HomeMy WebLinkAbout12GOOF PENETRATION
)7 92 OO.0
)7 62 00.8
)7 54 23.A
)7 54 23.B
NU I t: )5 31 OO.A
PROVIDE CRICKETS AS REQUIRED
AT ALL ROOF MOUNTED ITEMS AND
OTHER MISCELLANEOUS PENTRATIONS.
TYP ROOF
PENETRATION
SCALE: NTS
ROOF HATCH
SECTION DETAIL
SCALE: 1" = 1'-0"
07 72 OO.A
06 10 OO.A
07 54 23.A
07 54 23.8
05 31 OO.A
05 12 OO.A
ROOF PLAN
�01
SCALE: 1/8" = 1'-0"UU
NORTH
11
GENERAL NOTES:
A. ALL DIMENSIONS ARE FROM FACE OF STUD, OR FACE C.M.U. ANY
DIMENSIONS NOT SHOWN OR DEEMED QUESTIONABLE ARE TO VERIFIED
BY ARCHITECT/DESIGNER. CONTRACTOR SHALL VERIFY ALL DIMENSIONS
PRIOR TO FABRICATION AND INSTALLATION. DO NOT SCALE DRAWINGS.
B. PROVIDE WOOD BLOCKING SUPPORTS AS REQUIRED FOR ALL SURFACE
MOUNTED ITEMS.
C. COORDINATE WORK OF THIS TRADE WITH OTHER TRADES.
D. DOOR AND FRAME NUMBERS CORRESPOND TO ROOM NUMBERS. WHERE
MORE THAN ONE DOOR OCCURS IN A ROOM, A SUFFIX HAS BEEN ADDED
(I.E. 100A). SEE DIVISION 500 DRAWINGS FOR DOOR SCHEDULE.
E. PROVIDE MISCELLANEOUS METAL SUPPORT FOR ALL CEILING
SUSPENDED ITEMS.
F. APPLY SEALANT AT ALL JUNCTURES BETWEEN DIFFERENT MATERIALS (I.E.
STOREFRONT AND PRECAST).
G. APPLY SEALANT AT ALL PLUMBING FIXTURES AT JUNCTURE WITH WALL.
H. APPLY SEALANT AT ALL COUNTERTOPS AND BACK SPLASHES AT JUNCTURE
WITH WALL.
I. ALL STEEL STUDS ARE TO BE BRACED ACCORDING TO MANUFACTURER'S
LIMITING HEIGHT L/240.
J. NOT USED.
K. ALL INTERIOR WALLS SHALL BE MARKED IN PLACE PRIOR TO FRAMING
FOR ARCHITECT/DESIGNER TO REVIEW.
L. ALL DOORS MUST BE INSTALLED WITH AT LEAST THE MINIMUM
MANEUVERING CLEARANCE AT THE DOOR APPROACH PER THE MOST
CURRENT AMERICANS WITH DISABILITIES ACT.
M. NOT USED
N. UNDERSIDE OF ALL SHAFTS TO RECEIVE 1-1/2 HOUR SHAFTWALL
HUNG HORIZONTAL IN OPENING IN LOWEST FLOOR PENETRATED
PLAN NOTES
O ALIGN FINISH FACES.
0 STANDARD ROOF DRAIN AND OVERFLOW DRAIN. SEE DETAIL 4/A203.
O EDGE OF CANOPY.
O4 ROOF HATCH. SEE STRUCTURAL DRAWINGS FOR EXACT LOCATION. SEE DETAIL
2/A203.
O5 ROOF TOP MECHANICAL UNIT OR EXHAUST FAN LOCATION ON CURB. SEE
MECHANICAL DRAWINGS FOR ADDITIONAL INFORMATION.
sA 8" WIDE x 6" DEEP DOWNSPOUT
68 4" WIDE x 4" DEEP DOWNSPOUT
O MINIMUM EQUIPMENT CLEARANCES.
O ROOF PENETRATION. SEE DETAIL 3/A203. SEE MEP DRAWINGS FOR
ADDITIONAL INFORMATION.
O9 VERTICAL STEEL LADDER. SEE SPECIFICATION SECTION 05 50 00.
10 ROOF HATCH UNIT. SEE SPECIFICATION SECTION 07 72 00.
11 ROOF CRICKET
12 DRIVE -UP WINDOW SYSTEM BY TENANT. VERIFY SIZE AND CONFIGURATION.
13 RECESSED FLOOR SLAB. COORDINATE WITH EQUIPMENT REQUIREMENTS. SEE
STRUCTURAL.
14 MECHANICALLY ATTACHED MEMBRANE ROOF SYSTEM.
15 SCUPPER AND CONDUCTOR HEAD. DESIGN AND INSTALL IN ACCORDANCE WITH
SMACNA STANDARDS AND APPLICABLE CODES.
KEYNOTES
DIVISION 5 — METALS
05 12 ODA
STRUCTURAL STEEL FRAMING MEMBER. REF. STRUCTURAL DRAWINGS.
05 31 ODA
STEEL DECKING. REFERENCE STRUCTURAL DRAWINGS.
DIVISION 6 — WOOD, PLASTICS AND COMPOSITES
06 10 OOA
FIRE AND PRESERVATIVE TREATED WOOD BLOCKING/NAILER.
DIVISION 7 — THERMAL AND MOISTURE PROTECTION
07 54 23A
MECHANICALLY ATTACHED WHITE TPO ROOF MEMBRANE SYST.EM
07 54 23.B
R-19 POLYISOCYANURATE ROOF INSULATION
07 72 00A
ROOF HATCH.
07 92 OO.0
WATER CUT OFF MASTIC.
Scope Drawings:
These drawings indicate the general scope of the project
in terms of architectural design concept, the dimensions of
the building, the major architectural elements and the type
of structural, mechanical and eIectrica'. systems.
The drawings do not necessarily ird cote or describe all
work required for full performance and completion of the
requirements of the Contract.
On the basis of the general scope indicated or described,
the trade contractors shall furnish alp items required for the
proper execution and completion of the work.
Revisions:
L
N
07/06/12
AMI JBA
Z
u
C
�--�ton
z
Ell
V
w
"
A
� in
a;
0 in
a
all
C
17-
U
V
z
_
C8 c
•
M
PbA }{
�+
o
a
C3
( w
Lu
2
(00
O
U
U
N
`
W
ti
06
Q
Ell
_
x
�00
(0
J
x
M
00
o
U
00
�
o
t
O
Scope Drawings:
These drawings indicate the general scope of the project
in terms of architectural design concept, the dimensions of
the building, the major architectural elements and the type
of structural, mechanical and eIectrica'. systems.
The drawings do not necessarily ird cote or describe all
work required for full performance and completion of the
requirements of the Contract.
On the basis of the general scope indicated or described,
the trade contractors shall furnish alp items required for the
proper execution and completion of the work.
Revisions:
L
Checked By
07/06/12
AMI JBA
JER000go
4)
Ell
.v
all
C
O
_
♦+
Im
'a
C
Lu
2
Cc
O
_a
O
a
`
W
Ell
(0
m
t
r
Scope Drawings:
These drawings indicate the general scope of the project
in terms of architectural design concept, the dimensions of
the building, the major architectural elements and the type
of structural, mechanical and eIectrica'. systems.
The drawings do not necessarily ird cote or describe all
work required for full performance and completion of the
requirements of the Contract.
On the basis of the general scope indicated or described,
the trade contractors shall furnish alp items required for the
proper execution and completion of the work.
Revisions:
Issue Date
Certified By:
�,�xunuuuse,
No.
= AR00910036
STATE OF
44
Drawn By
Checked By
07/06/12
AMI JBA
JER000go
Issue
Issue Date
Certified By:
�,�xunuuuse,
No.
= AR00910036
STATE OF
44
Drawn By
Checked By
07/06/12
AMI JBA
JER000go
Drawing Number:
Project Number.
11140
4