorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates KEY PLAN IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:08:31 PMFirst Floor Plumbing Plans P210 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation For 1/4" = 1'-0"1 First Floor Plumbing Demolition Plan 1/4" = 1'-0"2 Frist Floor Medical Gas Plan PLAN NOTES 1 NEW 1/2" 02, 1/2" MA, 3/4" MV, 1/2 NO2, AND 3/4" WAGD DOWN TO BASEMENT. ROUTE MEDICAL GAS PIPING TO FLOOR MOUNTED PEDESTAL. 2 NEW 1/2" 02, 1/2" MA, 3/4" MV, 1/2 NO2, AND 3/4" WAGD UP FROM BASEMENT TO FLOOR MOUNTED PEDESTAL. 3 EXISTING MED GAS ZONE VALVES SERVING B168. 4 EXISTING MED GAS OUTLETS TO REMAIN. 5 THE EXISTING FIRE SPRINKLER SYSTEM LOCATED WITHIN THIS ROOM SHALL BE REMOVED COMPLETE, INCLUDING ALL MAINS, BRANCH PIPE, AND ARM OVERS AS REQUIRED TO ACCOMMODATE ALL NEW CEILINGS, EQUIPMENT, DUCTWORK, LIGHTING, AND ALL OTHER NEW WORK. 6 ALL SPRINKLER HEADS SHALL BE PLACED IN THE CEILING SYSTEM IN A FASHION THAT ENSURE COVERAGE OF THE ROOM IN A CODE COMPLIANT MANNER. COORDINATE SPRINKLER HEAD LOCATION WITH ALL OTHER UTILITIES AND CEILING MOUNTED CATH LAB EQUIPMENT. 7 EXISTING MED GAS ALARM CONDUIT TO REMAIN. 8 EXISTING MED GAS ALARM PANEL LOCATED IN NURSE STATION BN103 TO REMAIN. 9 EXISTING MED GAS ALARM SWITCHES TO REMAIN. 3 MED GAS ISOMETRIC REV. DATE ALL SYMBOLS AND ABBREVIATIONS MAY NOT BE USED ON THIS PROJECTT SENSOR (T=TEMP H=HUMIDITY) (P=PRES V=VAC T=TEMP) GAUGE THERMOMETER PRESSURE AND TEMPERATURE PLUG WATER PRESSURE REDUCING/REGULATING VALVE AUTOMATIC AIR VENT MANUAL AIR VENT FLOOR DRAIN FLOW METER CLEANOUT TEMPERATURE CONTROL 3-WAY 2-POSITION VALVE MECHANICAL VALVE AND FITTING SYMBOLS DESCRIPTIONSYMBOL TEMPERATURE CONTROL 2-WAY MODULATING VALVE TEMPERATURE CONTROL 2-WAY 2-POSITION VALVE TEMPERATURE CONTROL 3-WAY MODULATING VALVE CALIBRATED BALANCING VALVE PIPING FLEXIBLE CONNECTION PIPE TURNED UP (UNLESS NOTED OTHERWISE) PIPE TURNED DOWN PIPE OUT TOP PIPE OUT BOTTOM THREADED/FLANGED CAP CONCENTRIC REDUCER CHECK VALVE UNION STRAINER SAFETY RELIEF VALVE BUTTERFLY VALVE BALL VALVE GATE VALVE PLAN VIEW DETAIL VIEW R OR D FD SD F/SD MD DESCRIPTIONSYMBOLDESCRIPTION MECHANICAL DUCTWORK SYMBOLS SYMBOL WITH FLEX DUCT SECTION PLAN VIEW STANDARD RADIUS ELBOW WITH CENTER RADIUS EQUAL TO 1-1/2 TIMES WIDTH OF DUCT UNLESS OTHERWISE INDICATED FLAT OVAL SPIRAL DUCT (FIRST DIMENSION, SIDE SHOWN) RECTANGULAR DUCT (FIRST DIMENSION, SIDE SHOWN) SPIN-IN FITTING WITH MANUAL VOLUME DAMPER AND FLEXIBLE DUCT CONNECTION TYPICAL TERMINAL UNIT WITH REHEAT COIL GRILLE/REGISTER/DIFFUSER CONNECTION SIDEWALL SUPPLY, RETURN OR EXHAUST GRILLE DIFFUSER (NO AIRFLOW IN SHADED DIRECTION) INSULATED METAL PANEL 45 DEGREE LATERAL (ROUND OR FLAT OVAL ONLY) 90 DEGREE TEE (ROUND OR FLAT OVAL ONLY) SQUARE-TO-ROUND TRANSITION CONICAL FITTING ROUND SPIRAL DUCT 90 DEGREE ELBOW WITH TURNING VANES FLEXIBLE CONNECTION BEVELED ENTRY FITTING MANUAL VOLUME DAMPER FIRE DAMPER WITH ACCESS DOOR SMOKE DAMPER WITH ACCESS DOOR FIRE/SMOKE DAMPER WITH ACCESS DOOR DUCT TURNED UP (SOLID LINES) DUCT TURNED DOWN (DASHED LINES) R(RISE), D(DROP) SUPPLY DIFFUSER OR SUPPLY GRILLE RETURN GRILLE EXHAUST GRILLE SUPPLY, RETURN, OR EXHAUST SLOT DIFFUSER W" X H"DIA"ø AUTOMATIC MOTOR OPERATED DAMPER W "X H"ø DIA"ø W" X H" CD CPD CHWR CR CS CHWS HWS HWR DIRECTION OF PIPE SLOPE (DOWN) CONDENSATE & EQUIPMENT DRAIN CONDENSATE PUMP DISCHARGE CONDENSER WATER RETURN CONDENSER WATER SUPPLY CHILLED WATER RETURN CHILLED WATER SUPPLY HEATING WATER RETURN HEATING WATER SUPPLY HVAC PIPING SYMBOLS LINE SYMBOLS SCREENED LINES INDICATE EXISTING TO REMAIN HEAVY CONTINUOUS LINES INDICATE NEW WORK HEAVY DASHED LINES INDICATE EXISTING TO BE REMOVED AD ACCESS DOOR Ø °F A/E ACC ACCU AD ADJ AFCV AFF AFMS AGA AHU AL ANSI AO AP APD ARI AS ASHRAE ASME ASPE ASTM ATM AUTO AWWA B BCU BD BDD BHP BI BOD BOP BTUH CA CAP CAV CB CD CO2 CFM CH CHWP CHWR CHWS CO COMP COND CONV CP CPD CR CS CT CUH CWP dB DD DDC DEG DIA DISC DWH DWV DX EA EAT EC ECG EDR EER EF EFF EFT EG EMG EOM ESP ET EWT EXH F F&T FCO FCU FD FM FPB FPM FPS PHASE DEGREES FAHRENHEIT ARCHITECT/ENGINEER AIR COOLED CONDENSER AIR COOLED CONDENSING UNIT AREA DRAIN, ACCESS DOOR ADJUSTABLE, ADJACENT AIRFLOW CONTROL VALVE ABOVE FINISHED FLOOR AIRFLOW MEASURING STATION AMERICAN GAS ASSOCIATION AIR HANDLING UNIT ALUMINUM AMERICAN NATIONAL STANDARDS INSTITUTE ANALOG OUTPUT ACID PROOF, ACCESS PANEL AIR PRESSURE DROP (IN. WC) AIR CONDITIONING REFRIGERATION INSTITUTE AIR SEPARATOR AMERICAN SOCIETY OF HEATING, REFRIGERATION, AND AIR CONDITIONING ENGINEERS AMERICAN SOCIETY OF MECHANICAL ENGINEERS AMERICAN SOCIETY OF PLUMBING ENGINEERS AMERICAN SOCIETY FOR TESTING AND MATERIALS ATMOSPHERE AUTOMATIC AMERICAN WATER WORKS ASSOCIATION BOILER BLOWER COIL UNIT BALANCE DAMPER BACK-DRAFT DAMPER BRAKE HORSEPOWER OR BOILER HORSEPOWER BINARY INPUT, BACKWARD INCLINED BOTTOM OF DUCT BOTTOM OF PIPE BRITISH THERMAL UNITS PER HOUR COMPRESSED AIR CAPACITY CONSTANT AIR VOLUME CATCH BASIN OR CHILLED BEAM CONDENSATE DRAIN CARBON DIOXIDE CUBIC FEET PER MINUTE CHILLER CHILLED WATER PUMP CHILLED WATER RETURN CHILLED WATER SUPPLY CLEANOUT COMPRESSOR CONDENSER CONVECTOR CONDENSATE PUMP CONDENSATE PUMP DISCHARGE CONDENSER WATER RETURN CONDENSER WATER SUPPLY COOLING TOWER CABINET UNIT HEATER CONDENSER WATER PUMP DECIBEL DUAL DUCT DIRECT DIGITAL CONTROL DEGREE (°F) DIAMETER DISCONNECT SWITCH DOMESTIC WATER HEATER DRAIN, WASTE, AND VENT DIRECT EXPANSION EXHAUST AIR ENTERING AIR TEMPERATURE (°F) ELECTRICAL CONTRACTOR EGG-CRATE GRILLE EQUIVALENT DIRECT RADIATION ENERGY EFFICIENCY RATIO EXHAUST FAN EFFICIENCY ENTERING FLUID TEMPERATURE (°F) EXHAUST GRILLE EXTRUDED METAL GRILLE (WELDED WIRE MESH) END OF MAIN DRIP EXTERNAL STATIC PRESSURE (IN. WC.) EXPANSION TANK ENTERING WATER TEMPERATURE (°F) EXHAUST FURNACE FLOAT AND THERMOSTATIC STEAM TRAP FLOOR CLEANOUT FAN COIL UNIT FLOOR DRAIN FACTORY MUTUAL FAN POWERED TERMINAL UNIT FEET PER MINUTE FEET PER SECOND ABBREVIATIONS AND TERMS FLOOR SINK FIRE/SMOKE DAMPER FINNED TUBE RADIATION GAGE OR GUAGE GALLON GENERAL CONTRACTOR GALLONS PER DAY GALLONS PER HOUR GALLONS PER MINUTE HEAD (FT.) HORSEPOWER HIGH PRESSURE STEAM RETURN HIGH PRESSURE STEAM SUPPLY HOT WATER PUMP HEATING WATER RETURN HEATING WATER SUPPLY HEAT EXCHANGER INTEGRAL FACE/BYPASS LEAVING AIR TEMPERATURE (°F) LOW PRESSURE STEAM RETURN LOW PRESSURE STEAM SUPPLY LEAVING WATER TEMPERATURE (°F) MIXED AIR MIXED AIR TEMPERATURE (°F) THOUSAND BTU PER HOUR MECHANICAL CONTRACTOR MINIMUM CIRCUIT AMPACITY MOTOR CONTROL CENTER MOTORIZED DAMPER MEDIUM PRESSURE STEAM RETURN MEDIUM PRESSURE STEAM SUPPLY NOISE CRITERIA, NORMALLY CLOSED NATIONAL ELECTRIC CODE NATIONAL FIRE CODE NATIONAL FIRE PROTECTION ASSOCIATION NOT IN CONTRACT NORMALLY OPEN NOT TO SCALE OUTSIDE AIR OUTSIDE AIR TEMPERATURE (°F) OPPOSED BLADE DAMPER OUTSIDE DIAMETER OWNER FURNISHED/CONTRACTOR INSTALLED PUMP PLUMBING CONTRACTOR PRESSURE DROP PRE-FILTER PROPYLENE GLYCOL WATER PREHEAT COIL PARTS PER MILLION PRESSURE REDUCING VALVE POUNDS PER SQUARE INCH POUNDS PER SQUARE INCH (ABSOLUTE) POUNDS PER SQUARE INCH (GAUGE) PACKAGED TERMINAL AIR CONDITIONER RETURN AIR RETURN AIR TEMPERATURE (°F) RETURN FAN RETURN GRILLE RELATIVE HUMIDITY REHEAT COIL RADIANT PANEL ROOFTOP UNIT SUPPLY AIR SUPPLY AIR TEMPERATURE (°F) SUPPLY DIFFUSER SEASONAL ENERGY EFFICIENCY RATIO SUPPLY GRILLE SHEETMETAL AND AIR CONDITIONING CONTRACTORS ASSOCIATION STATIC PRESSURE SUPPLY REGISTER SAFETY RELIEF VALVE STEAM VENT THERMOSTAT TEMPERATURE CONTROL CONTRACTOR TEMPERATURE DIFFERENCE TOTAL STATIC PRESSURE THERMAL EXPANSION VALVE TYPICAL UNIT HEATER UNDERWRITER'S LABORATORIES VARIABLE AIR VOLUME VOLUME DAMPER VARIABLE FREQUENCY CONTROLLER (SAME AS VFD, VSC) VARIABLE FREQUENCY DRIVE (SAME AS VFC, VSC) VARIABLE SPEED CONTROLLER (SAME AS VFC, VFD) WITH WITHOUT WET BULB TEMPERATURE (°F) WATER PRESSURE DROP (FT. HD) WATER SOURCE HEAT PUMP FS FSD FTR GA GAL GC GPD GPH GPM HD HP HPR HPS HWP HWR HWS HX IFB LAT LPR LPS LWT MA MAT MBH MC MCA MCC MD MPR MPS NC NEC NFC NFPA NIC NO NTS OA OAT OBD OD OF/CI P PC PD PF PGW PHC PPM PRV PSI PSIA PSIG PTAC RA RAT RF RG RH RHC RP RTU SA SAT SD SEER SG SMACNA SP SR SRV SV T TCC TD TSP TXV TYP UH UL VAV VD VFC VFD VSC W/ W/O WB WPD WSHP ECCENTRIC REDUCER GLOBE VALVE T STEAM TRAP VACUUM BREAKER GENERAL MECHANICAL DEMOLITION NOTES A.CONTRACTOR TO FIELD VERIFY EXISTING DUCTWORK LOCATION, SIZE, AND ELEVATION PRIOR TO REMOVAL. COORDINATE ANTICIPATED ROUTING WITH EXISTING AND NEW DUCTWORK, PIPING, AND CONDUITS. CONTACT ENGINEER IF FIELD CONDITIONS REQUIRE ALTERNATIVE ROUTING. VERIFY THAT ALL SERVICES TO BE REMOVED DO NOT SERVE AREAS OUTSIDE INDICATED SCOPE OF WORK. B.PIPE AND DUCT ROUTINGS AND CLEARANCES INDICATED ARE BASED ON BEST AVAILABLE INFORMATION. CONTRACTOR SHALL VERIFY PIPING, DUCTWORK, ELECTRICAL, AND STRUCTURAL DETAILS OF EXISTING AND NEW INSTALLATIONS DURING AND AFTER DEMOLITION (PRIOR TO NEW INSTALLATIONS) TO DETERMINE WORK NECESSARY TO INSTALL WORK AS SHOWN AND INTENDED. CONTRACTOR SHALL CONTACT THE ENGINEER WITH ANY CONCERNS UPON COMPLETION OF THIS EFFORT. C.COORDINATE OUTAGES WITH OTHER CONTRACTORS, OWNER, AND MAINTENANCE STAFF. PROVIDE SUFFICIENT ADVANCE SCHEDULING TO MEET OCCUPANTS AND FACILITY PERSONNELS REQUIREMENTS FOR PLANNING AND COORDINATING FOR SYSTEMS WHICH MAY NOT BE EASILY INTERRUPTED. D.WHERE MECHANICAL, ELECTRICAL, PLUMBING, AND FIRE PROTECTION WORK IS DETERMINED TO PENETRATE EXISTING FLOORS, WALLS, CEILING, OR ROOF, THE OPENING THROUGH WHICH THE ABOVE DESCRIBED ITEM IS TO PASS MUST BE REPAIRED OR BUILT BACK BY THE CONSTRUCTION TRADE SKILLED IN THE WORK TO BE PERFORMED. SUBCONTRACTOR SHALL BE RESPONSIBLE FOR PROCURRING THE SERVICES OF SKILLED CONTRACTOR. E.PROVIDE TEMPORARY PATCHING AS REQUIRED FOR INFECTION CONTROL AS DETERMINED BY HOSPITAL INFECTION CONTROL DEPARTMENT AND MAINTAIN EXISTING FIRE AND SMOKE RATINGS. F.WHERE PRE-DEMOLITION AIRFLOW READINGS ARE NOTED, TAKE READINGS PRIOR TO BEGINNING ANY DEMOLITION WORK OR CONSTRUCTING NEGATIVE AIR PRESSURE BARRIERS. PRE-DEMOLITION TAB WORK WILL LIKELY OCCUR AFTER NORMAL HOURS, CONFIRM WITH OWNER. G.ALL DUCTWORK, PIPING, AND EQUIPMENT INDICATED BY DASHED LINETYPE SHALL BE REMOVED AS DESCRIBED BY PLAN NOTES. REMOVE OR REUSE ASSOCIATED HANGERS. DO NOT LEAVE UNUSED EQUIPMENT ABANDONED ABOVE CEILING. ALL TERMINAL UNITS TO BE REMOVED SHALL ALSO HAVE SUPPLY DUCTS REMOVED BACK TO MAIN DUCTS AS INDICATED AND CAP SUITABLE FOR +4" W.G. REMOVE PIPING RUNOUTS BACK TO MAIN AND CAP. FOR PIPING RUNOUTS THAT ARE TO BE REUSED, REMOVE ALL CONTROL VALVES, BALANCE VALVES, STRAINERS , AND PIPING ACCESSORIES TO BRANCH SHUT-OFF VALVES. REMOVE PNEUMATIC CONTROL TUBING BACK TO MAIN AND CAP. ALL TUBING LEFT UNNECESSARY AND OBSOLETE SHALL BE REMOVED BACK TO MAIN SOURCE AND CAPPED. ALL TUBING SERVING AREAS OUTSIDE OF THE PROJECT SCOPE SHALL BE LEFT FUNCTIONAL. ALL EXISTING TERMINAL UNITS, DDC CONTROLLERS, ROOM PRESSURE MONITORS, AND HARDWARE TO BE REMOVED SHALL BE DONE SO IN A MANNER TO MINIMIZE DAMAGE AND OFFERED TO THE OWNER. CONTRACTOR SHALL DISCARD ALL DEVICES NOT WISHED TO BE RETAINED BY THE OWNER. GENERAL MECHANICAL NOTES A.REFER TO SCHEDULES FOR DIFFUSER AND TERMINAL UNIT RUNOUT SIZES. B.UNLESS NOTED OTHERWISE, TERMINAL UNIT DISCHARGE DUCT SHALL BE THE SAME SIZE AS THE TERMINAL UNIT DISCHARGE CONNECTION. PROVIDE TRANSITIONS TO EXISTING DUCTWORK AS REQUIRED. C.LOCATE ALL TERMINAL UNITS, DAMPERS, VALVES, AND EQUIPMENT REQUIRING ACCESS IN AN UNOBSTRUCTED LOCATION ABOVE LAY-IN CEILING. COORDINATE THE INSTALLATION OF A CEILING ACCESS PANEL WITH GENERAL CONTRACTOR. D.FIELD VERIFY LOCATION OF ALL FLOOR PENETRATIONS PRIOR TO CUTTING TO ASSURE THAT NO FLOOR PENETRATION CONFLICTS WITH EXISTING BEAMS OR JOISTS. FLOOR PENETRATIONS SHALL BE ONLY THROUGH THE SLAB. DO NOT CUT THROUG BEAMS OR JOISTS. NOTIFY ARCHITECT AND ENGINEER FOR ANY REQUIRED MODIFICATIONS PRIOR TO CUTTING. E.REFER TO TERMINAL UNIT SCHEDULE FOR PIPE RUNOUT SIZES. F.MINIMUM PIPE SIZE SHALL NOT BE LESS THAN 3/4". G.ALL NEW AIR-HANDLING SYSTEMS AND ASSOCIATED DISTRIBUTION SHALL COMPLY WITH NFPA-90A-2012. H.ALL DUCTWORK AND PIPE INSULATION SHALL BE INSTALLED CONTINUOUSLY THROUGH WALLS. OPENINGS SHALL BE FRAMED LARGE ENOUGH TO ACCOMMODATE INSULATED PIPE/DUCT. ALLOW ENOUGH ANNULAR SPACE FOR PROPER SEALANT. NON-RATED WALLS SHALL HAVE NON-COMBUSTIBLE SEALANT. RATED BARRIERS SHALL HAVE A UL-LISTED FIRESTOPPING ASSEMBLY. INSTALL FIRESTOPPING ASSEMBLY IN COMPLIANCE WITH MANUFACTURER'S WRITTEN INSTALLATION INSTRUCTIONS AND IN COMPLIANCE WITH UL- LISTED ASSEMBLY. I.WHERE EXISTING DUCTWORK IS INDICATED AS EXISTING TO BE REUSED, INSPECT DUCT INSULATION AND REPAIR AS REQUIRED FOR A LIKE-NEW INSTALLATION. Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:07:09 PMMechanical Symbols and Abbreviations M001 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation ForREV. DATE Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:07:19 PMMechanical Specifications M002 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation ForREV. DATE Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:07:32 PMMechanical Specifications M003 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation ForREV. DATE 14.9 15 16 16.1 K L (TYP. 5) LFD2-250 (TYP. 5) TU-B168 TU-B167A ETU-B167AFCV-B168 SG1-650 RG1-650 9 8 WRG1-675WRG1-675 10 11 12 12 M700 1 M700 4 M700 5 M700 2 (TYP.) (TYP.) (TYP.) M700 3 (TYP) LFD1-125 14.9 15 16 16.1 K L 1 2 (TYP) 3 T 4 5 5 6 7 T 17 14.9 15 16 16.1 K L TU-B168 TU-B167A ETU-B167AFCV-B168 ∆P 13 TC 14 T H 15 T 16 T 17 18 M700 7 TC 19 AREA OF CONSTRUCTION True NorthPlan NorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates KEY PLAN IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:07:45 PMFirst Floor Mechanical Plans M210 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation For 1/4" = 1'-0"1 First Floor Mechanical Ductwork Plan 1/4" = 1'-0"2 First Floor Mechanical Demolition Plan PLAN NOTES 1 REMOVE EXISTING SUPPLY DUCT BACK TO POINT INDICATED. 2 REMOVE EXISTING LAMINAR FLOW DIFFUSER COMPLETE. 3 REMOVE EXISTING TERMINAL UNIT, ASSOCIATED DUCTWORK, PIPING, AND CONTROLS COMPLETE. 4 REMOVE EXISTING THERMOSTAT COMPLETE. 5 REMOVE EXISTING RETURN GRILLE AND PORTION OF DUCT CONNECTION AS REQUIRED TO INSTALL NEW WALL RETURN GRILLE. 6 REMOVE EXISTING RETURN DUCT BACK TO MAIN AND CAP SUITABLE FOR -4" W.G. 7 REMOVE EXISTING RETURN DUCT STUBBED INTO CASEWORK COMPLETE AND PATCH DUCT SUITABLE FOR -4" W.G. 8 DIRECT RETURN AIR GRILLE LOUVERS TO DRAW AIR FROM DIRECTLY ABOVE CATH LAB EQUIPMENT. 9 DIRECT SUPPLY AIR DISCHARGE GRILLES TOWARDS WEST WALL OF EQUIPMENT ROOM. THE INTENT OF THE GRILLE IS TO PUSH THE SUPPLY AIR DOWN TO THE FLOOR LEVEL TO BE DRAWN IN BY THE CATH LAB EQUIPMENT. 10 CONFIRM EXACT LOCATION OF EXISTING DUCTWORK ABOVE CEILING AND COORDINATE WITH NEW CATH EQUIPMENT SUPPORT STRUCTURE. RELOCATE DUCTWORK AS REQUIRED TO FACILITATE SUPPORT STEEL. 11 INSTALL TERMINAL UNIT IN AN UNOBSTRUCTED LOCATION. 12 INSTALL NEW FILTERED RETURN GRILLE AT APPROXIMATELY 8" ABOVE FINISHED FLOOR. RECONNECT TO EXISTING RETURN DUCT RISER AND PATCH WALL. 13 NEW ROOM DIFFERENTIAL PRESSURE MONITOR, SIMILAR TO CRC-PM WITH BACNET CONTROLS. 14 NEW ROOM ENVIRONMENTAL INTERFACE CONTROLLER, SIMILAR TO CRC-MRM. REFER TO TEMPERATURE CONTROL SCHEMATICS ON M600 FOR ADDITIONAL INFORMATION. 15 REMOTE TEMPERATURE AND HUMIDITY SENSORS. 16 DUCT MOUNTED RETURN AIR TEMPERATURE SENSOR FOR CONTROL OF CATH EQUIPMENT ROOM. 17 EXISTING THERMOSTAT TO REMAIN. 18 CONNECT NEW HWS&R TO EXISTING HWS&R. 19 120V/24V, 500 VA TEMPERATURE CONTROL TRANSFORMER. TRANSFORMER PROVIDED AND INSTALLED BY TEMPERATURE CONTROL CONTRACTOR. TEMPERATURE CONTROL CONTRACTOR SHALL LOCATE THE TRANSFORMER AND COORDINATE WITH ELECTRICAL CONTRACTOR. 1/4" = 1'-0"3 First Floor Mechanical Piping Plan REV. DATE SEQUENCE OF OPERATION (ALL SETPOINTS, TIMERS, AND SCHEDULES SHALL BE ADJUSTABLE) 1.CATH LAB IS MANUALLY INDEXED FROM "OCCUPIED" TO "UNOCCUPIED" UTILIZING THE CATH LAB ROOM TEMPERATURE CONTROLLER/MONITOR. OCCUPANCY SENSORS SHALL AUTOMOATICALLY RESTORE OCCUPIED STATUS TO ROOM. 2. OCCUPIED MODE: 2.1 SUPPLY AIRFLOW SHALL BE HELD AT A CONSTANT VOLUME TO MAINTAIN A MINIMUM OF 20 AIR CHANGES DURING OCCUPIED MODE. 2.2 RETURN SIRFLOW CONTROL VALVE SHALL TRACK SUPPLY AIR VOLUME MINUS AN OFFSET OF APPROXIMATELY 500 CFM TO MAINTAIN A MINIMUM POSITIVE PRESSURE OF +0.01". OFFSET SHALL BE VERIFIED AND ADJUSTED DURING STARTUP/TAB. 2.3 SPACE TEMPERATURE SHALL BE MAINTAINED AT +/-1°F FROM A SETPOINT OF 68°F BY MODULATING THE REHEAT COIL CONTROL VALVE. 2.4 ANYTIME THE CATH LAB ROOM PRESSURE FALLS BELOW +0.01" W.G. A VISUAL NOTIFICATION SHALL BE OBSERVABLE AT THE PRESSURE CONTROLLER MOUNTED IN THE CORRIDOR. IF THE ROOM PRESSURE REMMAINS BELOW +0.01" FOR A PERIOD OF FIVE MINUTES, AN ALARM SHALL BE GENERATED THROUGH THE BMS. 3.UNOCCUPIED MODE: 3.1 SUPPLY AIR SHALL BE REDUCED TO THE UNOCCUPIED AIRFLOW SCHEDULED. 3.2 RETURN AIRFLOW CONTROL VALVE SHALL TRACK SUPPLY AIR AND MAINTAIN THE SAME OFFSET SETPOINT USED FOR OCCUPIED MODE. 3.3 SURGERY PRESSURE ALARMS SHALL BE NEGATED TO PREVENT NUISANCE ALARMS GENERATED DURING CLEANING PROCEDURES. 3.4 CONTROL SYSTEM SHALL HAVE A PROGRAMMED OCCUPIED/UNOCCUPIED SCHEDULE AS DETERMINED BY THE OWNER. ROOM TEMPERATURE CONTROL SCREEN SHALL HAVE A LOCAL OVERRIDE SWITCH TO INITIATE "OCCUPIED" MODE. HWR HWS AMS TU-B168 MDT AI-2 AO-3 AI-3 AO-2 CATH B168 ∆P BI-3 ∆P 24V FROM BAS BACNET LAN TO BAS AI-1 AMS AFCV-B168 MD AO-1 AI-4 T AI-5 H AI-6 AO-4 24V FROM BAS BACNET LAN TO BAS (-) (+) 3 1 2 OS BI-2 4 BI-4 BI-1 LFD1 8"Ø 24"X24"0 - 150 20 0.50 PRICE LFDC 1, 2, 3, 4 PRICELFD210"Ø 24"X48"155 - 250 20 0.40 LFDC 16 19 DIFFUSER/REGISTER/GRILLE SCHEDULE TAG NECK SIZE FACE SIZE (IN.)MATERIAL CFM RANGE MAX. NC MAX. TOTAL A.P.D. (IN. WG.) MANUFACTURER MODEL NOTES DESIGN REFERENCETHROW (FT. BASED ON VELOCITY OF 50 FPM) SD1/RD1/ED1 8"Ø 24"X24""0 - 180 20 0.040 PRICE12 SD2/RD2/ED2 10"Ø 24"X24""185 - 300 25 0.040 PRICE13 SD0/RD0/ED0 6"Ø 12"X12""0 - 100 15 0.040 PRICE APDSP10 SD3/RD3/ED3 12"Ø 24"X24""305 - 400 25 0.040 PRICE14 ALUMINUM APDSP APDSP APDSP AIR TERMINAL TYPE PERFORATED CEILING DIFFUSER LAMINAR FLOW HEPA LAMINAR FLOW HEPA 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3, 4 ALUMINUM ALUMINUM ALUMINUM ALUMINUM ALUMINUM PERFORATED CEILING DIFFUSER PERFORATED CEILING DIFFUSER PERFORATED CEILING DIFFUSER SG1 18"X14"18"X14"0 - 650 20 0.01 PRICE 22 1, 2, 3, 5 PRICERG10 - 650 20 0.01 22 37 N/A CEILING SUPPLY GRILLE LAMINAR FLOW HEPA 1, 2, 3, 5 ALUMINUM ALUMINUM18"X14"18"X14" NOTES: 1. BRANCH DUCT RUNOUT TO THE DIFFUSER SHALL BE THE SAME SIZE AS THE DIFFUSER NECK UNLESS NOTED OTHERWISE ON THE DRAWINGS. 2. ALL SUPPLY DIFFUSER BACKPLATES SHALL BE INSULATED WITH A MINIMUM OF 1" INSULATION. INSULATION MAY BE FACTORY OR FIELD APPLIED. 3. PROVIDE FRAME STYPLE APPROPRIATE FOR CEILING TYPE (I.E. LAY-IN, SURFACE MOUNT, SIDEWALL, ETC.). REFER TO DRAWINGS AND ARCHITECTURAL REFLECTED CEILING PLANS FOR LOCATIONS. 4. DIFFUSER SHALL HAVE INTEGRAL HEPA FILTER THAT CAN BE ACCESSED BY REMOVAL OF THE HINGED ALUMINUM FACEPLATE. PROVIDE PORTS FOR READING DIFFUSER PRESSURE DROP. 5. BLADES PARALLEL TO THE LONG DIMENSION. 6. BLADES PARALLEL TO THE SHORT DIMENSION. 7. PROVIDE MERV 7 FILTER INTEGRAL TO GRILLE. FILTER SHALL BE REMOVABLE BY HINGED FACE. PRICEWRG10 - 700 20 0.03 735FFN/AWALL FILTER RETURN GRILLE 1, 2, 3, 6, 7ALUMINUM16"X24"16"X24" SEQUENCE OF OPERATION: (ALL SETPOINTS, TIMERS, AND SCHEDULES SHALL BE ADJUSTABLE) 1.TERMINAL UNIT CONTROLLER SHALL RESPOND TO CHANGES IN SPACE TEMPERATURE AND VARIATIONS IN SYSTEM STATIC PRESSURE TO MODULATE SUPPLY AIR VOLUME FROM SCHEDULED MINIMUM TO MAXIMUM THERE SHALL BE SEPARATE ADJUSTABLE SETPOINTS FOR COOLING MINIMUM AIRFLOW, MINIMUM AIRFLOW, AND SPACE TEMPERATURE SETPOINT. PRIMARY SUPPLY FROM RTU CONTROL PANEL LAN TO NETWORK CONTROLLER AMSMD 24V T DISCONNECT BY VAV MANUFACTURER SPACE TEMPERATURE SENSOR WITH +/-4°F FROM SETPOINT ADJUSTMENT VAV AIR TERMINAL UNIT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:07:53 PMMechanical Schedules and Temp. Control Schematics M600 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation ForTERMINAL UNIT SCHEDULE TAG UNIT INLET SIZE ("Ø) DUCT RUNOUT SIZE ("Ø) AIRFLOW DATA HOT WATER REHEAT COIL DATA NOTESAIRFLOW MAXIMUM (CFM) AIRFLOW MINIMUM (CFM) AIRFLOW MAXIMUM HEATING (CFM) MAXIMUM AIR PRESSURE DROP (IN. W.C.) ENTERING AIR TEMPERATURE (°F) LEAVING AIR TEMPERATURE (°F) HEAT OUTPUT AT HEATING AIRFLOW (MBH) WATER FLOW RATE (GPM) PIPE RUNOUT SIZE (IN) ETU-B167 8 8 350 150 150 0.3 50 95 7.3 0.6 5 TU-B167A 10 10 650 0 N/A 0.1 50 50 N/A N/A N/A 3, 4, 6, 7 TU-B168 14 14 1,875 850 1,875 0.5 50 85 71.2 4.7 2, 3, 4, 7 AIRFLOW CONTROL VALVE SCHEDULE TAG UNIT INLET SIZE ("Ø) DUCT RUNOUT SIZE ("Ø) AIRFLOW DATA NOTESAIRFLOW MAXIMUM (CFM) AIRFLOW MINIMUM (CFM) MAXIMUM AIR PRESSURE DROP (IN. W.C.) AFCV-B168 12 14 1,375 350 0.1 1, 2 NOT TO SCALE1CATH LAB TEMPERATURE CONTROL SCHEMATIC POINT LIST AI-1 CATH LAB SPACE DIFFERENTIAL PRESSURE AI-2 TU-B168 DISCHARGE AIR TEMPERATURE AI-3 TU-B168 AIRFLOW READING (CFM) AI-4 AFCV-B168 AIRFLOW READING (CFM) AI-5 SPACE TEMPERATURE AI-6 SPACE HUMIDITY AO-1 AFCV-B168 MOTORIZED DAMPER AO-2 TU-B168 REHEAT COIL VALVE AO-3 TU-B168 MOTORIZED DAMPER AO-4 CATH LAB ROOM TEMPERATURE SETPOINT ADJUSTMENT BI-1 OCCUPANCY SENSOR BI-2 OCCUPANCY SENSOR BI-3 HEPA FILTER DIFFUSER PRESSURE DROP ALARM - 2' X 4' DIFFUSER BI-4 HEPA FILTER DIFFUSER PRESSURE DROP ALARM - 2' X 2' DIFFUSER PLAN NOTES 1 CATH LAB ROOM PRESSURE MONITOR. CONTROLLER SHALL DISPLAY ROOM PRESSURE AND OCCUPIED/UNOCCUPIED STATUS. CONTROLLER SHALL BE PROGRAMMED TO DISPLAY A VISUAL STATUS OF ALARM WHEN ROOM PRESSURE FALLS BELOW SETPOINT. SIMILAR TO CRITICAL ROOM CONTROL CRC-PM WITH BACNET COMMUNICATION. 2 CATH LAB ROOM MONITOR AND SETPOINT CONTROLLER. CONTROLLER SHALL BE A TOUCHSCREEN COLOR DISPLAY OF SPACE TEMPERATURE, SPACE TEMPERATURE SETPOINT, HUMIDITY, AND ROOM PRESSURE. DISPLAY SHALL ALLOW FOR ADJUSTEMENT OF ROOM TEMPERATURE AND OCCUPIED/UNOCCUPIED OVERRIDE MODE. SIMILAR TO CRITICAL ROOM CONTROL CRC-MPM WITH BACNET COMMUNICATION. 3 ROOM SHALL HAVE LAMINAR FLOW DIFFUSERS WITH HEPA FILTERS. INSTALL A DIFFERENTIAL PRESSURE SWITCH ON ONE OF THE 2'X2' DIFFUSERS AND ONE OF THE 2'X4' DIFFUSERS. SET SWTCH TO NOTIFY BMS WHEN THE DIFFERENTIAL PRESSURE REACHES TWICE THE INITIAL PRESSURE DROP. 4 CEILING MOUNTED OCCUPANCY SENSORS (2). INSTALL ONE SENSOR NEAR THE HEAD OF THE TABLE AND THE OTHER NEAR THE FOOT OF THE TABLE TO ENSURE COMPLETE COVERAGE. NOT TO SCALE2COOLING ONLY TERMINAL UNIT CONTROL SCHEMATIC 1 1 NOTES: 1.EXISTING PIPE RUNOUT IS 3/4" TO REMAIN. 2.COIL SHALL BE A MINIMUM OF 2-ROWS. HEATING COIL PERFORMANCE IS BASED ON 180°F ENTERING WATER TEMPERATURE, 150F LEAVING WATER TEMPERATURE, 50°F ENTERING AIR TEMPERATURE, AND 85°F LEAVING AIR TEMPERATURE. SUBMIT THIS PERFORMANCE FOR REVIEW AS WELL AS A CONDITION WITH 120°F ENTERING WATER TEMPERATURE AND 75°F LEAVING AIR TEMPERATURE. ADJUST TERMINAL UNIT SIZE OR COIL ROWS AS REQUIRED TO MEET BOTH CONDITIONS. 3.TERMINAL UNIT SHALL HAVE 1" INSULATION AND DOUBLE WALL SHEETMETAL CASING. 4.PROVIDE ACCESS DOOR AND HANGER TABS. 5.EXISTING TERMINAL UNIT TO BE REUSED. BALANCE TO AIRFLOW AND WATERFLOW INDICATED. 6.COOLING ONLY TERMINAL UNIT. 7.SIMILAR TO PRICE SDV NOTES: 1.PROVIDE HANGER TABS. 2.SIMILAR TO PRICE SDV REV. DATE FLEXIBLE DUCTWORK BENDS SHALL NOT BE LESS THAN 1.5 TIMES THE DUCT DIAMETER. INSULATION AND VAPOR BARRIERS PRESENT ON FACTORY-FABRICATED DUCTS SHALL BE FITTED OVER THE CORE CONNECTION AND SHALL BE SECURED WITH A DRAW BAND. TAPE AND SEAL ALL JOINTS AND SEAMS WITH FSK TAPE TO MAINTAIN VAPOR BARRIER. SUPPORT FLEXIBLE DUCTWORK FROM STRUCTURE. DO NOT SUPPORT FLEXIBLE DUCTWORK FROM ADJACENT ABOVE CEILING UTILITIES (DUCTWORK, PIPING, CONDUITS, ETC.) A. B. C. GENERAL DETAIL NOTES: FLEX DUCT-MAXIMUM 8'-0" LENGTH AND NO MORE THAN TWO (2) 90° BENDS. INSULATE BACK OF SUPPLY DIFFUSERS WITH 1" MINERAL FIBER INSULATION WITH FSK JACKET. TAPE AND SEAL INSULATION VAPOR BARRIER. CEILING SUPPLY DIFFUSER ATTACH FLEXIBLE DUCTWORK WITH DRAWBAND AND SEAL INSULATION AND VAPOR BARRIER TO FSK TAPE. INSTALL MANUAL VOLUME DAMPER AT ALL BRANCH DUCTS. PROVIDE 2" EXTENDED OPERATOR HANDLE FOR INSULATED DUCTS. SPIN-IN FITTING AT BRANCH/MAIN CONNECTION. DUCT (TYP) FILL SPACE AROUND DUCT WITH NONCOMBUSTIBLE SEALANT. FINISHED WALL SURFACE OF RATED ASSEMBLY FINISHED WALL SURFACE UNINSULATED DUCT THROUGH INTERIOR FIRE RATED BARRIERS UNINSULATED DUCT THROUGH INTERIOR NON-RATED WALLS OR SMOKE-RESISTANT CORRIDOR WALLS FRAMED WALL OPENING (TYP) INSULATION CONTINUOUS THROUGH WALL (TYP) FINISHED WALL SURFACE OF RATED ASSEMBLY FILL ANNULAR GAPS EACH SIDE OF DUCT ON EACH SIDE OF WALL WITH NONCOMBUSTIBLE SEALANT. FINISHED WALL SURFACE INSULATED DUCT THROUGH INTERIOR NON-RATED OR SMOKE-RESISTANT CORRIDOR WALLS INSULATED DUCT THROUGH INTERIOR FIRE RATED BARRIERS DETAIL NOTES: INSTALL FIRESTOP AND RETAINING ANGLES AS SPECIFIED IN DIVISION 7. ALL PENETRATIONS SHALL MEET UL LISTED RATING APPROPRIATE FOR WALL RATING. WHERE A DUCT PENETRATIONS A 1-HR FIRE RATED BARRIER, EXTEND SHEETMETAL DUCT AT LEAST 4 X DIA ON BOTH SIDES OF PENETRATION PRIOR TO TRANSITIONING TO FLEXIBLE DUCT. WHERE THIS IS NOT POSSIBLE, INSTALL A FIRE DAMPER AND ACCESS PANEL AT WALL PENETRATION. INSTALL FIRESTOP LABEL ABOVE CEILING ON BOTH SIDES OF PENETRATION 1 2 2 1 1 2 REFER TO PLANS FOR SIZE RETURN/ EXHAUST DUCT CEILING FLOOR 8" AFF1 2 DETAIL NOTES GRILLE SHALL BE 8" FROM BOTTOM OF GRILLE TO FINISHED FLOOR LEVE.1 LOCATE BALANCE DAMPER IN AN ACCESSIBLE LOCATION ABOVE LAY-IN CEILING. WHERE DAMPER CANNOT BE LOCATED ABOVE LAY-IN CEILING, INSTALL AN ACCESS PANEL. 2 INSTALL 8' OF FLEXIBLE DUCTWORK SPIN-IN DUCT CONNECTION DETAIL NOTES UTILIZE HIGH VELOCITY TAKE-OFFS FOR MAIN/BRANCH CONNECTION: SQUARE TO SQUARE - BEVELED BOOT-TAP SQUARE TO ROUND - BELLMOUTH ROUND TO ROUND - LATERAL WHERE DUCT RUNOUT IS LONGER THAN 10', INCREASE THE RUNOUT SIZE TO THE NEXT LARGER EVEN SIZE UNLESS NOTED OTHERWISE. PROVIDE A MINIMUM OF 3 X INLET DIAMETERS OF STRAIGHT DUCT RUN AT TERMINAL UNIT INLET. A MAXIMUM OF 1'-0" FLEXIBLE DUCT MAY BE USED AT TERMINAL UNIT CONNECTION BUT MUST BE PULLED TIGHT AND NOT USED FOR CHANGES IN DIRECTION. ALLOW A MINIMUM OF 24"X36" CLEARANCE ADJACENT TO THE TERMINAL UNIT CONTROL PANEL. INCREASE ACCESS AS REQUIRED FOR NEC MINIMUM CLEARANCE. ROUTE ALL PIPING OUTSIDE OF THIS SERVICE AREA. INSTALL SUCH THAT VALVES AND OTHER PIPING ACCESSORIES ARE ACCESSIBLE FROM THIS LOCATION. SERVICE AREA SHALL EXTEND DOWN TO AND INCLUDE THE CEILING BELOW. COORDINATE WITH ALL TRADES SUCH THAT SERVICE AREA IS UNOBSTRUCTED BY LIGHTS, DIFFUSERS, SPRINKLER HEADS, SPEAKERS, OR OTHER CEILING INSTALLED DEVICES. DISCHARGE DUCT SHALL BE THE SAME SIZE AS THE TERMINAL UNIT DISCHARGE CONNECTION UNLESS NOTED OTHERWISE. TRANSITION TO A DEEPER DUCT AS REQUIRED FOR DIFFUSER RUNOUT SIZES. SUPPORT TERMINAL UNIT WITH HANGER RODS OR STRAPS AT ALL FOUR CORNERS. TERMINAL UNIT SUPPORTS SHALL EXTEND UP TO STRUCTURE. DO NOT SUPPORT FROM DUCTWORK, PIPES, OR OTHER SERVICES LOCATED ABOVE CEILING. INSULATE ALL EXPOSED METAL THAT IS NOT FACTORY INSULATED. EXTEND DUCT INSULATION 2" PAST BOUNDARY OF INSULATED/UNINSULATED MATERIALS AND SEAL WITH FSK TAPE. DO NOT OBSTRUCT FACTORY INSTALLED ACCESS DOOR. INSTALL DIFFUSER RUNOUT IN THE SIDE OF THE DISCHARGE DUCT WITH SPIN-IN DUCT FITTINGS AND MANUAL VOLUME DAMPERS. VOLUME DAMPER OPERATORS SHALL EXTEND 2" BEYOND DUCT TO ALLOW FOR INSULATION TO BE INSTALLED. TERMINAL UNIT DISCHARGE DUCT SHALL HAVE A "DEAD-END" WHERE NOT DIFFUSERS ARE CONNECTED TO ALLOW FOR END REFLECTION SOUND CONTROL. 1 1 2 2 3 3 4 4 REFER TO DIFFUSER DETAIL FOR REQUIREMENTS 5 5 6 6 SUPPLY MAINDETAIL NOTES UTILIZE HIGH VELOCITY TAKE-OFFS FOR MAIN/BRANCH CONNECTION: SQUARE TO SQUARE - BEVELED BOOT-TAP SQUARE TO ROUND - BELLMOUTH ROUND TO ROUND - LATERAL REFER TO PLANS FOR DUCT SIZE. ALLOW A MINIMUM OF 24"X36" CLEARANCE ADJACENT TO THE AIRFLOW CONTROL VALVE CONTROL PANEL. INCREASE ACCESS AS REQUIRED FOR NEC MINIMUM CLEARANCE. SERVICE AREA SHALL EXTEND DOWN TO AND INCLUDE THE CEILING BELOW. COORDINATE WITH ALL TRADES SUCH THAT SERVICE AREA IS UNOBSTRUCTED BY LIGHTS, DIFFUSERS, SPRINKLER HEADS, SPEAKERS, OR OTHER CEILING INSTALLED DEVICES. SUPPORT AIRFLOW CONTROL VALVE WITH HANGER RODS OR STRAPS AT ALL FOUR CORNERS. UNIT SUPPORTS SHALL EXTEND UP TO STRUCTURE. DO NOT SUPPORT FROM DUCTWORK, PIPES, OR OTHER SERVICES LOCATED ABOVE CEILING. INSTALL GRILLE RUNOUT IN THE SIDE OF THE DISCHARGE DUCT WITH SPIN-IN DUCT FITTINGS AND MANUAL VOLUME DAMPERS. 1 1 2 2 3 3 4 REFER TO DIFFUSER DETAIL FOR REQUIREMENTS 4 5 5 RETURN/EXHAUST MAIN2 EXTERIOR WALLS PROVIDE ESCUTCHEON PLATE FLUSH AGAINST WALL AND OF SIZE TO COMPLETELY COVER OPENING IN EXPOSED AREAS ONLY. NOTES: SEE SPECIFICATION SECTIONS FOR FURTHER REQUIREMENTS INCLUDING FLOOR SLEEVES. INSULATED OR UNINSULATED PIPE THROUGH INTERIOR NON-RATED WALLS OR SMOKE=RESISTANT CORRIDOR WALLS UNINSULATED PIPE THROUGH INTERIOR FIRE RATED WALLS INSULATED PIPE THROUGH INTERIOR FIRE RATED WALLS LOCATE FIRESTOP LABEL ON EACH SIDE OF PENETRATION SO THAT IT IS VISIBLE FROM AN ACCESSIBLE LOCATION ABOVE CEILING. INCLUDES FIRE WALLS, FIRE BARRIERS, SMOKE BARRIERS, AND FIRE PARTITIONS. TERMINATE SLEEVE FLUSH WITH FINISHED WALL PIPE (TYP) FIRESTOP EACH SIDE OF SLEEVE AS SPECIFED IN DIV 7 FINISHED WALL SURFACE OF RATED ASSEMBLY WALL HYDO-STATIC MECHANICAL SLEEVE SEAL, SIMILAR TO LINK- SEAL. PIPE PIPE SLEEVE TO BE SIZED TO PASS PIPE THRU SLEEVE AND ALLOW SPACE FOR SEALANT TO MEET UL-LISTING TERMINATE SLEEVE FLUSH WITH FINISHED WALL FINISHED WALL SURFACE OF RATED ASSEMBLY PIPE SLEEVE TO BE SIZED TO PASS PIPE AND INSULATION THRU SLEEVE AND ALLOW SPACE FOR SEALANT TO MEET UL-LISTING INSULATION CONTINUOUS THROUGH WALL (TYP) FILL ANNULAR GAPS AROUND PIPES ON EACH SIDE OF WALL WITH NONCOMBUSTIBLE SEALANT. NONCOMBUSTIBLE SEALANT FINISHED WALL SURFACE SLEEVE WATER STOP WALL SLEEVE 3 1 2 3 4 1 1 4 3 5 INSTALL FIRESTOP AND RETAINING ANGLES AS SPECIFIED IN DIVISION 7. ALL PENETRATIONS SHALL MEET UL LISTED RATING APPROPRIATE FOR WALL RATING. 5 COIL P/T PLUG (TYP.)BALL VALVE (TYP.) STRAINER W/ BLOWDOWN VALVE AND CAP UNION (TYP.) CALIBRATED BALANCE VALVE 2-WAY MODULATING CONTROL VALVE MANUAL AIR VENT. INSTALL AT HIGHEST POINT IN RETURN PIPING DETAIL NOTES: INSTALL BUTTERFLY VALVES IN LIEU OF BALL VALVES WHEN PIPE SIZE IS 2-1/2" AND GREATER. INSTALL THERMOMETER WHEN CONNECTING TO AIR HANDLING UNIT COILS. PROVIDE SEPARATE DEDICATED SHUT-OFF VALVE. BALANCE VALVE IS NOT TO BE USED FOR SHUT-OFF DUTY. 1 1 3/4" DRAIN WITH BALL VALVE, HOSE CONNECTION AND CAP. INSTALL AT LOWEST POINT IN PIPING 2 2 2 3 3 Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:07:59 PMMechanical Details M700 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation ForNO SCALE1CEILING DIFFUSER/GRILLE DETAIL NO SCALE2DUCT PENETRATION DETAIL NO SCALE3LOW EXHAUST/RETURN DETAIL NO SCALE4TERMINAL UNIT DETAIL NO SCALE5AIRFLOW CONTROL VALVE DETAIL NO SCALE6PIPE PENETRATION DETAILS NO SCALE7COIL 2-WAY WATER COIL PIPING DETAIL REV. DATE A or AMP AC A/C ACP ACU ADD ADJ AF AFC AFF AFG AHU AIC AL AM AMB APPROX. ARCH ATS AUTO AVG BC BKR BHP BL BLDG BR BTM C ºC CAB CB or C/B C/C CCTV CKT CL CLG COL COMM COMP CONC CONST CONT CONTR CR CT CU DB DC DEPT DF DIST DM DO DRS DWG EC EF ELEC ELEV ELV EMER ENCL EP EQUIP EWC EX EXH EXP EXT ºF FA FAAP FACP FC FCU FFC FFS FHC FIN FIXT FL FLUOR FLEX-CONN FPC FSS FTG FVR FV FVNR G or GND GALV GC GEN GFCI GFI GFP HGT HH HID HO HOA HORZ HP HPS HTR HV AMPERE ALTERNATING CURRENT AIR CONDITIONING ACCESS PANEL AIR CONDITIONING UNIT ADDITION ADJUSTABLE AMPERE FRAME ABOVE FINISHED CEILING ABOVE FINISHED FLOOR ABOVE FINISHED GRADE AIR HANDLING UNIT AMPERE INTERRUPTING CAPACITY ALUMINUM AMMETER AMBIENT APPROXIMATELY ARCHITECT AUTOMATIC TRANSFER SWITCH AUTOMATIC AVERGE BARE COPPER BREAKER BRAKE HORSEPOWER BUILDING LINE BUILDING BRANCH BOTTOM CONDUIT DEGREES CELSIUS CABINET CIRCUIT BREAKER CENTER TO CENTER CLOSED CIRCUIT TELEVISION CIRCUIT CENTER LINE CEILING COLUMN COMMUNICATION COMPRESSOR CONCRETE CONSTRUCTION CONTINUOUS CONTRACTOR CRITICAL CURRENT TRANSFORMER COPPER DIRECT BURIAL DIRECT CURRENT DEPARTMENT DRINKING FOUNTAIN DISTRIBUTION DEMAND METER DRAWOUT DOCTORS DRAWING ELECTRICAL CONTRACTOR EXHAUST FAN ELECTRIC ELEVATOR ELEVATION EMERGENCY ENCLOSURE ELECTRIC PNEUMATIC EQUIPMENT ELECTRIC WATER COOLER EXPLOSIONPROOF EXHAUST EXPANSION EXTERIOR DEGREES FAHRENHEIT FIRE ALARM FIRE ALARM ANNUNCIATOR PANEL FIRE ALARM CONTROL PANEL FLAT CABLE FAN COIL UNIT FOOD FACILITY CONTRACTOR FOOD FACILITY SUPPLIER FIRE HOSE CABINET FINISH FIXTURE FLOOR FLUORESCENT FLEXIBLE CONNECTION FIRE PROTECTION CONTRACTOR FUSED SAFETY SWITCH FOOTING FILMVIEWER FULL VOLTAGE FULL VOLTAGE NON REVERSING GROUND GALVANIZED GENERAL CONTRACTOR GENERATOR GROUND FAULT CKT. INTERRUPTER GROUND FAULT INTERRUPTER GROUND FAULT PROTECTION HEIGHT HANDHOLE HIGH INTENSITY DISCHARGE HAND OPERATED HAND-OFF-AUTOMATIC HORIZONTAL HORSEPOWER HIGH PRESSURE SODIUM HEATER HIGH VOLTAGE HZ IC ID INCAN INCL ISG JB JT KEC KT KVA KVAR KW LAB LB LF LOC LS LT LTG LV MATV MAX MC MCB MCC MDP MECH MH MIN MISC MLO MTD MTG HT MU OD OFCI OFOI OPNG OPP OR P PB PBOX PE PF PH or Ø PV PNL PL PREFAB PRES PT PTS PW PWR RACU RAD RECEPT REF or REFR REINF RGIP RM RPM SA SC SG SHT SIG SN SPEC SQ SS SSSS STD STN STR SUSP SW SWBD SWGR TCC TELE TEMP TMH TV TYP UC U/C UH UV V VAC VB VC VEL VFD VM VOL VP VSD/VFC W/ W/O WTR WP WT XFMR Z HERTZ INTERCOMMUNICATION INSIDE DIAMETER INCANDESCENT INCLUDE ISOLATED GROUND SURGE GUARD JUNCTION BOX JOINT KITCHEN EQUIPMENT CONTRACTOR KITCHENETTE KILOVOLT AMPERE KILOVOLT AMPERE REACTIVE KILOWATT LABORATORY POUND LINEAR FEET LOCATION LIFE SAFETY LIGHT LIGHTING LOW VOLTAGE MASTER ANTENNA TELEVISION MAXIMUM MECHANICAL CONTRACTOR MAIN CIRCUIT BREAKER MOTOR CONTROL CENTER MAIN DISTRIBUTION PANEL MECHANICAL MANHOLE MINIMUM MISCELLANEOUS MAIN LUGS ONLY MOUNTED MOUNTING HEIGHT MEDICINE UNIT OUTSIDE DIAMETER OWNER FURNISHED-CONTRACTOR INSTALLED OWNER FURNISHED-OWNER INSTALLED OPENING OPPOSITE OPERATING ROOM POLE PUSHBUTTON PULL BOX PNEUMATIC ELECTRIC CONVERTER POWER FACTOR PHASE POST INDICATOR VALVE PANELBOARD PILOT LIGHT PREFABRICATED PRESSURE PNEUMATIC TUBE PNEUMATIC TUBE STATION PART WINDING POWER ROOM AIR CONDITIONING UNIT RADIATION RECEPTACLE REFRIGERATOR REINFORCED REMOTE GROUND INDICATING PANEL ROOM REVOLUTIONS PER MINUTE SUPPLY AIR SHORT CIRCUIT SURGE GUARD PROTECTION SHEET SIGNAL SOLID NEUTRAL SPECIFICATIONS SQUARE SAFETY SWITCH SOLID STATE SOFT START STANDARD STATION STRUCTURAL SUSPENDED SWITCH SWITCHBOARD SWITCHGEAR TEMPERATURE CONTROL CONTRACTOR TELECOMMUNICATION TEMPERATURE TOP OF MANHOLE TELEVISION TYPICAL UNDER CARPET UNDER CABINET or UNDER COUNTER UNIT HEATER UNIT VENTILATOR VOLT VACUUM VACUUM BREAKER VACUUM CLEANING VELOCITY VARIABLE FREQUENCY DRIVE VOLTMETER VOLUME VAPORPROOF VARIABLE SPEED DRIVE/CONTROLLER WITH WITHOUT WATER WEATHERPROOF WEIGHT TRANSFORMER IMPEDANCE ELECTRICAL ABBREVIATIONS M FIRE ALARM SYSTEM SYMBOL DESCRIPTION MANUAL SENDING STATION PIV POST INDICATOR VALVE SD CEILING SMOKE DETECTOR TS SPRINKLER SYSTEM TAMPER SWITCH FS SPRINKLER SYSTEM FLOW SWITCH SD WALL SMOKE DETECTOR SD WALL SMOKE DETECTOR WITH SOUNDER BASE SD CEILING SMOKE DETECTOR WITH SOUNDER BASE DD AUTOMATIC DUCT DETECTOR ("X" DENOTES AS FOLLOWS) RT REMOTE DETECTOR TEST STATION RI REMOTE DETECTOR INDICATOR STATION AR FIRE ALARM ADDRESSABLE RELAY X NONE - PHOTOELECTRIC TYPE S - SUPPLY R - RETURN DR DOOR RELEASE DU DOOR UNLOCK J FIREMANS JACK HD HEAT DETECTOR FD FLAME DETECTOR BD BEAM DETECTOR H WALL HORN ONLY H WALL HORN STROBE CEILING HORN ONLY CEILING HORN STROBE H H S WALL SPEAKER ONLY S WALL SPEAKER STROBE CEILING SPEAKER STROBES V WALL VISUAL ONLY CEILING VISUAL ONLYV FACP FIRE ALARM CONTROL PANEL FAAP FIRE ALARM ANNUNCIATOR PANEL ALL SYMBOLS AND ABBREVIATIONS MAY NOT BE USED ON THIS PROJECT3 ST - 20 AMP, 125VAC, SAFETY TYPE S - 20 AMP, 125VAC, SURGE GUARD PROTECTION TYPE WP - 20 AMP, 125VAC, WEATHERPROOF TYPE HM - 20 AMP, 125VAC, HORIZONTAL MOUNT TYPE IG - 20 AMP, 125VAC, ISOLATED GROUND TYPE NONE - 20 AMP, 125VAC ELECTRICAL RECEPTACLES DUPLEX RECEPTACLE - NORMAL POWER CIRCUIT DESCRIPTIONSYMBOL DUPLEX RECEPTACLE - EMERGENCY POWER CIRCUIT DUPLEX GFCI RECEPTACLE - NORMAL POWER CIRCUIT DUPLEX GFCI RECEPTACLE - EMERGENCY POWER CIRCUIT QUADRAPLEX RECEPTACLE - NORMAL POWER CIRCUIT QUADRAPLEX RECEPTACLE - EMERGENCY POWER CIRCUIT QUADRAPLEX GFCI RECEPTACLE - NORMAL POWER CIRCUIT QUADRAPLEX GFCI RECEPTACLE - EMERGENCY POWER CIRCUIT SIMPLEX RECEPTACLE - NORMAL POWER CIRCUIT SIMPLEX RECEPTACLE - EMERGENCY POWER CIRCUIT SPECIAL RECEPTACLE - NORMAL POWER CIRCUIT SPECIAL RECEPTACLE - EMERGENCY POWER CIRCUIT DUPLEX RECEPTACLE - TOP SWITCHED "X" DENOTES AS FOLLOWS: CEILING DUPLEX RECEPTACLE - NORMAL POWER CIRCUIT CEILING DUPLEX RECEPTACLE - EMERGENCY POWER CIRCUIT CEILING QUADRAPLEX RECEPTACLE - NORMAL POWER CIRCUIT CEILING QUADRAPLEX RECEPTACLE - EMERGENCY POWER CIRCUIT FLOOR BOX DUPLEX RECEPTACLE - NORMAL POWER CIRCUIT FLOOR BOX DUPLEX RECEPTACLE - EMERGENCY POWER CIRCUIT FLOOR BOX QUADRAPLEX RECEPTACLE - NORMAL POWER CIRCUIT FLOOR BOX QUADRAPLEX RECEPTACLE - EMERGENCY POWER CIRCUIT FLOOR BOX POWER AND TELECOM FLOOR BOX BLANK MULTI-OUTLET ASSEMBLY (POWER AND/OR TELECOM) ELECTRICAL SWITCHES DESCRIPTIONSYMBOL TOGGLE SWITCH - 20 AMP, 120/277VAC TOGGLE SWITCH - 3 WAY 4 TOGGLE SWITCH - 4 WAY K TOGGLE SWITCH - KEY OPERATED T TOGGLE SWITCH - HORSE POWER RATED MANUAL MOTOR STARTER WITH THERMAL OVERLOAD PROTECTION P TOGGLE SWITCH - PILOT LIGHT D DIMMER SWITCH - 20 AMP, 120/277VAC D DIMMER SWITCH - 3 WAY 3 4D DIMMER SWITCH - 4 WAY OC1 WALL OCCUPANCY SENSOR - 1 BUTTON CONTROL OC2 WALL OCCUPANCY SENSOR - 2 BUTTON CONTROL OC3 WALL OCCUPANCY SENSOR - DUAL RELAY FOR EXHAUST FAN CONTROL OC CEILING OCCUPANCY SENSOR VS1 WALL VACANCY SENSOR - 1 BUTTON CONTROL VS2 WALL VACANCY SENSOR - 2 BUTTON CONTROL LC LOW VOLTAGE LIGHTING CONTROLLER T 0 - 3 HOUR TIMER SWITCH - 20 AMP, 120/277VAC INFORMATION SYSTEMS DESCRIPTIONSYMBOL VOICE AND DATA ONLY OUTLET WAP - WIRELESS ACCESS POINT FLOOR BOX - VOICE AND DATA CEILING - VOICE AND DATA TELECOMMUNICATIONS EQUIPMENT RACK X R - ROUGH-IN ONLY # - QUANTITY OF JACK(S) AND CABLE(S) "X" DENOTES AS FOLLOWS: LIGHTING DESCRIPTION NO SHADING INDICATES NORMAL POWER SYMBOL 24" x 24" LIGHTING FIXTURE 12" x 48" LIGHTING FIXTURE HALF SHADED INDICATES LIFE SAFETY POWER FULL SHADED INDICATES EMERGENCY POWER 12" x 96" LIGHTING FIXTURE 6" x 96" LIGHTING FIXTURE 6" x 48" LIGHTING FIXTURE 6" x 36" LIGHTING FIXTURE 6" x 24" LIGHTING FIXTURE 8" DOWNLIGHT 6" DOWNLIGHT 4" DOWNLIGHT WALL MOUNTED LIGHT CEILING EXIT LIGHT (DUAL FACED) CEILING EXIT LIGHT (SINGLE FACE) WALL EXIT LIGHT EXIT LIGHT DIRECTIONAL ARROWS WALL EMERGENCY BATTERY LIGHT WALL EXIT WITH EMERGENCY LIGHTS CEILING EMERGENCY BATTERY LIGHT WALL EXIT WITH INTERIOR AND EXTERIOR EMERGENCY LIGHTS EXTERIOR POLE LIGHT (ONE HEAD) EXTERIOR POLE LIGHT (TWO HEADS) EXTERIOR POLE LIGHT (THREE HEADS) EXTERIOR POLE LIGHT (FOUR HEADS) EXTERIOR POLE LIGHT (TOP MOUNT) EXTERIOR BOLLARD NEUTRAL GROUND RACEWAY SYSTEM DESCRIPTION PHASE CONDUCTORS SYMBOL LIGHT/SCREENED SOLID OR DASHED LINES INDICATE EXISTING TO REMAIN HEAVY CONTINUOUS LINES INDICATE NEW WORK LINE SYMBOLS HEAVY DASHED LINES INDICATE EXISTING TO BE REMOVED J JUNCTION OR PULL BOX PUSHBUTTON OR PUSH PLATE PAD MOUNTED TRANSFORMER BRANCH PANELBOARD - SURFACE MOUNT COMBINATION MOTOR CONTROLLER / DISCONNECT DISCONNECT SWITCH - NON-FUSED MOTOR CONTROLLER DISCONNECT SWITCH - FUSED MOTOR ("X" DENOTES HORSEPOWER) GROUND CONNECTION ELECTRIC THERMOSTATT DESCRIPTION MOLDED CASE CIRCUIT BREAKER ELECTRICAL EQUIPMENT SYMBOL GROUND POINT GROUND ROD X PC PHOTO CELL SUSPENDED TRANSFORMER DISTRIBUTION PANELBOARD BRANCH PANELBOARD - RECESSED MOUNT AUTOMATIC TRANSFER SWITCHN E L TELECOM TERMINAL BOARD GROUND BAR GENERATOR TV AV TV SYSTEM OUTLET AUDIO/VISUAL CONTROLLER CLOCK SYSTEM OUTLETC M M MICROPHONE INPUT RECEPTACLE - WALL MOUNTED SPEAKER - WALL MOUNTED SPEAKER - CEILING MOUNTED VOLUME CONTROL MICROPHONE INPUT RECEPTACLE - CEILING MOUNTED S S V M D S E P CB CP L Z W R A N NC IC X MTV CCTV DR ES IC MI ML CR MD DC PB K BS DS SM SS DE PC PC P IR RF CL WL 2X NURSE ASSIST NURSE ASSIST/CODE BLUE DOOR SECURITY SYSTEM SYMBOL DESCRIPTION DOOR BUZZER SECURITY DOOR ALARM MAGNETIC LOCK CCTV MONITOR OUTLET ELECTRIC DOOR OPENER ELECTRIC DOOR STRIKE INTERCOM UNIT FLUSH MTD. MASTER INTERCOM AND DIRECTORY UNIT MOTION DETECTOR CCTV COAXIAL CABLE OUTLET AND POWER OUTLET SECURITY CARD READER SECURITY CONTROL PANEL SECURITY DOOR CONTACTS SECURITY EXIT PUSH BUTTON SECURITY KEYPAD BIOSCAN ACCESS PAD CAMERA DUTY STATION DESCRIPTION MASTER STATION STAFF STATION STAFF LOCATOR STATION CODE BLUE STATION SYMBOL ROOM READY INDICATOR REMOTE ANNUNCIATOR NURSE STATION INPUT JACK BED CONTROL CABLE/INTERCONNECT JACK NURSE CALL SYSTEM PATIENT STATION - SINGLE OUTLET EMERGENCY/BATH STATION ZONE LIGHT WALL MOUNTED DOME LIGHT CODE PINK STATION NURSE AUXILIARY JACK TELEMETRY ANTENNA LOCATION CEILING MOUNTED DOME LIGHT SECURITY DUTY STATION SECURITY STAFF STATION SECURITY MONITOR SECURITY DOOR EGRESS PULL CORD PULL CORD WITH ALARMA PATIENT STATION - SINGLE OUTLET WITH CODE / STAFF ASSIST BUTTONE TRACKING SENSOR (IR) TRACKING SENSOR (RF) DOUBLE NURSE AUXILIARY JACK NAC FIRE ALARM NOTIFICATION APPLIANCE CONTROL PANEL WAP X X RECEPTACLE ABOVE COUNTERTOP AT +2" ABOVE BACKSPLASH TO BOTTOM OF DEVICE. COORDINATE WITH CASEWORK TO BE INSTALLED. RECEPTACLE INSTALLED BELOW COUNTERTOP AT +18" A.F.F. COORDINATE WITH CASEWORK TO BE INSTALLED. X RECEPTACLE LEGEND DESCRIPTIONABBREVIATION ABBREVIATION DESCRIPTION FXX FEEDER SIZE. (REFER TO FEEDER SCHEDULE FOR ADDITIONAL INFORMATION (APPLY TO ALL ELECTRICAL SHEETS) 1.PROVIDE SUPPORT WIRES FOR ALL LIGHT FIXTURES. 2.COORDINATE INSTALLATION OF LIGHT FIXTURES WITH ARCHITECTURAL REFLECTED CEILING PLAN, HVAC EQUIPMENT, DUCTWORK, PIPING AND SUPPORTS. 3.ELECTRICAL CONTRACTOR SHALL VERIFY THE EXISTING CONDITIONS AT THE PROJECT SITE BEFORE SUBMITTING COST PROPOSAL. 4.ELECTRICAL CONTRACTOR SHALL REFER TO ARCHITECTURAL DRAWINGS TO FAMILIARIZE HIMSELF WITH EXTENT OF REMODELING / ALTERATION WORK. 5.ALL WORK SHALL CONFORM TO OR EXCEED THE MINIMUM REQUIREMENTS OF THE CURRENT ANSI / NFPA 70 WITH STATE AMENDMENTS, ENERGY CODE, ANSI / IEEE C2 AND ALL FEDERAL, STATE, LOCAL AND MUNICIPAL CODES AND ORDINANCES. THE ELECTRICAL SUBCONTRACTOR SHALL COMPLY WITH THE DIRECTIONS OF ALL AUTHORITIES HAVING JURISDICTION. 6.INSTALL WORK USING PROCEDURES DEFINES IN NECA STANDARDS OF INSTALLATION. ALL WORK SHALL PRESENT A NEAT MECHANICAL APPEARANCE WHEN COMPLETED. 7.REFER TO THE ARCHITECTURAL DRAWINGS FOR CEILING WORK BY THE GENERAL CONTRACTOR. COORDINATE ALL ELECTRICAL WORK. 8.THE ELECTRICAL SUBCONTRACTOR SHALL PROVIDE ALL FLOOR, WALL, AND CEILING PENETRATIONS TO COMPLETE HIS / HER WORK. PROVIDE PROPER FIRE SAFEING FOR ALL PENETRATIONS MADE. PROVIDE APPROPRIATE SEALANT (I.E. FIRESAFEING) TO MAINTAIN CONSTRUCTION INTEGRITY FOR ANY PENETRATIONS THROUGH FLOORS, STRUCTURAL CEILING, AND FIRE WALLS. 9.COORDINATE ALL ELECTRICAL WORK WITH ALL OTHER TRADES TO ENSURE EFFECTIVE AND EFFICIENT OVERALL INSTALLATION. 10.COORDINATE ALL ELECTRICAL SYSTEM DOWNTIME WITH THE OWNER AND OTHER TRADES. IT IS MANDATORY THAT THE EXISTING BUILDING REMAIN IN CONTINUOUS AND NON-INTERRUPTED OPERATION DURING THE REMODELING / ALTERING OF THE EXISTING BUILDING. THE SPECIFIC AREA(S) BEING REMODELED / ALTERED AT ANY TIME ARE OBVIOUSLY EXCLUSIVE OF THE STATEMENT. SERVICES TO EXISTING BUILDING SHALL BE KEPT ON CONTINUOUS OPERATION INCLUDING POWER, FIRE ALARM, LIGHTING, TELEPHONE, ETC. DOWNTIME OF THESE SYSTEMS SHALL BE MINIMIZED. WEEKEND AND AFTER HOURS WORK MAY BE REQUIRED TO PREVENT OR MINIMIZE INTERFERENCE WITH OWNERS OPERATION. 11.CONTRACTOR SHALL WORK CLOSELY WITH THE OWNER TO IDENTIFY ALL SYSTEMS WIRING, DEVICES, ETC. THAT MUST REMAIN OPERATIONAL DURING CONSTRUCTION. COORDINATE ALL DEMOLITION WITH THE OWNER PRIOR TO ANY DEMOLITION WORK. 12.THE LOCATION OF NEW RECEPTACLES, PHONE / DATA JACKS, AND ROOM EQUIPMENT SHOWN ON THESE DRAWINGS ARE APPROXIMATE. FINAL LOCATIONS WILL BE DETERMINED WITH THE ARCHITECT DURING THE CONSTRUCTION PHASE. 13.IN REMODELED / ALTERED AREA ANY FEEDERS, CONDUITS, BRANCH CIRCUITS, SIGNAL AND TELEPHONE CIRCUITS, ETC. PASSING THROUGHOUT THE REMODELED / ALTERED AREAS TO SERVE (OR BE SERVED FROM EXISTING ADJACENT, REMOTE, OR SURROUNDING THAT ARE TO REMAIN) SHALL BE RETAINED AND KEPT OPERATIONS AND SHALL BE REROUTED IN ALL CASES WHERE THEY INTERFERE WITH ANY NEW WORK OR USAGE TO BE ACCOMPLISHED IN THE REMODELED / ALTERED AREA. 14.WHERE DEVICES ARE OMITTED FROM PRESENT BRANCH CIRCUITS, THE REMAINING DEVICE SHALL BE REWIRED. IF NEEDED AND AS REQUIRED, TO REMAIN IN THEIR RESPECTIVE CIRCUITS AND IN OPERATING CONDITION. 15.ALL NEW EQUIPMENT SHALL BE SUBMITTED FOR APPROVAL PRIOR TO ORDERING. 16.PHYSICAL SIZES AND LOCATIONS OF ALL MECHANICAL EQUIPMENT SHOWN ON THESE DRAWINGS ARE APPROXIMATE. COORDINATE ELECTRICAL WORK FOR THIS EQUIPMENT WITH THE OTHER TRADES. 17.ALL BRANCH CIRCUITS SHALL UTILIZE SEPARATE INDEPENDENT NEUTRAL CONDUCTORS. DO NOT COMBINE NEUTRAL CONDUCTORS. 18.ALL FEEDER NEUTRAL / GROUNDED CONDUCTORS SHALL BE CONSIDERED CURRENT CARRYING. DERATE MULTIPLE CONDUCTORS IN A RACEWAY ACCORDINGLY WITH NEC TABLES. 19.INSTALL ALL CONDUITS, RACEWAYS, AND CABLE TRAY FOR MAXIMUM HEAD CLEARANCE IN MECHANICAL AREAS. 20.ALL DEVICES SHOWN ON THESE DRAWINGS TO BE REMOVED SHALL BE REMOVED COMPLETE INCLUDING ALL ASSOCIATED CONDUIT AND WIRING BACK TO SOURCE UNLESS OTHERWISE NOTED. ALL CIRCUIT BREAKERS OR EQUIPMENT MADE SPARE BY THE DEMOLITION SHALL BE TURNED OFF AND MARKED SPARE. IT IS THE INTENT THAT ALL EXISTING ELECTRICAL DEVICES, CONDUIT, WIRING, ETC. IN THIS SPACE THAT ARE NOT REUSED AND ARE ABANDONED SHALL BE REMOVED COMPLETE. CONTRACTOR SHALL FIELD VERIFY EXACT REQUIREMENTS. NOT ALL DEVICES ARE SHOWN ON THIS DRAWING. 21.ALL DEVICES AND LIGHT FIXTURES SHOWN TO BE REMOVED FROM EXISTING BLOCK WALLS THAT ARE NOT REUSED SHALL HAVE BLANK COVERS INSTALLED. 22.ALL DEVICES SHOWN TO BE REMOVED FROM EXISTING WALLS THAT REMAIN SHALL HAVE DEVICES AND ASSOCIATED CONDUIT REMOVED AND WALL SHALL BE PATCHED. 23.REFER TO MECHANICAL DEMOLITION PLANS FOR ALL EQUIPMENT THAT IS TO BE REMOVED. REMOVE ALL ASSOCIATED CONDUIT AND WIRING TO THESE DEVICES. 24.TELEVISION SYSTEM: REMOVE ALL TELEVISION SYSTEM DEVICES AND WIRING IN AREAS OF DEMOLITION THAT ARE INSTALLED IN WALLS OR CEILINGS. ALL OTHER TELEVISION WIRING, EQUIPMENT AND DEVICES SHALL REMAIN. COORDINATE REMOVAL OF THIS SYSTEM AND ITS COMPONENTS WITH THE OWNER PRIOR TO WORK. 25.TELEPHONE / DATA SYSTEM: REMOVE ALL TELEPHONE / DATA SYSTEM DEVICES AND WIRING IN AREAS OF DEMOLITION THAT ARE INSTALLED IN WALLS OR CEILINGS. ALL OTHER TELEPHONE / DATA WIRING, EQUIPMENT AND DEVICES SHALL REMAIN. COORDINATE REMOVAL OF THIS SYSTEM AND ITS COMPONENTS WITH THE OWNER PRIOR TO WORK. 26.CCTV SYSTEM: REMOVE ALL CCTV SYSTEM DEVICES AND WIRING IN AREAS OF DEMOLITION THAT ARE INSTALLED IN WALLS OR CEILINGS. ALL OTHER CCTV WIRING, EQUIPMENT AND DEVICES SHALL REMAIN. COORDINATE REMOVAL OF THIS SYSTEM AND ITS COMPONENTS WITH THE OWNER PRIOR TO WORK. 27.NURSE CALL SYSTEM: REMOVE ALL NURSE CALL SYSTEM DEVICES AND WIRING IN AREAS OF DEMOLITION THAT ARE INSTALLED IN WALLS OR CEILINGS. ALL OTHER NURSE CALL WIRING, EQUIPMENT AND DEVICES SHALL REMAIN. COORDINATE REMOVAL OF THIS SYSTEM AND ITS COMPONENTS WITH THE OWNER PRIOR TO WORK. 28.FIRE ALARM SYSTEM: REMOVE ALL FIRE ALARM SYSTEM DEVICES AND WIRING IN AREAS OF DEMOLITION THAT ARE INSTALLED IN WALLS OR CEILINGS. ALL OTHER FIRE ALARM WIRING, EQUIPMENT AND DEVICES SHALL REMAIN. COORDINATE REMOVAL OF THIS SYSTEM AND ITS COMPONENTS WITH THE OWNER PRIOR TO WORK. 29.ALL LIGHT FIXTURES SHOWN WITH EMERGENCY BATTERY BALLASTS SHALL HAVE UNSWITCHED "HOT" WIRE INSTALLED TO BALLAST. 30.NEW DEVICES SHOWN TO BE INSTALLED ON EXISTING DRYWALL WALLS SHALL BE INSTALLED FLUSH IN WALL WITH CONDUIT AND WIRING CONCEALED. CUT AND PATCH EXISTING WALLS AS REQUIRED. 31.NEW DEVICES SHOWN TO BE INSTALLED ON EXISTING BLOCK WALLS SHALL BE INSTALLED SURFACE MOUNTED AND IN SURFACE MOUNTED WIREMOLD PAINTED TO MATCH WALL. 32.WIRING SHALL BE INSTALLED ABOVE ACCESSIBLE CEILINGS AND IN DRYWALL WALLS WHERE POSSIBLE. 33.WIRING THAT IS TO BE INSTALLED IN AREAS WHERE THERE ARE NO CEILINGS SHALL BE INSTALLED EXPOSED. CABLING SHALL BE INSTALLED NEATLY AND AT RIGHT ANGLES TO STRUCTURE. WIRING SHALL BE INDEPENDENTLY SUPPORTED AS REQUIRED. WIRING SHALL NOT LAY OVER OTHER TRADES. 34.NEW DEVICES SHALL MATCH EXISTING DEVICES AND COVERPLATES. 35.WHERE OCCUPANCY SENSORS ARE INDICATED ON PLANS, THE ENTIRE ROOM SHALL BE COVERED. MANUFACTURER IS RESPONSIBLE FOR SENSOR LAYOUT. ADDITIONAL SENSORS REQUIRED DUE TO LACK OF COVERAGE SHALL BE THE RESPONSIBILITY OF THE ELECTRICAL CONTRACTOR. PROVIDE QUANTITY AS REQUIRED. CEILING AND WALL MOUNTED SENSORS SHALL BE DUAL TECHNOLOGY TYPE. SENSORS SHALL INCLUDE ALL POWER SUPPLIES AND RELAYS NECESSARY TO CONTROL LIGHT FIXTURES IN ROOM / AREA. SENSORS SHALL OPERATE IN "VACANCY" MODE - MANUAL ON / AUTO OFF. TYPE OC SQUARE - INDICATES A WALL MOUNTED SINGLE CIRCUIT SENSOR WITH 1 SWITCH, TYPE ROUND OC INDICATES A CEILING MOUNTED SENSOR. PROVIDE A SET OF AUXILIARY CONTACTS ON ALL WALL AND CEILING MOUNTED OCCUPANCY SENSORS FOR SENSOR STATUS FOR TEMPERATURE CONTROL. 36.ELECTRICAL CONTRACTOR SHALL BE RESPONSIBLE FOR HIS OWN DEMOLITION, REMOVAL, CAPPING, STORING, ABANDONING, DISCONNECTION, RELOCATING AND RECONNECTION OF EXISTING ELECTRICAL EQUIPMENT AND MATERIAL. ALL CUTTING, PATCHING, REPAIRING, REPLACEMENT AND REFINISHING, SHALL MATCH THE EXISTING CONSTRUCTION AS NEARLY AS POSSIBLE. 37.ALL WIRING (POWER, LIGHTING) NOT REUSED FOR REMODELING AREAS SHALL BE COMPLETELY REMOVED BACK TO ASSOCIATED PANELS. 38.THE OWNER SHALL HAVE THE FIRST CHOICE TO ACCEPT EXISTING DEVICES BEING REMOVED. 39.REMOVE ALL ABANDONED CONDUITS, BOXES AND WIRING WITHIN PROJECT AREA. 40.FIRE ALARM SYSTEM SHALL BE MAINTAINED DURING PROJECT. 41.CEILING MOUNTED DEVICES TO REMAIN SHALL BE SUPPORTED FROM STRUCTURE DURING CONSTRUCTION AND REINSTALLED IN NEW CEILING. 42.ARRANGEMENTS SHALL BE MADE WITH OWNER REPRESENTATIVE TO COORDINATE FIRE ALARM SYSTEM OUTAGE. 43.CONTRACTOR SHALL PROTECT EXISTING CABLES DURING ALL PHASES OF CONSTRUCTION. 44.ALL DEVICES (EXIT SIGNS, FIRE ALARM, LIGHTING, ETC) THAT ARE TAKEN OUT OF SERVICE AND NOT REUSED SHALL BE RETURNED TO THE OWNER. 45.ALL RECEPTACLES SHALL BE HOSPITAL GRADE AND SAFETY / TAMPERPROOF TYPE. SCP GENERAL NOTES 24" x 48" LIGHTING FIXTURE 12" x 36" LIGHTING FIXTURE 12" x 24" LIGHTING FIXTURE 12" x 12" LIGHTING FIXTURE Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:10:12 PMElectrical Symbols and Abbreviations E001 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation ForREV. DATE Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:10:35 PMElectrical Specifications E002 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation ForREV. DATE OPEN TO STRUCT. OPEN TO STRUCTURE OPEN TO STRUCT. OPEN TO STRUCTURE OPEN TO STRUCTURE OPEN TO STRUCTURE OPEN TO STRUCTURE, OPEN TO STRUCT. OPEN TO STRUCTURE OPEN TO STRUCTURE OPEN TO STRUCT. ACT 2 OPEN TO STRUCT. PULL CHAIN FOR AUTOMATIC DOORS PULL CHAIN FOR AUTOMATIC DOORS ACT 2 ACT 2 PULL CHAIN FOR AUTOMATIC DOORS OPEN TO STRUCTURE OPEN TO STRUCTURE OPEN TO STRUCT. OPEN TO STRUCTURE 2 HOUR FIRE-RATED CEILING 2 HOUR FIRE-RATED CEILING PLASTER SOFFIT W/ CONTROL JOINTS AT 10'-0" O.C., TYP. +8'-10 5/8" ABOVE 100'-0" ST02/ SHELF ANGLE PAINTED OPEN TO STRUCTURE HOR. ENCL. AT BOTTOM OF SHAFT HOR. ENCL. AT BOTTOM OF SHAFT OPEN TO STRUCT. HOR. ENCL. AT BOTTOM OF LIGHT POWER POLES, TYP. +10'-0" AFF PA SYSTEM SPEAKER PA SYSTEM SPEAKER +10'-0" AFF PA SYSTEM SPEAKER PA SYSTEM SPEAKER EXPOSED TO STRUCTURE ACT 2 ACT 2 ACT 2 ACT 2 ACT 2 OPEN TO STRUCTURE SLOPED CEILING OPEN TO STRUCTURE STERIS 1E WORKCART STERIS 1E WORKCART STERIS 1E WORKCART STERIS 1E WORKCART M L K J H G F E.4 191817.217161514131211.39.99.7987654 M L K J H G F E.4 G.3 F.6 4.3 G.3 F.6 E E 3 9.14.6 D 119.3 10 E.2 D C B A M.2 E.2 D.9 C B A 12.5 D.1 D.4 16.3 D.1 D.3D.3 D.4 R7 441435 447010447040 447005 447040 447030 443040 443040 447080 447015 441185 447005 443005 441185 443005 443005 443050 441105 441105 443005 447005 447005 447015 447015 447005 443005 441105441105441105 441105 441105 441105 441105 441105 447005 443005 443005 447005 443005 443005 441150443015 443005 443005 443005 443005 443005 443005 443005 443050 443040 441150447015 441195 441150 441150 441150 441005 441150 441150 441150 441150 441150441150441150 447005 447020 443050443043 443050 443050 447005 447005 441185 441185 441185 441185 447015 447040 447035 447040 447040 447040 447040 441185 441185 441185 441185 441185 441185 441185 447005 447015 447015 443050 447005 447040 447005 447005 441185 447005 447005 447015 447015 447005 447005447005 447005 447005 447005 447040 447005 447015 447015 447005 447005447005 447005 447005 447030 447005 447005 447015447015447005447005447005447005447005447005 447040 447035 447015 447040 447040 447005 447005 447035447040447040 447040 447040 441100 447005 441100 441100 441100 447005 441100 447005 447005 447005 447005 441100 441100 441100441435 B003 B012BB012C B011-2 B035-2 ELEV 5 ELEV 4 ELEV 7 ELEV 6 SH01 SH03 C022C C022B C022A B021A B065A B050Q B050D C033D B1-LL B050K C030 C0C17 C0C10 B0C02 B0C16 B0C11 C041 ELEV 9 C024 C1-LL C025 C026 C2-LL C3-LL C038 C031 C032 C0C09 C0C01 C0C02 C0C07 ELEV 8 C0C06C028 C027 C029 C0C05 C0C03 C0C04 C030A C026BC026AC025A C025C C025D C025E C025B C025F C043 C0C16 C0C15 C042 C040 C039 C037C036 C0C08 C033 C034 C035 C033C C033B C033A C0C14 C0C11 C024A C023 C018C019 C017 C009 C0C13 C0C12 C016A C016 C015 C014 C013 C010C011C012 C001 C002 C021C020B C020 C020A B044 ELEV 10 ELEV 14B050P B050N ELEV 15 B050 B050L B050H B0C03 B043 B035G B035-1 B035J B035K B035H B0C20 B0C17 ELEV 13 B2-LL B046 B050G B050E B048 B047 B050F B050M B042 B040 B039 B041 ELEV 11 B045B3-LL B0C13 B0C01 B0C12 B038 B065 B065B B050C B050A B0C15 B0C04 B064 B017 B0C05 B016 B015 B063AB063B063B B063C B062 B061C B035E B061B B061 B061A B060B060A B0C09 B0C08 B013B012A B012 B0C07 B014 B0C06 B018 B018AB019B020B021B022B023B024B025 B035D B035C B035B B0C14 B035A B037 B036 B034B034AB032 B031 B030 B004 B026 B007 B007B B007A B027 B008 B009 B009A B010 B011AB006A B006 B005B003 WORK Dialysis OFFICEOFFICE OFFICE KITCHEN Cafeteria OFFICE OFFICE OFFICE OFFICE ES CLOS CENTL PROC ELEV MACH RECEIV STAIR STERILIZ STOR CORRIDOR CORRIDOR CORRIDOR ELEV LOBBY CORRIDOR STOR ELEVATOR DATA 1 STAIR PHARMACY STOR STAIR STAIR CLEAN LIN MECH ELEC CORRIDOR CORRIDOR CORRIDOR CORRIDOR ELEVATOR ELEV LOBBYTRASH LINEN OFFICE CORRIDOR CORRIDOR CORRIDOR WORK TLT STFLOUNGEWORK WORK LAB WORK OFFICE ANTE CLASS CORRIDOR CORRIDOR CARTS TRASH RECEIV DOC MORGUEMAIL CORRIDOR CENTL PROC STOR STOR OFFICE OFFICE BREAK CORRIDOR CORRIDOR UPS STOR BIOHAZARDES CLOS BLOOD BANK LAB CORRIDOR CORRIDOR OFFICE OFFICE OFFICE OFFICE STOR TLT STFLOUNGECONFERENCE MECH SHOP AREA SERVERSOFFICE WORK STOR STOR ELEVATOR ELEVATORMECH STERILIZ ELEVATOR DECONTAM STOR STOR CORRIDOR STOR FREEZER KITCHEN Patient REF STOR REF STORREF STOR ELEV LOBBY CORRIDOR ELEVATOR STAIR DECONTAM LOCKERS OFFICE CLEAN PROC ANTE WORK EQ ELEC TRASH LINEN MDF ELEVATOR MECHSTAIR CORRIDOR CORRIDOR CORRIDOR STOR CORRIDOR TRASH LIN SERVICE ELEV MACH CORRIDOR CORRIDOR OFFICE ES CLOS CORRIDOR ES CLOS SHELL VESTLOCKERSSHOWER TLT STF LOUNGE TLT STF STOR SHOWER LOCKERS VEST STORELEV MACH CORRIDOR CORRIDOR WORKOFFICE OFFICE CORRIDOR STOR CORRIDOR OFFICE OFFICEOFFICETLT STFOFFICEOFFICEOFFICEOFFICEOFFICE STOR DISH WASH ES CLOS CORRIDOR STOR MECH MECH OFFICEOFFICETLT STF OFFICE OFFICE EQ STOR COPY KITCHEN LOCKERS TLT STF OFFICE OFFICE RECEPT ALCOVE CONFERENCE STORRECEPT WORK CLEAN PROCWORK Dialysis R8 UP UP UP UP UP UP AREA OF CONSTRUCTION True NorthPlan NorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates KEY PLAN IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:10:58 PMOverall Ground Floor Plan E100 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation For 1/16" = 1'-0"1 Overall Ground Floor Plan APPROXIAMTE LOCATION OF CATH LAB #2 ROOM B168 ON FIRST FLOOR APPROXIMATE LOCATION OF EXISTING PANEL 'CBP-CATH B168' ON FIRST FLOOR EXISTING PANEL 'GHUPSEQDPA1' EXISTING UPS 'GUPSEQA1' REV. DATE REF.REF. REF. REF. REF. 1 2 3 4 4.3 4.64.74.95 6 7 8 9 9.19.3 9.7 9.910 11 11.3 12 13 14 14.915 1616.116.3 17 17.2 19 A B C DD.1 D.3 E E.2 E.4 F F.6 G G.3 H J K L M 18 D.9 M.2 ELEC B149 TELE B150 N.C. B151 CTRL / READ B167 CATH LAB #2 B168 AREA OF CONSTRUCTION True NorthPlan NorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates KEY PLAN IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:11:07 PMOverall First Floor Plan E110 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation For 1/16" = 1'-0"1 Overall First Floor Plan REV. DATE D DDD D 14.9 15 16 16.1 K L 1 1 14.9 15 16 16.1 K L F1-EM F1 F1 F1-EM F1-EMF1-EM F1 F1 F1 F1-EM F1 F1-EM F1 F1 F1-EM F1-EM F1 F1 a a a a a a d dd d a a a a a a dd 3Da 3Da F2F2 F2 F2 F2 F2 3 3 Db c c cc b b 3Dc 3Dc 2 2 4 44 5 5 5 5 5 5 AREA OF CONSTRUCTION True NorthPlan NorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates KEY PLAN IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:11:14 PMFirst Floor Lighting Plans E210 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation For 1/4" = 1'-0"1 First Floor Lighting Demolition Plan 1/4" = 1'-0"2 First Floor Lighting Plan PLAN NOTES 1 DISCONNECT AND REMOVE EXISTING LIGHT FIXTURES AND SWITCHES SHOWN AS DASHED IN THIS ROOM. MAINTAIN ALL WIRING / CONDUIT IN AREA FOR RESUSE. REFER TO DETAIL 2 ON THIS SHEET FOR ADDITIONAL INFORMATION. 2 REFER TO PHILIPS EQUIPMENT SITE SPECIFIC DRAWINGS FOR ROOM LAYOUT, SPECIFICATIONS, DETAILS AND ADDITIONAL ELECTRICAL SCOPE FOR THIS ROOM. ALL DRAWINGS, ROUGH-INS, AND SPECIFICATIONS ARE NOT REPEATED ON THIS DRAWING. ALL ELECTRICAL WORK SHOWN ON THE PHILIPS EQUIPMENT DRAWINGS INDICATED AS BY CONTRACTOR OR CUSTOMER SHALL BE INCLUDED IN ELECTRICAL SCOPE. 3 CONNECT NEW LIGHT FIXTURES IN THIS ROOM TO EXISTING CRITICAL POWER LIGHTING CIRCUIT MAINTAINED DURING DEMOLITION. MODIFY / EXTEND EXISTING WIRING / CONDUIT AS REQUIRED. 4 EXISTING IN-USE WARNING LIGHT TO REMAIN. PROVIDE NEW CONDUIT AND WIRING AS REQUIRED TO CONNECT TO NEW CATH LAB EQUIPMENT. MODIFY / EXTEND EXISTING WIRING / CONDUIT AS REQUIRED. 5 LIGHT FIXTURE TO BE CONTROLLED WITH CATH LAB FOOT PEDAL. PROVIDE ALL DEVICES AS SHOWN ON THE PHILIPS DRAWINGS FOR INTERFACE WITH CATH LAB EQUIPMENT. REV. DATE V PMR SHB J S S SSJ J S S V PMR SHS S S S B VV14.9 15 16 16.1 K L 1LUPSEQA1 CBP-CATH B168 GROUND BAR 'ERB'4 5 5 5 11 6 3 3 6 6 6 57 13 8 8 111111 11 11 11 11 11 11 1111 4 10 12 14 'TR' 'TR2' 14 15 10 15 14.9 15 16 16.1 K L CBP-CATH B168 1LUPSEQA1 EXISTING CABLE TRAY EXISTING CABLE TRAY2 1 11 1 1 1 1 1 1 1 11 11 1 1 1 1 1 1 1 1 1 11 1 1 9 9 2 14 H 1LNDPA2 1LLSA1 1LEQA1 1LCRA1 1LCRA4 1LNRA1 1LNRA2 1HCRA1 1HLSA1 1HNLA1 1HEQA1 1LUA2 1LNRA3 1LNRA6 1LNRA9 SW2 SW1 1LNRA11 DATA RACK DATA RACK DATA RACK CARD READER BACKBOARD FAAP FAAP FAAP TELEMETRY BACKBOARD NURSE CALL CENTRAL EQUIPMENT TV SYSEM EQUIPMENT PATIENT MONITORING EQUIPMENT SECURITY SYSTEM RACK FIRE ALARM ANNUNCIATOR PANEL(S) AREA OF CONSTRUCTION True NorthPlan NorthMOB HOSPITAL CENTRAL PLANT Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates KEY PLAN IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:11:20 PMFirst Floor Power and Systems Plans E310 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation For 1/4" = 1'-0"1 First Floor Power and Systems Plan 1/4" = 1'-0"2 First Floor Power and Systems Demolition Plan 1/4" = 1'-0"3 Enlarged Room B149, B150 & B151 Power and Systems Plan PLAN NOTES 1 EXISTING TO REMAIN. 2 DISCONNECT AND REMOVE EXISTING RECEPTACLES, TELECOM, SPEAKERS, ETC. SHOWN AS DASHED IN THIS ROOM. MAINTAIN ALL WIRING / CONDUIT IN AREA FOR RESUSE. REFER TO DETAIL 2 ON THIS SHEET FOR ADDITIONAL INFORMATION. 3 REFER TO PHILIPS EQUIPMENT SITE SPECIFIC DRAWINGS FOR ROOM LAYOUT, SPECIFICATIONS, DETAILS AND ADDITIONAL ELECTRICAL SCOPE FOR THIS ROOM. ALL DRAWINGS, ROUGH-INS, AND SPECIFICATIONS ARE NOT REPEATED ON THIS DRAWING. ALL ELECTRICAL WORK SHOWN ON THE PHILIPS EQUIPMENT DRAWINGS INDICATED AS BY CONTRACTOR OR CUSTOMER SHALL BE INCLUDED IN ELECTRICAL SCOPE. 4 PROVIDE GROUND BAR IN EQUIPMENT ROOM AS REQUIRED IN PHILIPS EQUIPMENT SITE SPECIFIC DRAWINGS. 5 PROVIDE AND CONNECT NEW EPO BUTTON COMPLETE. REFER TO PHILIPS EQUIPMENT SITE SPECIFIC DRAWINGS FOR ADDITIONAL INFORMATION. PROVIDE NEW WIRING AND CONDUIT AS REQURIED. 6 NEW TELECOMMUNICATIONS ROUGH-IN. PROVIDE 1-1/4" CONDUIT FROM BOX TO CABLE TRAY. TERMINATE CONDUIT WITH BUSHING AND PROVIDE PULL STRING. 7 MED GAS PEDESTAL. COORDINATE LOCATION WITH PHILIPS AND PHILIPS EQUIPMENT. PROVIDE (3) DUPLEX RECEPTACLES, (1) TWIST LOCK RECEPTACLE, AND (4) TELECOM PORTS IN PEDESTAL. CONNECT DUPLEX RECEPTACLE POWER TO 120V, 20A, 1P CRITICAL POWER CIRCUIT MAINTAINED DURING DEMOLITION OR NEAREST CRITICAL POWER BRANCH PANEL. CONNECT TWIST LOCK POWER TO EQUIPMENT(UPS) POWER PANEL '1LUPSEQA1'. PROVIDE TELECOMMUNICATIONS CABLES TO DATA ROOM. PROVIDE ALL BREAKERS, WIRING AND CONDUIT AS REQUIRED. TWIST LOCK RECEPTACLE IS FOR LASER, VERIFY WITH OWNER EXACT RECEPTACLE CONFIGURATION. 8 CONNECT RETAINED SPEAKERS TO EXISTING SOUND SYSTEM COMPLETE. REFER TO DETAILS ON E700 FOR ADDITIONAL INFORMATION. 9 REMOVE ALL CONDUIT, WIRING, DEVICES, WIREWAY ASSOCIATED WITH EXISTING CATH LAB EQUIPMENT COMPLETE UNLESS OTHERWISE NOTED. 10 PROVIDE BLUETOOTH / WIFI SPEAKER AT LOCATION SHOWN. SPEAKERS SHALL HAVE THE FOLLOWING FEATURES: 1. HARD WIRED POWER. 2. WALL MOUNT CAPABLE. 3. CAPABILITY TO PLAY ON (2) SPEAKERS IN DIFFERENT ROOMS. 4. SMART PHONE APP INCLUDED. 5. SIMILAR TO SONOS 'PLAY:1' OR BOSE 'SOUNDTOUCH 10 X2'. 11 CONNECT NEW RECEPTACLE TO DEDICATED 120V, 20A, 1P CRITICAL POWER CIRCUIT MAINTAINED DURING DEMOLITION OR NEAREST CRITICAL POWER BRANCH PANEL. PROVIDE ALL BREAKERS, WIRING AND CONDUIT AS REQUIRED. 12 PROVIDE EQUIPOTENTIAL GROUNDING FOR ALL DEVICES, EQUIPMENT, METAL CABINETS, DOOR FRAMES, ETC. IN THIS ROOM. PROVIDE (1) #10AWG GROUND IN 3/4" CONDUIT FROM EACH METALLIC OBJECT TO EQUIPMENT GROUNDING BUS 'PCB'. REFER TO PHILIPS EQUIPMENT SITE SPECIFIC DRAWINGS FOR ADDITIONAL INFORMATION. 13 120V/24V, 500VA TEMPERATURE CONTROL TRANSFORMER. TRANSFORMER PROVIDED AND INSTALLED BY TEMPERATURE CONTROL CONTRACTOR. CONNECT TO 120V, 20A, 1P EQUIPMENT(UPS) POWER CIRCUIT. PROVIDE ALL BREAKERS, WIRING AND CONDUIT AS REQUIRED. 14 CONNECT TO 120V, 20A, 1P CRITICAL POWER CIRCUIT MAINTAINED DURING DEMOLITION OR NEAREST CRITICAL POWER BRANCH PANEL. PROVIDE ALL BREAKERS, WIRING AND CONDUIT AS REQUIRED. 15 RECEPTACLE MOUNTED AT SAME HEIGHT AS SPEAKER. COORDIANTE EXACT LOCATION WITH OWNER PRIOR TO ROUGH-IN. CONNECT TO 120V, 20A, 1P NORMAL POWER CIRCUIT MAINTAINED DURING DEMOLITION OR NEAREST NORMAL POWER BRANCH PANEL. PROVIDE ALL BREAKERS, WIRING AND CONDUIT AS REQUIRED. REV. DATE 277/480 3P-4W GUPSEQA1 300kVA GROUND FLOOR 400A MCB GHUPSEQDPA1 3P-5W 277/480 (2) SETS OF (4) #4/0 (1) #1/0 GND (1) #1/0 ISO GND FIRST FLOOR GND + ISO GND FLYWHEEL 125A MCB CBP-CATH B168 3P-4W 277/480 GND (1) SET OF (3) #1/0 (1) #1/0 GND PHILLIPS CABINET MA (1) SET OF (3) #1/0 (1) #1/0 GND 1200A MCB 1HEQDPA1 3P-4W 277/480 GND + ISO GND (2) SETS OF (4) #4/0 (1) #1/0 GND (1) #1/0 ISO GND 6HESBA/B1ATSEQA2 GHNSBA1 SHUNT TRIP WIRING AS REQUIRED GROUND CONDUIT SIZE AND QUANTITY FEEDER SIZING TABLE F20 DESIGNATION 1212 CONDUCTOR SIZE PER CONDUIT ISOLATED NEUTRAL PHASE & 2P, 1G 1P, 1N, 1GOR 3P, 1G 2P, 1N, 1GOR 3P, 1N, 1G 3P, 3N, 1G 3P, 1N, 2G 3/4"3/4"3/4"3/4"3/4" F30 1010 3/4"3/4"3/4"3/4"3/4" F40-F50 F60 F70-F80 F90-F100 F110 F125 F150 F175 F200 F225 F250 108 3/4"3/4"3/4"1"3/4" 106 3/4"3/4"1"1"1" 84 3/4"1"1-1/4"1-1/4"1-1/4" 83 1"1"1-1/4"1-1/2"1-1/4" 62 1"1-1/4"1-1/4"1-1/2"1-1/4" 61 1-1/4"1-1/4"1-1/2"2"1-1/2" 61/0 1-1/4"1-1/2"1-1/2"2"2" 62/0 1-1/4"1-1/2"2"2-1/2"2" 63/0 1-1/4"2"2"2-1/2"2" 44/0 1-1/2"2"2-1/2"2-1/2"2-1/2" 4250 2"2"2-1/2"3"2-1/2" F300 4350 2"2-1/2"3"3-1/2"3" F350 3500 2-1/2"3"3"4"3" F400 33/0 (2) 2"(2) 2-1/2"(2) 3"(2) 2-1/2" F450 24/0 (2) 2"(2) 2-1/2"(2) 3"(2) 2-1/2" F500 2250 (2) 2"(2) 2-1/2"(2) 3"(2) 2-1/2" F600 1350 (2) 2-1/2"(2) 3"(2) 3-1/2"(2) 3" F700 500 (2) 3"(2) 3"(2) 4"(2) 3-1/2"1/0 F800 350 (3) 2-1/2"(3) 3"(3) 3-1/2"(3) 3"1/0 F900 350 (3) 2-1/2"(3) 3"(3) 3-1/2"(3) 3"2/0 F1000 500 (3) 3"(3) 3"(3) 4"(3) 3-1/2"2/0 F1200 350 (4) 2-1/2"(4) 3"(4) 3-1/2"(4) 3"3/0 F1600 500 (5) 3"(5) 3"(5) 4"(5) 3-1/2"4/0 F2000 500 (6) 3"(6) 3-1/2"(6) 4"(6) 3-1/2"250 F301 2350 2-1/2"3"3"4"3" F401 3/0 1/0 (2) 2-1/2"(2) 3"(2) 3-1/2"(2) 3" FXXX F2500 500 (7) 4"(7) 4"(7) 4"(7) 4"350 F3000 500 (8) 4"(8) 4"(8) 4"(8) 4"500 GROUND 12 BUILDING 10 10 10 8 8 6 6 6 6 6 4 4 4 3 3 2 2 1 1/0 1/0 2/0 2/0 3/0 4/0 250 2 1/0 350 500 NOTES: 1. 20 A BRANCH CIRCUITS SHALL BE SIZED FOR VOLTAGE DROP. WIRE SIZES ARE NOT INDICATED ON THE DRAWINGS TO COMPENSATE FOR VOLTAGE DROP. FOR THESE CIRCUITS, CONTRACTOR SHALL UTILIZE WIRE SIZE SHOWN ABOVE FOR DISTANCES LISTED ABOVE. 2. VOLTAGE DROP WIRE SIZES WILL BE STRICTLY ENFORCED. CONTRACTOR SHALL SUBMIT A LIST OF CIRCUITS THAT WILL EXCEED THE DISTANCES ALLOWED AND INDICATE WIRE SIZE TO BE USED PRIOR TO ANY WIRE BEING INSTALLED. 3. DO NOT SHARE NEUTRAL CONDUCTORS FOR ANY BRANCH CIRCUITS. ALL BRANCH CIRCUIT SHALL HAVE SEPARATE, INDEPENDENT NEUTRAL CONDUCTORS. 4. ALL NORMAL POWER BRANCH CIRCUIT WIRING SHALL BE INSTALLED IN CONDUIT COMPLETE. 5. ALL EMERGENCY POWER CIRCUIT WIRING SHALL BE INSTALLED IN CONDUIT COMPLETE. 6. ALL CONDUIT PENETRATIONS THRU THE FLOOR SLAB SHALL BE MADE WITH CAUTION. CONTRACTOR SHALL COORDINATE ALL HOLE LOCATIONS WITH STRUCTURAL ENGINEER PRIOR TO CUTTING ANY NEW HOLES. NEW HOLES SHALL BE ADJUSTED AS REQUIRED TO MISS REBAR AS DETERMINED BY THE STRUCTURAL ENGINEER. 7. VOLTAGE DROP IN NOT SHOWN ON THE DRAWINGS. CONTRACTOR SHALL BE RESPONSIBLE FOR ADJUSTING ALL BRANCH CIRCUIT AND FEEDER SIZES TO COMPLY WITH STATE AND LOCAL VOLTAGE DROP REQUIREMENTS. a. VOLTAGE DROP ON ALL BRANCH CIRCUITS SHALL NOT EXCEED 3%. b. VOLTAGE DROP ON ALL FEEDERS SHALL NOT EXCEED 2%. 277V 200 FEET 360 FEET 120VFEEDER SIZE TO USE F20 F30 VOLTAGE DROP FOR 20A BRANCH CIRCUITS 100 FEET 150 FEET MAXIMUM DISTANCE ALLOWED 550 FEET 885 FEET F40-50 F60 240 FEET 385 FEET Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:11:28 PMElectrical Schedules E600 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation ForLIGHT FIXTURE SCHEDULE TYPR MARK FIXTURE NAME DESCRIPTION VOLTAGE LAMP Manufacturer F1 SURGICAL DOWNLIGHT NOMINAL 6" DIA. APPURATURE x 6.5" HIGH LED DOWNLIGHT, SEMI-SPECULAR REFLECTOR AND WHITE FLANGE, EXTRUDED ALUMINUM HEAT SINK, FIVE YEAR WARRANTY, MEDIUM DISTRIBUTION, 50 DEG. CUTOFF, 0-10V DIMMING DRIVER TO 1%, SEALED BOTTOM LENS WITH CLEAR ACRYLIC LENS 277 V LED 31W 3500K KENALL - M2RDL6L OR APPROVED EQUAL F1-EM SURGICAL DOWNLIGHT NOMINAL 6" DIA. APPURATURE x 6.5" HIGH LED DOWNLIGHT, SEMI-SPECULAR REFLECTOR AND WHITE FLANGE, EXTRUDED ALUMINUM HEAT SINK, FIVE YEAR WARRANTY, MEDIUM DISTRIBUTION, 50 DEG. CUTOFF, 0-10V DIMMING DRIVER TO 1%, SEALED BOTTOM LENS WITH CLEAR ACRYLIC LENS. PROVIDE WITH INTERGRAL 90 MINUTE BATTERY PACK. 277 V LED 31W 3500K KENALL - M2RDL6L OR APPROVED EQUAL F2 DOWNLIGHT NOMINAL 4" DIA APPERTURE X 8" HIGH OPEN DOWNLIGHT, LOW IRIDESCENT SEMI SPECULAR CLEAR ALUMINUM RELFECTOR, SELF TRIM WITH WHITE FLANGE. 0-10V DIMMING DRIVER (10%-100%). 277 V 1500 LUMENS 18W 3500K GOTHAM - EVO OR APPROVED EQUAL NO SCALE1ELECTRICAL ONELINE RISER DIAGRAM Remarks: Total Connected Load (Amps):0.0 A Total Connected Load (kVA):0.0 kVA Total Load:0.0 kVA 0.0 kVA 0.0 kVA 11 12 9 10 7 8 5 ---- --0 VA 6 3 ---- -- 0 VA 4 1 PHILIPS CABINET 'MA' 125 A 3 0 VA 2 Circuit Number Circuit Description Trip Poles A B C Poles Trip Circuit Description Circuit Number General Panel Comments: Enclosure Type:Type 1 Ground:GND Main Rating:125 A Mounting:Surface Wire:4 Main Type:MCB Supplied From:Phase:3 A.I.C. Rating:42,000 Location:Voltage:480/277 Wye Branch:EQUIPMENT(UPS) Branch Panel: CBP-CATH... CATH B168 GHUPSEQDPA1 REV. DATE SUPPORT STRUCTURE NOTE:FOR STEEL STRUCTURAL SYSTEM COMBINATION BEAM CLAMP AND CONDUIT HANGER OR EQUIVALENT NOTE: 1.FOR STEEL STRUCTURAL SYSTEM. 2.PROVIDE SEISMIC BRACING MINIMUM 40' ON CENTER WHEN THE CONDUITS SUPPORT IS BELOW 12" FROM STRUCTURE. UNISTRUT CHANNEL OR EQUIVALENT CONDUIT CLAMP OR EQUIVALENT SIZE AS REQUIRED THREADED ROD SIZE AS REQUIRED BEAM CLAMP STRUTCLAMP OR EQUIVALENT BEAM CLAMP STEEL CABLE AIRCRAFT HANGER WIRE STEEL CABLE AIRCRAFT HANGER WIRE SUPPORT CONNECTED TO STRUCTURE ABOVE 12 GAUGE HANGER WIRE OR CHAIN FOR FIXTURE LAY-IN CEILING LAY-IN CEILING JUNCTION BOX W/#12 WIRE (6' MAX.) FLEXIBLE CONDUIT LAY-IN CEILING LAY-IN CEILING SEISMIC CLIP FED FROM MDP 120/208V 3P 4W. PANEL 1LN1 EQUIPMENT SERVED INFORMATION PLATE SOURCE OF POWER VOLTAGE LAMACOID PLATE NOTE:PROVIDE I.D. PLATE LABEL FOR ELECTRICAL EQUIPMENT SUCH AS MAIN SWITCHGEAR, SWITCHBOARD PANELBOARDS, AND TRANSFORMERS !WARNING Arc Flash Hazard Appropriate PPE Required Equipment Type Grounding Work Distance Availiable 3-Ph Bolted Current Flash Protection Boundary Incident Energy at 11 inches Risk Category Equipment Name: 480V Switchgear Grounded 11 inches (300 mm) 25 kA 27 inches 4.39 cal/cm2 2 Switchboard NOTE:PROVIDE WARNING LABEL FOR ALL ELECTRICAL EQUIPMENT SUCH AS MAIN SWITCHGEAR, SWITCHBOARDS, PANELBOARDS, AND TRANSFORMERS. M C FFRDRAST V AA R SFF EXISTING FIRE ALARM CONTROL PANEL FIRST FLOOR 120V FIRE ALARM POWER PROVIDE SIGNAL EXPANDER/AMPLIFIER POWER SUPPLY ON EACH FLOOR FOR SIGNAL DEVICES. LOCATE EQUIPMENT IN ELECTRICAL ROOM. PROVIDE SPARE CAPACITY TO ADD (2) SIGNAL DEVICES (TYP. OF EACH SIGNAL CIRCUIT) ADDRESSABLE RELAY FOR CONTROL PROVIDE ONE AT EACH AHU SUPPLY AND RETURN FAN STARTERS, AT EACH FIRE/SMOKE DAMPER AND AT EACH DOOR HOLD RELEASE DEVICE PROVIDE SPARE CAPACITY TO ADD 20% FUTURE DEVICES ON EACH INITIATION LOOP TYPICAL FIRE/SMOKE DAMPER TYPICAL DOOR HOLD/RELEASE DEVICE TYPICAL HVAC UNIT STARTER PROVIDE CONTROL WIRING IN CONDUIT AS REQUIRED TO OTHER DEVICES SEE FLOOR PLANS NOTES: 1. ALL FIRE ALARM SYSTEM WIRING SHALL BE INSTALLED IN CONDUIT COMPLETE. 2. REFER TO FLOOR PLANS FOR DEVICE LOCATIONS AND QUANTITIES. 3. EXISTING FIRE ALARM PANEL WORK SHALL INCLUDE ALL NEW CARDS AND EQUIPMENT NECESSARY TO SUPPORT THE NEW DEVICES AS INDICATED. 4. LABEL ALL FIRE ALARM DEVICES AS DIRECTED BY THE OWNER WITH EXTERNAL TAGS AND LABELS ON DEVICE BASES. TYPICAL SMOKE DETECTOR WITH SOUNDER BASE N.C. B151 M E B EXISTING NURSE CALL SYSTEM HEAD-END EQUIPMENT MASTER STATION TYPICAL DOME LIGHT EMERGENCY CALL STATION WITH PULL CORD AND RESET BUTTON. NOTES: 1.SUPPORTS FOR CABLE SHALL BE INDEPENDENTLY SUPPORTED. CABLE SHALL NOT LAY OVER CONDUIT, DUCTWORK, PIPING, STRUCTURAL SUPPORT MEMBERS, ETC. CABLE SHALL BE NEATLY INSTALLED PARALLEL AND AT RIGHT ANGLES TO THE BUILDING LINES. ENGINEER WILL REQUIRE CABLE TO BE REMOVED AND REINSTALLED IF IT IS NOT INSTALLED IN AN ACCEPTABLE MANNER. 2.REFER TO FLOOR PLANS FOR DEVICE LOCATIONS AND QUANTITY. 3.PROVIDE ALL REQUIRED EQUIPMENT AND MODIFICATIONS REQUIRED FOR A COMPLETE SYSTEM PER NEW DEVICE QUANTITIES AND LOCATIONS. 3.WIRING INSTALLATION: A.WIRING INSTALLED ABOVE ACCESSIBLE CEILINGS MAY BE EXPOSED CABLE. B. WIRING INSTALLED IN WALLS, ABOVE INACCESSIBLE CEILINGS, OR AREAS WITH EXPOSED CEILINGS SHALL BE INSTALLED IN CONDUIT COMPLETE. B P TYPICAL DOME LIGHT TYPICAL PATIENT STATION N CB TYPICAL NURSE ASSIST WITH CODE BLUE D TYPICAL DUTY STATION N.C. B151 FIRST FLOOR GENERATOR TO NEUTRAL BUS ON EMERGNECY PANEL GENERATOR TRANSFER DEVICE AC BALLAST OR LED DRIVER TO NEUTRAL BUS ON NORMAL PANEL TRANSFER SWITCH EMERGENCY POWER PANEL NORMAL POWER PANEL WALL SWITCH OR RELAY VOLTAGE SENSORNOTES: 1. NORMAL OPERATION - AC LIGHTING BALLAST OR LED DRIVER SUPPLIED BY NORMAL POWER PANEL AND CONTROLLED BY ROOM LIGHT SWITCH OR OCCUPANCY SENSOR. 2. EMERGENCY OPERATION - AC LIGHTING BALLAST OR LED DRIVER SUPPLIED BY GENERATOR THROUGH EMERGENCY POWER PANEL INDEPENDANT OF WALL SWITCH. 3. SEE MANUFACTURER'S WIRING INSTRUCTIONS FOR PROPER FIELD WIRING INSTRUCTIONS. FACE PLATE CONFIGURATION DATA ONLY (1) 1-1/4" EMT CONDUIT WITH NYLON BUSHING STUBBED TO ACCESSIBLE CEILING 4-11/16" x 4-11/16" SQUARE BOX 2-7/8" DEEP 5-8 DATA OUTLETS 4-11/16" x 4-11/16" SQUARE BOX 2-7/8" DEEP 2-GANG TILE RING 1/2" DEEP (2) 1-1/4" EMT CONDUITS WITH NYLON BUSHING STUBBED TO ACCESSIBLE CEILING 1-4 DATA OUTLETS 1/2" DEEP TILE RING CADDY SCREW GUN BRACKET NOTE: FOR METAL STUD WALL CONSTRUCTION ONLY. 4" SQUARE BOX METAL STUDS CONDUIT BOX MOUNTING BRACKET REFER TO DETAIL ON THIS SHEET FOR ADDITIONAL INFORMATION. LOCATED AS SHOWN ON DRAWINGS. CAT 5E CABLE 1" CONDUIT TO CABLE TRAY. TERMINATE CONDUITS WITH BUSHING. (TYPICAL) FIRST FLOOR NOTES: 1.SUPPORTS FOR CABLE SHALL BE INDEPENDENTLY SUPPORTED. CABLE SHALL NOT LAY OVER CONDUIT, DUCTWORK, PIPING,STRUCTURAL SUPPORT MEMBERS, ETC. CABLE SHALL BE NEATLY INSTALLED AT RIGHT ANGLES TO THE BUILDING LINES. ENGINEER WILL REQUIRE CABLE TO BE REMOVED AND REINSTALLED IF IT IS NOT INSTALLED IN AN ACCEPTABLE MANNER. 2.REFER TO FLOOR PLANS FOR DEVICE LOCATIONS AND QUANTITY 3.PROVIDE PLENUM RATED WIRE / CABLE AS REQUIRED. 4.PROVIDE ALL REQUIRED EQUIPMENT AND MODIFICATIONS REQUIRED FOR A COMPLETE SYSTEM PER NEW DEVICE QUANTITIES AND LOCATIONS EXISTING DATA RACK DATA B150 NUMBER INDICATES QUANTITY OF CABLES TO BE INSTALLED 2 EXISTING CABLE TRAY TELECOMMUNICATIONS CABLE TO BE TERMINATED AT IDF BY CONTRACTOR. TELECOM EQUIPMENT PROVIDED BY OWNER AS REQUIRED. 1 WAP S EXISTING AUDIO PAGING RACK TYPICAL GENERAL PAGE SPEAKER NOTES: 1.SUPPORTS FOR CABLE SHALL BE INDEPENDENTLY SUPPORTED. CABLE SHALL NOT LAY OVER CONDUIT, DUCTWORK, PIPING, STRUCTURAL SUPPORT MEMBERS, ETC. CABLE SHALL BE NEATLY INSTALLED PARALLEL AND AT RIGHT ANGLES TO THE BUILDING LINES. ENGINEER WILL REQUIRE CABLE TO BE REMOVED AND REINSTALLED IF IT IS NOT INSTALLED IN AN ACCEPTABLE MANNER. 2.REFER TO FLOOR PLANS FOR DEVICE LOCATIONS AND QUANTITY. 3.PROVIDE ALL REQUIRED EQUIPMENT AND MODIFICATIONS REQUIRED FOR A COMPLETE SYSTEM PER NEW DEVICE QUANTITIES AND LOCATIONS. 4.WIRING INSTALLATION: A.WIRING INSTALLED ABOVE ACCESSIBLE CEILINGS MAY BE EXPOSED CABLE. B. WIRING INSTALLED IN WALLS, ABOVE INACCESSIBLE CEILINGS, OR AREAS WITH EXPOSED CEILINGS SHALL BE INSTALLED IN CONDUIT COMPLETE. DATA B151 THIRD FLOOR S S S S S S S TYPICAL EMERGENCY PAGE SPEAKER JUNCTION BOX (TYPICAL FOR ALL) Architecture | Engineering | Interior Design 1715 Magnavox Way Fort Wayne, IN 46804 260.432.9337 930 North Meridian Indianapolis, IN 46204 317.917.1190 www.msktd.com SHEET TITLE SHEET NUMBER SET DESCRIPTION PROJECT NO. DATE MSKTD & Associates IR Equipment Replacement1203 E St. Clair Street,Suite. B Indianapolis, Indiana 46202 Phone: 1.317.927.8307 www.genesis-engineering.com 12/1/2016 1:11:34 PMElectrical Details E700 11700 N. Meridian Street | Carmel, Indiana 46032North Hospital6658 06-01-16A Renovation ForNO SCALE12" AND SMALLER CONDUIT SUPPORT DETAIL NO SCALE22-1/2" AND LARGER CONDUIT SUPPORT DETAIL NO SCALE3LAY IN LIGHT FIXTURE DETAIL NO SCALE4ELECTRICAL EQUIPMENT I.D. LABELING DETAIL NO SCALE5ELECTRICAL EQUIPMENT WARNING LABEL DETAIL NO SCALE6FIRE ALARM SYSTEM SCHEMATIC NO SCALE7NURSE CALL DETAIL NO SCALE8TYPICAL SWITCHED LIGHT FIXTURE WITH AUTOMATIC GENERATOR TRANSFER DEVICE SCHEMATIC NO SCALE9FLUSH MOUNTED DATA OUTLET 1/8" = 1'-0"10 WALL BOX INSTALLATION DETAIL NO SCALE11TELECOM SYSTEM DETAIL NO SCALE12AUDIO PAGING DETAIL REV. DATE