HomeMy WebLinkAbout10 28 00 Toilet and Bath AccessoriesTHE KENT
10 28 00-
THE KENT Issue Date 05.09.18 TOILET AND BATH ACCESSORIES
THE KENT
SECTION 10 28 00 – TOILET AND BATH ACCESSORIES
PART 1 - GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary
Conditions and Division 01 Specification Sections, apply to this Section.
1.2 SUMMARY
A. Section Includes:
1. Public-use washroom/shower room accessories.
2. Childcare accessories.
3. Under-lavatory guards.
B. Related Requirements:
1. Section 08 83 00 "Mirrors" for frameless mirrors.
2. Section 09 30 00 “Tiling" for ceramic toilet and bath accessories.
3. Section 10 28 10 "Janitor’s Closet Accessories" for janitorial accessories.
1.3 COORDINATION
A. Coordinate accessory locations with other work to prevent interference with clearances required
for access by people with disabilities, and for proper installation, adjustment, operation,
cleaning, and servicing of accessories.
B. Deliver inserts and anchoring devices set into concrete or masonry as required to prevent
delaying the Work.
1.4 ACTION SUBMITTALS
A. Product Data: For each type of product.
1. Include construction details, material descriptions, dimensions of individual components
and profiles, and finishes.
2. Include anchoring and mounting requirements, including requirements for cutouts in other
work and substrate preparation.
3. Include electrical characteristics.
B. Samples: Full size, for each exposed product and for each finish specified.
1. Approved full-size Samples will be returned and may be used in the Work.
C. Product Schedule: Indicating types, quantities, sizes, and installation locations by room of each
accessory required.
1. Identify locations using room designations indicated.
2. Identify accessories using designations indicated.
THE KENT
10 28 00-
THE KENT Issue Date 05.09.18 TOILET AND BATH ACCESSORIES
THE KENT
1.5 INFORMATIONAL SUBMITTALS
A. Sample Warranty: For manufacturer's special warranty.
1.6 CLOSEOUT SUBMITTALS
A. Maintenance Data: For accessories to include in maintenance manuals.
1.7 WARRANTY
A. Manufacturer's Special Warranty for Mirrors: Manufacturer agrees to repair or replace mirrors
that fail in materials or workmanship within specified warranty period.
1. Failures include, but are not limited to, visible silver spoilage defects.
2. Warranty Period: 15 years from date of Substantial Completion.
PART 2 - PRODUCTS
2.1 PERFORMANCE REQUIREMENTS
A. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, by
a qualified testing agency, and marked for intended location and application.
2.2 PUBLIC-USE WASHROOM/SHOWER ROOM ACCESSORIES
A. Source Limitations: Obtain public-use washroom accessories from single source from single
manufacturer.
B. Toilet Tissue (Roll) Dispenser: T6
1. Bobrick B-4288.
2. Description: Roll-in-reserve dispenser with hinged front secured with tumbler lockset
Single-roll dispenser.
3. Mounting: Surface mounted.
4. Operation: Non-control delivery with standard spindle.
5. Capacity: Designed for up to 5-inch- diameter tissue rolls.
6. Material and Finish: Stainless steel, No. 4 finish (satin).
C. Combination Towel (Folded) Dispenser/Waste Receptacle: T8
1. Bobrick B-43944.
2. Description: Combination unit for dispensing C-fold or multifold towels, with removable
waste receptacle.
3. Mounting: Recessed with projecting receptacle.
a. Designed for nominal 4-inch wall depth.
4. Minimum Towel-Dispenser Capacity: 600 C-fold or 800 multifold paper towels.
5. Minimum Waste-Receptacle Capacity: 15 gal.
6. Material and Finish: Stainless steel, No. 4 finish (satin).
7. Liner: Reusable, vinyl waste-receptacle liner.
8. Lockset: Tumbler type for towel-dispenser compartment.
THE KENT
10 28 00-
THE KENT Issue Date 05.09.18 TOILET AND BATH ACCESSORIES
THE KENT
D. Combination Towel (Folded) Dispenser/Waste Receptacle: T8A
1. Bobrick B-4369.
2. Description: Combination unit for dispensing C-fold or multifold towels, with removable
waste receptacle.
3. Mounting: Recessed with projecting receptacle.
a. Designed for nominal 4-inch wall depth.
4. Minimum Towel-Dispenser Capacity: 350 C-fold or 475 multifold paper towels.
5. Minimum Waste-Receptacle Capacity: 3 gal.
6. Material and Finish: Stainless steel, No. 4 finish (satin).
7. Liner: Reusable, vinyl waste-receptacle liner.
8. Lockset: Tumbler type for towel-dispenser compartment.
E. Liquid-Soap Dispenser: T4.
1. Bobrick B-2111.
2. Description: Designed for dispensing soap in liquid or lotion form.
3. Mounting: Vertically oriented, surface mounted.
4. Capacity: 40 fl. oz.
5. Material and Finish: Stainless steel, No. 4 finish (satin).
6. Lockset: Tumbler type.
7. Refill Indicator: Window type.
F. Liquid-Soap Dispenser: T4A.
1. Bobrick B-8221.
2. Description: Designed for dispensing soap in liquid or lotion form.
3. Mounting: Horizontally oriented, recessed.
4. Capacity: 20 fl. oz.
5. Materials: High impact resistant ABS plastic with a shatter proof polyethylene container.
6. Lockset: Vandal resistant locking cover.
G. Grab Bar: T1.
1. Bobrick B-6806 x 18.
2. Mounting: Flanges with concealed fasteners.
3. Material: Stainless steel, 0.05 inch thick.
a. Finish: Smooth, No. 4 finish (satin).
4. Outside Diameter: 1-1/2 inches.
5. Configuration and Length: Straight, 18 inches long.
H. Grab Bar: T2.
1. Bobrick B-6806 x 36.
2. Mounting: Flanges with concealed fasteners.
3. Material: Stainless steel, 0.05 inch thick.
a. Finish: Smooth, No. 4 finish (satin).
4. Outside Diameter: 1-1/2 inches.
5. Configuration and Length: Straight, 36 inches long.
I. Grab Bar: T3.
1. Bobrick B-6806 x 48.
2. Mounting: Flanges with concealed fasteners.
3. Material: Stainless steel, 0.05 inch thick.
a. Finish: Smooth, No. 4 finish (satin).
4. Outside Diameter: 1-1/2 inches.
5. Configuration and Length: Straight, 36 inches long.
THE KENT
10 28 00-
THE KENT Issue Date 05.09.18 TOILET AND BATH ACCESSORIES
THE KENT
J. Sanitary-Napkin Disposal Unit: T9.
1. Bobrick B-270.
2. Mounting: Surface mounted.
3. Door or Cover: Self-closing, disposal-opening cover.
4. Receptacle: Removable.
5. Material and Finish: Stainless steel, No. 4 finish (satin).
K. Mirror Unit: T7A.
1. Bobrick B2908 36 x 60.
2. Frame: Stainless-steel angle, 0.05 inch thick.
a. Corners: Manufacturer's standard.
3. Hangers: Produce rigid, tamper- and theft-resistant installation, using method indicated
below.
a. Wall bracket of galvanized steel, equipped with concealed locking devices
requiring a special tool to remove.
4. Size: 36 inches x 60 inches.
L. Mirror Unit: T7B.
1. Bobrick B290 24 x 36.
2. Frame: Stainless-steel angle, 0.05 inch thick.
a. Corners: Manufacturer's standard.
3. Hangers: Produce rigid, tamper- and theft-resistant installation, using method indicated
below.
a. Wall bracket of galvanized steel, equipped with concealed locking devices
requiring a special tool to remove.
4. Size: 24 inches x 36 inches.
M. Mirror Unit: T7.
1. Electric Mirror INT-54x42-L7CS-30K
2. Frame: Stainless-steel.
a. Corners: Manufacturer's standard.
3. Hangers: Produce rigid, tamper- and theft-resistant installation, using method indicated
below.
a. Wall bracket of galvanized steel, equipped with concealed locking devices
requiring a special tool to remove.
4. Size: 54 inches W x 42 inches H.
5. Internally lit at edge.
N. Shower Curtain Rod: T10.
1. Bobrick B-207 x 36
2. Description: 1-inch OD; fabricated from nominal 0.0375-inch- thick stainless steel.
3. Mounting Flanges: Concealed wall brackets with 1-3/8 inch OD chrome plated plastic
flange.
4. Finish: Stainless steel, No. 4 finish (satin).
O. Towel Pin: T12.
1. Bobrick B-677.
2. Description: Single-prong unit.
3. Material and Finish: Stainless steel, No. 7 finish (polished).
P. Utility Hook: T11.
1. Bobrick B-670.
2. Description: Single-prong unit.
THE KENT
10 28 00-
THE KENT Issue Date 05.09.18 TOILET AND BATH ACCESSORIES
THE KENT
3. Material and Finish: Stainless steel, No. 7 finish (polished).
2.3 CHILDCARE ACCESSORIES
A. Diaper-Changing Station: T5.
1. Bobrick KB200-01SS.
2. Description: Horizontal unit that opens by folding down from stored position and with
child-protection strap.
a. Engineered to support minimum of 250-lb static load when opened.
3. Mounting: Surface mounted, with unit projecting not more than 4 inches from wall when
closed.
4. Operation: By pneumatic shock-absorbing mechanism.
5. Material and Finish: Stainless steel, No. 4 finish (satin), exterior shell with rounded
plastic corners; HDPE interior in manufacturer's standard color.
6. Liner Dispenser: Built in.
2.4 UNDER-LAVATORY GUARDS
A. Under-lavatory Guard:
1. Refer to Drawings for under lavatory protection panels.
2. Insulating Pipe Coverings: Insulating pipe covering for supply and drain piping
assemblies that prevents direct contact with and burns from piping; allow service access
without removing coverings.
3. Material and Finish: Antimicrobial, molded plastic, white.
2.5 CUSTODIAL ACCESSORIES
A. Refer to Specification Section 10 28 10 “Janitor’s Closet Accessories.
2.6 MATERIALS
A. Stainless Steel: ASTM A 666, Type 304, 0.031-inch minimum nominal thickness unless
otherwise indicated.
B. Brass: ASTM B 19, flat products; ASTM B 16, rods, shapes, forgings, and flat products with
finished edges; or ASTM B 30, castings.
C. Steel Sheet: ASTM A 1008, Designation CS (cold rolled, commercial steel), 0.036-inch minimum
nominal thickness.
D. Galvanized-Steel Sheet: ASTM A 653, with G60 hot-dip zinc coating.
E. Galvanized-Steel Mounting Devices: ASTM A 153, hot-dip galvanized after fabrication.
F. Fasteners: Screws, bolts, and other devices of same material as accessory unit and tamper-
and-theft resistant where exposed, and of galvanized steel where concealed.
G. Chrome Plating: ASTM B 456, Service Condition Number SC 2 (moderate service).
THE KENT
10 28 00-
THE KENT Issue Date 05.09.18 TOILET AND BATH ACCESSORIES
THE KENT
H. Mirrors: ASTM C 1503, Mirror Glazing Quality, clear-glass mirrors, nominal 6.0 mm thick.
2.7 FABRICATION
A. General: Fabricate units with tight seams and joints, and exposed edges rolled. Hang doors and
access panels with full-length, continuous hinges. Equip units for concealed anchorage and with
corrosion-resistant backing plates.
B. Keys: Provide universal keys for internal access to accessories for servicing and resupplying.
Provide minimum of six keys to Owner's representative.
PART 3 - EXECUTION
3.1 INSTALLATION
A. Install accessories according to manufacturers' written instructions, using fasteners appropriate
to substrate indicated and recommended by unit manufacturer. Install units level, plumb, and
firmly anchored in locations and at heights indicated.
B. Grab Bars: Install to withstand a downward load of at least 250 lbf, when tested according to
ASTM F 446.
3.2 ADJUSTING AND CLEANING
A. Adjust accessories for unencumbered, smooth operation. Replace damaged or defective items.
B. Remove temporary labels and protective coatings.
C. Clean and polish exposed surfaces according to manufacturer's written instructions.
END OF SECTION 10 28 00