The URL can be used to link to this page

Home My WebLink About001 - A000 - Cover SheetSheet Number Sheet Name A000 Cover Sheet A001 General Information and Standard Details A002 2009 ICC/ANSI A117.1 A003 2009 ICC/ANSI A117.1 Restrooms & Parking A011 Code Information A021 Project Standards A211 Construction Floor Plan A221 Reflected Ceiling Plan A231 Electrical Location & Equipment Plan A241 Finish Plan and Notes A270 Enlarged Floor Plans A501 Interior Elevations A551 Interior Sections and Details A600 Door Notes, Elevations, and Details A601 Door Schedule E000 Electrical Notes, Symbols & Schedule E101 Lighting Plan E201 Power & Systems Plan E500 Panel Schedules P-410 04 Plumbing P-420 04 HVAC Piping P-421 Roof Layout Schedule SM-01 Building / Area Duct Plan TRUE SHEET NUMBER: COPYRIGHT 2017 CARSON DESIGN JOB NO. DATE: DRAWING TITLE: STAMP: Drawing List Area Map MEP Requirements Key Plan Carson Design Associates 9229 Delegates Row Suite 250 Indianapolis, IN 46240 Architecture / Design Contact MIDWEST SOUTHWEST 12301 Research Blvd Bldg IV - Suite 130 Austin, TX 78759 Tel 512.977.0520 Fax 512.977.0384 www.carsondesign.com 9229 Delegates Row Suite 250 Indianapolis, IN 46240 Tel 317.843.5979 Fax 317.843.5975 ISSUE: Project Description 01.31.18 I1720009 A000 I1720009 01.31.18 Cover Sheet 211 W. Main St., Carmel, IN 46032 211 W. Main St., Carmel, IN 46032 Invesque, Inc. Monon & Main Suite 400 Monon & Main Suite 400 Invesque, Inc. Matt Dziadosz Phone: 317.567.0234 mdziadosz@leach-russellmech.com Leach & Russell Mechanical 9151 Ford Circle Fishers, IN 46038 Julie Berry Phone: 317.843.3760 jberry@carsondesign.com Mech. & Plumbing Engineer Contact Drew Pojar Phone: 317.780.2923 dpojar@ermco.com Ermco 1625 W. Thompson Rd. (46217) P.O. Box 1507 Indianapolis, IN 46206 Electrical Engineer Contact Construction Documents - Addendum No.1 01.31.18 This project consists of the build out of a suite in a newly constructed building. This is a Design Build project, MEP drawings to follow. Project Location Area of Work PLAN TRUE 1. Refer to attached M, E, & P drawings for more information. If drawings are not included and scope requires M, P, or E work Contractor shall provide design build- design and permitting services for the scope required for a successful project. 2. The design and installation of all MEP systems shall comply with the current Codes in force by the AHJ at the project location. Any required energy compliance or environmental reports required by the AHJ shall be prepared by the Contractor if not provided by the Owner or Architect’s consultants. 3. Contractor to field verify all existing building conditions and systems affected by the project work and be familiar with the drawings and project requirements prior to bid or contracting with Owner. No structural cutting, coring, or drilling shall be performed that impacts any part of the existing facility, without prior approval. Contractor shall retain the services of a structural engineer, if required by the Architect, Owner, or AHJ to obtain a required approval. 4. Architectural drawing have been provided to show the locations of all devices and systems. Contractor shall be responsible for reconfigurations, modifications, and/or new work needed to provide a complete functioning job without permanently disrupting existing building systems. Contractor shall coordinate with Owner, Building Facilities, and or other Tenants 48 hours minimum in advance of any interruption of any building service. 5. Architectural drawings shall take precedence over all other trades drawings when conflicts arise. Contractor to bring conflicts or inconsistencies between the architectural drawings and the drawing of other trades to the attention of the architect prior to bid, order, or installation. 6. Fire sprinkler modifications and new work shall be designed by a licensed fire sprinkler system designer in the state the project resides in, and must be installed by a state licensed installer. Contractor shall obtain any required approvals from the AHJ prior to start of construction. 7. Zoning of MEP systems shall be exclusive to the project area without cross over to other building areas, except as is indicated on the documents or as approved in advance. 8. Contractor to provide all required test and balance reports, O&M manuals, and commissioning activities required by the AHJ or project requirements in the appropriate phases of the project. Note: E.C. and/or design build contractor is to verify that project meets Indiana ASHRAE 90.1 energy codes. Design intent is to be within watts per square foot. Provide energy managment controls, such as sensor controls (ultrasonic and motion detection) and/or relay time clocks, as required by the code. Indiana required energy compliance report (ComCheck) is the responsibility of the owner or owner's representative. Drawings, specifications and energy control devices are shown with the intent of meeting current state energy codes. Submitting party is to alert designer and owner of any additional devices or load changes necessary to adhere to the code prior to submission of ComCheck. Addendum No.1 02/26/18 Nick Mishler