HomeMy WebLinkAbout224000 PLUMBING FIXTURESTHE KENT
22 40 00 - 1
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
SECTION 22 40 00 - PLUMBING FIXTURES
PART 1 - GENERAL
1.01 RELATED SECTIONS:
A. Drawings, general provisions of the Contract, including General and Supplementary
Conditions, and Division-1 Specification Sections and Division 20 Specification Sections, apply
to work of this Section.
B. Separate grab bar and toilet accessories are not an integral part of plumbing fixtures and are
specified in Division 10.
1.02 DESCRIPTION OF WORK:
A. Extent of plumbing fixtures work required by this Section is indicated on drawings and
schedules, and by requirements of this Section.
B. Types of plumbing fixtures specified in this Section include the following:
1. Water Closets
2. Urinals
3. Lavatories
4. Sinks
5. Food Waste Disposers
6. Mop Basins
7. Showers
8. Bath Tubs
9. Clothes Washer Boxes
10. Shut-Off Valve Boxes
11. Washing Machine Drain Pans
C. Refer to Division 26 Sections for field-installed electrical wiring required for water coolers, food
waste disposers and other plumbing fixtures; not work of this Section.
1.03 QUALITY ASSURANCE:
A. Plumbing Fixture Standards: Comply with applicable portions of the Indiana Plumbing Code
herein referred to as the Plumbing Code.
B. ANSI Standards: Comply with applicable ANSI standards pertaining to plumbing fixtures and
systems, and bath tub units including the following:
1. ANSI A112.6.1 – Supports for Off-the-Floor Plumbing Fixtures for Public Use.
2. ANSI A112.18.1 – Plumbing Fixture Fittings.
3. ANSI A112.19.1 – Enameled Cast Iron Plumbing Fixtures.
4. ANSI A112.19.2 – Vitreous China Plumbing Fixtures.
5. ANSI A112.19.3 – Stainless Steel Plumbing Fixtures (Designed for Residential Use).
THE KENT
22 40 00 - 2
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
C. PDI Compliance: Comply with standards established by PDI pertaining to plumbing fixture
supports.
D. NAHB Label: Provide fiberglass bath tub units and shower stalls which have been tested and
labeled by NAHB Research Foundation, Inc.
E. UL Compliance: Construct water coolers in accordance with UL Standard 399 "Drinking-Water
Coolers," and provide UL-listing and label.
F. ASHRAE Compliance: Test and rate water coolers in accordance with ASHRAE Standard 18
"Method of Testing for Rating Drinking Water Coolers with Self-Contained Mechanical
Refrigeration Systems."
G. ARI Compliance: Construct and install water coolers in accordance with ARI Standard 1010
"Drinking-Fountains and Self-Contained Mechanically- Refrigerated Drinking-Water Coolers,"
and provide Certification Symbol.
H. ANSI Compliance: Construct and install barrier-free plumbing fixtures in accordance with ANSI
Standard A117.1 "Specifications for making buildings and facilities accessible to and usable by
physically handicapped people."
I. ASSE Compliance: ASSE 1037 – Flushometers (Pressurized Flushing Devices)
J. ADA Compliance: Construct and install barrier-free plumbing fixtures in accordance with Title
III of the ADA of 1990 accessibility guidelines for buildings and facilities.
K. IBC Compliance: Construct and install barrier-free plumbing fixtures in accordance with IBC
Chapter 11 - Accessibility for Public Accommodations and Commercial Facilities, as adopted
and amended by the State of Indiana, latest enforced edition.
1.04 SUBMTTALS:
A. Product Data: Submit Manufacturer's Technical Product Data and installation instructions for
each fixture, faucet, specialty, accessory, and trim specified; clearly indicate rated capacities
of selected models.
B. Shop Drawings: Submit rough-in drawings. Detail dimensions, rough-in requirements, required
clearances, and methods of assembly of components and anchorages. Coordinate
requirements with Architectural Woodwork shop drawings for fixtures installed in countertops
and cabinets. Furnish templates for use in woodwork shop.
C. Maintenance Data: Submit maintenance data and parts lists for each type of plumbing fixture
and accessory; including "trouble-shooting" maintenance guide. Include this data and produce
data in maintenance manual; in accordance with requirements of Division-1.
1.05 DELIVERY, STORAGE, AND HANDLING:
A. Deliver plumbing fixtures, specialties, accessories, and trim individually wrapped in factory-
fabricated containers.
THE KENT
22 40 00 - 3
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
B. Handle plumbing fixtures specialties, accessories, and trim carefully to prevent breakage,
chipping and scoring fixture finish. Do not install damaged plumbing fixtures specialties,
accessories, or trim; replace and return damaged units to equipment manufacturer.
PART 2 - PRODUCTS
2.01 GENERAL:
A. General: Provide factory-fabricated fixtures of type, style and material indicated. For each type
fixture, provide trim and fittings including faucets, supplies, stops, traps, tailpieces, waste
nipples, hangers, plates, brackets, anchors, supports, hardware, and fastening devices
required for a complete installation.
B. All vitreous china plumbing fixtures shall be furnished by the same manufacturer for each
product specified throughout.
C. All fixture trim shall be by same manufacturer for each product specified throughout.
2.02 MATERIALS:
A. Provide materials which have been selected for their surface flatness and smoothness.
Exposed surfaces which exhibit pitting, seam marks, roller marks, foundry sand holes, stains,
discoloration, or other surface imperfections on finished units are not acceptable.
B. Where fixture trim and accessories are exposed or semi-exposed, provide bright chrome-
plated or polished stainless-steel units. Provide copper or brass where not exposed.
C. Stainless Steel: ASTM A 167, Type 302/304, hardest workable temper, with No. 4 finish
having, bright, directional polish on exposed surfaces.
D. Vitreous China: High Quality, free from fire cracks, spots, blisters, pinholes and specks; glaze
exposed surfaces, and test for crazing resistance in accordance with ASTM C 554.
E. Fiberglass: ANS1 Z124, smooth surfaced, with color selected by Architect/Engineer.
F. Synthetic Stone: High quality, free from defects, glaze on exposed surfaces, stain resistant.
2.03 WATER CLOSETS (TANK TYPE):
A. Water Closet (WC-1): 1.6 GPF, white vitreous china, floor outlet, siphon jet elongated bowl
with close-coupled tank and seat.
1. Fixture: PROFLO, PF1201WH/PF3312WH.
2. 1/2" I.P.S. x 3/8" O.D. wheel handle angle stop wall supply with closet riser.
3. Float valve with vacuum breaker.
4. Right-hand or Left-hand flush valve with chrome plated trip lever.
5. Seat: Kohler K-4647 Stonewood elongated closed white seat, with cover.
B. Water Closet (WC-2): ADA compliant, 1.6 GPF, white vitreous china, floor outlet, siphon jet,
elongated bowl with close-coupled tank and seat.
1. Fixture: PROFLO, PF1203WH/PF3312WH.
THE KENT
22 40 00 - 4
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
2. 1/2" I.P.S. x 3/8" O.D. wheel handle angle stop wall supply with closet riser.
3. Float valve with vacuum breaker.
4. Right-hand or Left-hand flush valve with chrome plated trip lever.
5. Seat: Kohler K-4647 Stonewood elongated closed white seat, with cover.
2.04 WATER CLOSETS (FLOOR OUTLET FLUSH VALVE):
A. Water Closet (WC-3): 1.28 GPF, 15” to rim, white vitreous china, floor outlet, siphon jet,
elongated bowl with top spud.
1. Mansfield, Baltic 1311NS.
a. MaP rating; 1000 grams.
2. ASSE 1037- Flushometer Valve;
a. Exposed, quiet-operating, chrome plated flushometer valve. Valve shall be
non-hold-open with no external volume adjustment, chloramine resistant,
vacuum breaker with bottom hex coupling nut, screwdriver stop with (free
spinning), vandal resistant stop cap and sweat solder adapter kit with cast set
screw wall flange.
(1) Moen, 8310M128.
(2) Delta, 81T201.
b. Alternate: - exposed, battery powered sensor operated quiet-operating
chrome plated flushometer valve and infrared sensor housing. Valve shall be
non-hold-open integral solenoid operator, courtesy flush override button,
infrared sensor with indicator light, three second flush delay, chloramine
resistant, vacuum breaker with bottom hex coupling nut, screwdriver stop with
(free spinning), including four (4) size AA batteries, vandal resistant stop cap
and sweat solder adapter kit with cast set screw wall flange. (24-hour sentinel
flush).
(1) Moen, 8311 – WaterSense.
(2) Delta, 81T201BTA.
3. Seat: Church Commercial, 3155CT white solid plastic, open front, integral check seat,
less cover.
B. Water Closet (WC-4): ADA compliant, 1.28 GPF, 17” to rim, white vitreous china, floor outlet,
siphon jet, elongated bowl with top spud.
1. Mansfield, Adriatic 1319.
a. MaP rating; 1000 grams.
2. ASSE 1037- Flushometer Valve;
a. Exposed, quiet-operating, chrome plated flushometer valve. Valve shall be
non-hold-open with no external volume adjustment, chloramine resistant,
vacuum breaker with bottom hex coupling nut, screwdriver stop with (free
spinning), vandal resistant stop cap and sweat solder adapter kit with cast set
screw wall flange.
(1) Moen, 8310M128.
(2) Delta, 81T201.
THE KENT
22 40 00 - 5
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
b. Alternate: - exposed, battery powered sensor operated quiet-operating
chrome plated flushometer valve and infrared sensor housing. Valve shall be
non-hold-open integral solenoid operator, courtesy flush override button,
infrared sensor with indicator light, three second flush delay, chloramine
resistant, vacuum breaker with bottom hex coupling nut, screwdriver stop with
(free spinning), including four (4) size AA batteries, vandal resistant stop cap
and sweat solder adapter kit with cast set screw wall flange. (24-hour sentinel
flush).
(1) Moen, 8311 – WaterSense.
(2) Delta, 81T201BTA.
3. Seat: Church Commercial, 3155CT white solid plastic, open front, integral check seat,
less cover.
2.05 URINALS (WALL HUNG):
A. Urinal (UR-1): ADA compliant, 0.5 GPF, 17” to rim, white vitreous china, wall hung, siphon jet
urinal with extended shields, top spud, integral flush spreader and trap.
1. Fixture: Mansfield, 475HE.
2. ASSE 1037- Flushometer Valve;
a. Exposed, quiet-operating, chrome plated flushometer valve. Valve shall be
non-hold-open with no external volume adjustment, chloramine resistant,
vacuum breaker with bottom hex coupling nut, screwdriver stop with (free
spinning), vandal resistant stop cap and sweat solder adapter kit with cast set
screw wall flange.
(1) Moen, 8312M05.
(2) Delta, 81T231.
b. Alternate: - exposed, battery powered sensor operated quiet-operating
chrome plated flushometer valve and infrared sensor housing. Valve shall be
non-hold-open integral solenoid operator, courtesy flush override button,
infrared sensor with indicator light, three second flush delay, chloramine
resistant, vacuum breaker with bottom hex coupling nut, screwdriver stop with
(free spinning), including four (4) size AA batteries, vandal resistant stop cap
and sweat solder adapter kit with cast set screw wall flange. (24-hour sentinel
flush).
(1) Moen, 8315 – WaterSense.
(2) Delta, 81T231BTA.
3. J.R. Smith 636 floor mount support.
2.06 LAVATORIES:
A. Lavatory (L-1): 17 1/2" x 14 3/8" white oval vitreous china, under-mount, with overflow and
with faucet holes in countertop on 8" centers.
1. Fixture: PROFLO, PF1714U.
2. Faucet: PROFLO, PF1112MCP, chrome finish, lever handles, 2.0 GPM flow rate, with
chrome pop-up drain assembly.
3. Adjustable two-piece cast-brass P-trap with cleanout with escutcheon.
4. 1/2" I.P.S. x 3/8" O.D. loose key angle stop supplies with flexible risers and 1/2"
chrome plated nipples and escutcheons.
THE KENT
22 40 00 - 6
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
B. Lavatory (L-2): ADA compliant, 17 1/2" x 14 3/8" white oval vitreous china, under-mount, with
overflow and with faucet holes in countertop on 8" centers.
1. Fixture: PROFLO, PF1714U.
2. Faucet: PROFLO, PF1112MCP, chrome finish, lever handles, 2.0 GPM flow rate, with
chrome pop-up drain assembly.
3. Adjustable two-piece cast-brass P-trap with cleanout with escutcheon.
4. 1/2" I.P.S. x 3/8" O.D. loose key angle stop supplies with flexible risers and 1/2"
chrome plated nipples and escutcheons.
5. Install for barrier free use with insulated drain and water supplies.
C. Lavatory (L-3): ADA compliant, nominal 18" x 13" white rectangular vitreous china, under-
mount, with overflow.
1. Fixture:
a. Mansfield, Brentwood 234.
b. Kohler, Caxton K-20000-0.
2. Faucet: With faucet holes in countertop on 8" centers. Chrome finish, lever handles,
0.5 GPM flow control outlet, with chrome pop-up drain assembly.
a. Kohler, K-942-4-CP.
b. Moen, Gibson T6142, valve 9000.
c. Delta, Trinsic 3559.
d. Pfister, Contempra LG49-NC1C.
3. Alternate Faucet: With single faucet hole in countertop. Chrome finish, lever handles,
battery powered sensor operated vandal resistant 0.5 GPM flow control outlet, with
open grid strainer. Lead-Free ASSE 1070 thermostatic mixing valve.
a. Moen, 8559.
b. Delta, 631TP350.
4. Adjustable two-piece cast-brass P-trap with cleanout with escutcheon.
5. 1/2" I.P.S. x 3/8" O.D. loose key angle stop supplies with flexible risers and 1/2"
chrome plated nipples and escutcheons.
6. Install for barrier free use with insulated drain and water supplies.
D. Lavatory (L-4): ADA compliant, nominal 22" x 18" white vitreous china, with overflow, wall-
mount for concealed arm bracket, vitreous china shroud.
1. Fixture:
a. Kohler, Pinoir K-2035-8-0, with shroud. (With alternate faucet; Pinoir K-2035-
1-0, with shroud.)
b. Mansfield, Pamlico 2038-8, with shroud. (With alternate faucet; Pamlico 2038-
, with shroud.)
2. Faucet: With faucet holes in lavatory on 8" centers. Chrome finish, lever handles, 0.5
GPM flow control outlet, with chrome pop-up drain assembly.
a. Kohler, K-942-4-CP.
b. Moen, Gibson T6142, valve 9000.
c. Delta, Trinsic 3559.
d. Pfister, Contempra LG49-NC1C.
THE KENT
22 40 00 - 7
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
3. Alternate Faucet: With single faucet hole in lavatory. Chrome finish, lever handles,
battery powered sensor operated vandal resistant 0.5 GPM flow control outlet, with
open grid strainer. Lead-Free ASSE 1070 thermostatic mixing valve.
a. Moen, 8559.
b. Delta, 631TP350.
4. Adjustable two-piece cast-brass P-trap with cleanout with escutcheon.
5. 1/2" I.P.S. x 3/8" O.D. loose key angle stop supplies with flexible risers and 1/2"
chrome plated nipples and escutcheons.
6. Install for barrier free use with insulated drain and water supplies.
7. J.R. Smith 700 floor mount concealed arm support.
E. Lavatory (L-5): nominal 22" x 18" white vitreous china, with overflow, wall-mount for concealed
arm bracket, vitreous china shroud.
1. Fixture: With faucet holes in lavatory on 8" centers.
a. Kohler, Pinoir K-2035-8-0, with shroud.
b. Mansfield, Pamlico 2038-8, with shroud.
2. Faucet: PROFLO, PF1112MCP, chrome finish, lever handles, 2.0 GPM flow rate, with
chrome pop-up drain assembly.
3. Adjustable two-piece cast-brass P-trap with cleanout with escutcheon.
4. 1/2" I.P.S. x 3/8" O.D. loose key angle stop supplies with flexible risers and 1/2"
chrome plated nipples and escutcheons.
5. J.R. Smith 700 floor mount concealed arm support.
2.07 SINKS (STAINLESS STEEL)
A. Sink (SK-1): 31 5/8" x 20 1/2" O.D., double compartment, 18-gauge stainless steel, under
mount sink, center drains, with 8 1/2" deep bowl.
1. Fixture: PROFLO PFUO907 / PFUO907R.
a. Refer to Architectural Enlarged Unit Plans for specified right or left hand sink.
2. Faucet: Kohler Faucets, K-596 single handle lever, pull down faucet, 1.8 GPM flow
rate.
3. Standard duo strainer with tailpiece.
4. Adjustable two-piece chrome plated cast-brass P-trap with cleanout with escutcheon.
5. 1/2" I.P.S. x 3/8" O.D. loose key angle stop supplies with flexible risers and 1/2"
chrome plated nipples and escutcheons.
B. Sink (SK-2): ADA compliant, 31 3/4" x 18 1/2" O.D., double compartment, 18-gauge stainless
steel, under mount sink, rear drains, with 5.5" deep bowl.
1. Fixture: Elkay ELUHAD3118.
2. Faucet: Kohler Faucets, K-596 single handle lever, pull down faucet, 1.8 GPM flow
rate.
3. Standard duo strainer with tailpiece.
4. Adjustable two-piece chrome plated cast-brass P-trap with cleanout with escutcheon.
5. 1/2" I.P.S. x 3/8" O.D. loose key angle stop supplies with flexible risers and 1/2"
chrome plated nipples and escutcheons.
THE KENT
22 40 00 - 8
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
C. Sink (SK-3): ADA compliant, nominal 23” x 18” O.D., single compartment, 18-gauge stainless
steel, under mount sink, rear drain, with nominal 5.5" deep bowl.
1. Fixture:
a. Moen, G18192B.
b. Kohler, K-3894-4.
c. Elkay, ELUHAD191655.
2. Faucet: With single faucet hole in countertop, single handle lever, pull down faucet,
1.5 to 1.8 GPM flow rate.
a. Moen, Align 5923SRS
b. Kohler, Tournant K-77515-VS.
c. Delta, Trinsic 9659-AR-DST.
d. Pfister, Orono F-529-9ONS.
3. Standard duo strainer with tailpiece.
4. Adjustable two-piece chrome plated cast-brass P-trap with cleanout with escutcheon.
5. 1/2" I.P.S. x 3/8" O.D. loose key angle stop supplies with flexible risers and 1/2"
chrome plated nipples and escutcheons.
6. Insulate waste and water supplies.
D. Sink (SK-4): 16" x 20" O.D., single compartment, 18-gauge stainless steel, under mount sink,
center drain, with 9" deep bowl.
1. Fixture: PROFLO PFU303.
2. Faucet: Kohler Faucets, K-596 single handle lever, pull down faucet, 1.8 GPM flow
rate.
3. Standard duo strainer with tailpiece.
4. Adjustable two-piece chrome plated cast-brass P-trap with cleanout with escutcheon.
5. 1/2" I.P.S. x 3/8" O.D. loose key angle stop supplies with flexible risers and 1/2"
chrome plated nipples and escutcheons.
2.08 FOOD WASTE DISPOSERS:
A. Food Waste Disposer (WD-1): Continuous feed, 120 Volt, 60 Hz, 1725 RPM, 1/2 HP motor
with overload protector and manual reset, splash guard and stopper, cord with plug. Two-year
warranty on parts and in-home service.
1. GE model GFC525V.
2. Kenmore model 22-70211, cord 22-70186.
2.09 MOP BASINS:
A. Mop Basin (MB-1): 24" x 24" x 10”, molded stone receptor with brass drain body, stainless
steel dome strainer-lint basket, vinyl bumper guards on exposed mop basin rims.
1. E.L. Mustee and Sons, Inc., Model 63.
2. E.L. Mustee and Sons, Inc., Model 63.600A, supply fitting with integral stops, vacuum
breaker, bucket hook, wall brace, and hose end spout. Provided with inline supply
check valves.
3. 31" long heavy-duty cloth reinforced rubber hose with stainless steel hose bracket.
4. Stainless steel mop hanger with three rubber tool grips, silicone sealant.
THE KENT
22 40 00 - 9
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
5. Vinyl bumper guards on exposed rims.
6. 12” high wall guard panels and corner bracket made with 20-gauge, 304 stainless
steel and mounting hardware.
2.10 TUB-SHOWERS:
A. Tub-Shower (TS-1): One-piece white compression molded solid ‘Vikrell’ material, above floor
drain rough-in, tub – shower, right or left-hand drain, above floor rough–in:
1. Tub-Shower: Sterling, Ensemble 71101112 / 71101122.
2. Pressure balancing mixing valve with maximum temperature limit stop set in field for
110°F, meeting ANSI A112.18; provide tub spout with integral diverter, with check
stops, 1.75 GPM shower head, arm, and flange: PROFLO, PF7611SCP with PF3001
valve series.
3. Drain waste opening lift and turn, and overflow, chrome plated finish, P-trap.
B. Tub-Shower (TS-2): ADA compliant, One-piece white compression molded solid ‘Vikrell’
material, above floor drain rough-in, tub – shower, right or left-hand drain, above floor rough–
in:
1. Tub-Shower: Sterling, Ensemble 71101112 / 71101122.
2. Pressure balancing mixing valve with maximum temperature limit stop set in field for
110°F, meeting ANSI A112.18; provide tub spout with integral diverter, with check
stops, shower head arm, and flange, 1.75 GPM hand held shower head, 60” Meraflex
II hose, chrome plated brass slide bar and mounting hardware.: PROFLO,
PF7611SCP with PF3001 valve series PF14310CP, and PF14BSCP.
3. Drain waste opening lift and turn, and overflow, chrome plated finish, P-trap.
2.11 SHOWERS (UNITS):
A. Shower (SU-1): High gloss finish one-piece white compression molded solid ‘Vikrell’ material,
60”x34”x4-1/2” shower base, 2" center shower drain and strainer assembly, clear glass door
with polished silver frame, hardware, 36”x72” door with side panel:
1. Shower base: Sterling, Ensemble 72131100.
2. Pressure balancing mixing valve with maximum temperature limit stop set in field at
110° F, meeting ANSI A112.18, integral service stops, single blade lever handle, 2.0
GPM shower head, arm and flange: PROFLO, PF7660SCP, with PF3001 valve series.
3. Door: Sterling, Proline swinging framed door on continuous hinge, clear glass door
with polished silver frame, hardware, 36”x72” door with side panel: Sterling S4.
B. Shower (SU-2): ADA compliant, 62” x 32” x 78 1/2", white, re-enforced, one-piece, open top,
applied acrylic, smooth wall finish, stainless steel grab bars, fold up white seat, 1/2” beveled
threshold, soap dish, curtain rod, 2” center drain, chrome strainer, collapsible water dam with
end caps, heavy duty weighted vinyl curtain.
1. Shower; Aquatic, 16030BFSC, right or left hand.
2. single control pressure balanced shower mixing valve with vandal resistant lever
handle, adjustable stop screw to limit handle turn, high temperature limit stop set in
field at 110°F, integral screwdriver stops, polished chrome plated finish, in-line
vacuum breaker, vacuum breaker, wall connection and flange, 1.5 GPM hand-shower
head, 60” chrome plated brass hose, quick disconnect connectors, 36” slide bar with
ADA adjustable slide.
THE KENT
22 40 00 - 10
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
3. Delta Faucet;
a. Valve: Delta Faucet rough-in R10000-UWS.
b. Trim: Delta Faucet T13291.
c. Hand – Held and slide bar: Delta RPW324HDF-1.5.
4. Moen Commercial:
a. Valve: Moen, 8371HD.
b. Trim: Moen, T9375
c. Hand – Held and slide bar; equal to Delta RPW324HDF-1.5.
2.12 SHUT-OFF VALVE BOXES:
A. Ice Maker Supply Box (IB-1): Recessed in wall box with cold water 1/4 turn control valve and
water hammer arrester. Mounting height as shown on drawings. Oatey #38680 or approved
equal.
B. Unit Water Shut-Off Valve Boxes (WVB-1): Recessed wall mounted valve box,12”x12”x 4”,
constructed of stainless steel with 16-gauge door and frame with concealed hinge and thumb
turn latch.
1. ACUDOR Products Inc. ARVB or approved equal.
2.13 CLOTHES WASHER BOXES:
A. Washing Machine Box (WB-1): Control box with hot and cold-water control quarter turn valves
and 2” drain connection, frame. Mounting height as shown on drawings. IPS Corporation,
Water Tite, Du-All, dual drain washing machine outlet box; 82052 or approved equal.
B. Washing Machine Box (WB-2): Fire rated recessed washing machine control box with hot and
cold-water control quarter turn valves and 2” drain connection, frame. Box material, PVC resin
and intumescent pad attached. Mounting height as shown on drawings. IPS Corporation, Guy
Gray, “FR-12” WMOB, washing machine outlet box; 82355 or approved equal.
2.14 WASHING MACHINE DRAIN PANS:
A. Washing Machine Drain Pans (WMDP-1): Bases; 27-1/2” x 32-1/2” x 3” deep inside
dimensions, 10.47 gallons capacity; shall be made of flame retardant material, high density
polyethylene with a blemish-resistant surface that will blend attractively with popular appliance
colors. The units shall be impervious to water and resistant to cracking and peeling.
Floodsaver model #WMBD32.
2.15 ACCEPTABLE MANUFACTURERS:
A. Subject to compliance with requirements, provide plumbing fixtures of one of the following:
B. WATER CLOSETS, URINALS, AND LAVATORIES:
1. American Standard
2. Crane Co.
3. Eljer
4. Kohler Co.
5. Mainline
6. Mansfield
THE KENT
22 40 00 - 11
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
7. Proflo
8. Sloan
9. Zurn
10. Approved equal.
C. WATER CLOSET SEATS:
1. American Standard
2. Bemis Mfg. Co.
3. Beneke Corp.
4. Centoco Mfg. Corp.
5. Church Products
6. Kohler Co.
7. Mainline
8. Mansfield
9. Olsonite Corp.
10. Proflo
11. Sperzel Ind.
12. Approved equal.
D. ELECTRIC WATER COOLERS AND DRINKING FOUNTAINS:
1. Elkay Mfg. Co.
2. Filtrine Mfg. Co,
3. Halsey Taylor
4. Haws Drinking Faucet Co.
5. Oasis
E. FIXTURE CARRIERS:
1. J.R. Smith Mfg. Co.
2. Josam Mg. Co.
3. MIFAB
4. Wade Div.
5. Watts Drainage Products
6. Zurn Industries, Inc.
F. SINKS:
1. American Standard
2. Elkay Mfg. Co.
3. Franke
4. Just Mfg. Co.
5. Kohler Co.
6. Moen Commercial
7. Proflo
8. Titan
9. Approved equal
G. FOOD WASTE DISPOSERS:
1. General Electric (GE)
2. In-Sink-Erator
3. Kenmore
THE KENT
22 40 00 - 12
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
4. Kitchenaide
5. Sears
6. Waste King
7. Whirlaway
8. Whirlpool
9. Approved equal
H. STOPS AND SUPPLY TUBING:
1. American Standard
2. Brass Craft (Commercial-Heavy Pattern)
3. Chicago Faucet Co.
4. Kohler Co.
5. McGuire
6. T & S Brass and Bronze Works. Inc.
7. Zurn Aqua-Spec
I. LAVATORY/SINK P-TRAPS AND TAILPIECES:
1. American Standard
2. Crane
3. Dearborn
4. Eljer
5. Kohler Co.
6. McGuire
7. Sanitary-Dash
8. Zurn Aqua-Spec
J. LAVATORY/SINK FAUCETS AND TRIM:
1. American Standard
2. Cambridge Brass; Div. of Masco Corp.
3. Chicago Faucet Co.
4. Delta Faucet Co; Div. of Masco Corp.
5. Eljer Plumbing Ware
6. Eastport
7. Elkay Mfg. Co.
8. Kohler Co.
9. Moen Commercial
10. Peerless Faucet
11. Pfister
12. Proflo
13. Speakman
14. Symmons
15. T & S Brass and Bronze Works, Inc.
16. Zurn Aqua-Spec
17. Approved equal
K. ADA INSULATION KITS
1. Plumberex
2. SKAL – GARD
3. Truebro
THE KENT
22 40 00 - 13
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
L. SERVICE SINK/MOP RECEPTOR FAUCETS AND TRIM:
1. Cambridge Brass; Div. of Masco Corp.
2. Chicago Faucet Co.
3. E.L. Mustee and Sons, Inc.
4. Fiat Products, Inc.
5. Speakman
6. Zurn Aqua-Spec
7. Approved equal
M. FLOOR MOUNTED MOP RECEPTORS:
1. Creative Industries Terrazzo, Products, Inc.
2. E.L. Mustee and Sons, Inc.
3. Fiat Products, Inc.
4. Stern-Williams, Co., Inc.
5. Swan Corp
6. Approved equal
N. CONVENTIONAL SHOWER AND SHOWER VALVES
1. American Standard
2. Chicago Faucet Co.
3. Delta Faucet Co
4. Eastport
5. Kohler Co.
6. Leonard Valve Co.
7. Peerless Faucet
8. Proflo
9. Powers Regulator Co.
10. Speakman Co.
11. Symmons Ind., Co.
12. Zurn Aqua-Spec
13. Approved equal
O. SHUT-OFF VALVE BOXES:
1. Acorn Engineering Co.
2. ACUDOR Products Inc
3. Guy Gray
4. IPS Corp.
5. Oatey
6. Approved equal
P. CLOTHES WASHER SUPPLY BOXES:
1. Acorn Engineering Co.
2. Guy Gray
3. IPS Corp.
4. Oatey
5. Approved equal
THE KENT
22 40 00 - 14
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
Q. WASHING MACHINE DRAIN PANS:
1. E.L. Mustee and Sons, Inc.
2. Floodsaver
3. Oatey
4. Driptite
5. Whirlpool
6. Approved equal
PART 3 - EXECUTION
3.01 INSPECTION:
A. Installer of rough-in work of potable water and waste piping systems to verify actual locations
of piping connections prior to installing fixtures. Examine floors and substrates, and conditions
under which fixture work is to be accomplished. Correct any incorrect locations of piping, and
other unsatisfactory conditions for installation of plumbing fixtures. Do not proceed with work
until unsatisfactory conditions have been corrected in manner acceptable to Installer.
3.02 INSTALLATION OF PLUMBING FIXTURES:
A. General: Install plumbing fixtures of types indicated where shown and at indicated heights: in
accordance with fixture manufacturer's written instructions, rough-in drawings, and with
recognized industry practices. Ensure that plumbing fixtures comply with requirements and
serve intended purposes. Comply with applicable requirements of The Americans with
Disabilities Act of 1990, The Indiana Handicapped Code, ANSI A117.1 and The Plumbing
Code pertaining to installation of plumbing fixtures.
1. Refer to Architectural drawings for fixture mounting height.
B. Fasten plumbing fixtures securely to indicated supports or building structure; and ensure that
fixtures are level and plumb. Install all hardware, supports and fasteners provide with each
fixture. Secure plumbing supplies behind or within wall construction so as to be rigid, and not
subject to pull or push movement.
C. Protect installed fixtures from damage during remainder of construction period.
D. Caulk around all wall or floor mounted fixtures using nonporous-bond silicone rubber
mold/mildew resistant acid type sealant depositing a uniform continuous ribbon without gaps
or air pockets, and with complete "wetting" of joint bond surfaces equally on opposite sides.
Fill sealant rabbet to a slightly concave surface, slightly below adjoining surfaces. Where
horizontal joints are between a horizontal and vertical surface, fill joints to form a slight cove,
so that joint will not trap moisture and dirt.
E. Waterproof each shower room floor above ground by providing a completely waterproof pan
constructed in place using 40 mil chlorinated polyethylene sheets (Chloraloy 240). Install using
manufacturers recommended procedure and in accordance with the Plumbing Code. Joints
and/or seams shall be welded type with comer ears first folded and then welded. Fabrication
of pan shall be coordinated with the shower wall construction, with the fitting of the tile of prime
importance.
THE KENT
22 40 00 - 15
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
F. Flush Controls designated as "barrier free" which are hand operated or automatic shall comply
with The Americans with Disabilities Act of 1990, Article 4.16.5 and 4.27.4. Controls for flush
valves shall be mounted on the wide side of toilet areas no more than 44 inches above the
floor to centerline of trip lever/push button for use by adults.
G. Do not allow use of fixtures for temporary facilities unless expressly approved in writing by the
Owner.
H. Fire Barrier Penetrations: Where plumbing fixture, and pipes pass through time rated fire
resistive construction including fire rated walls, partitions, ceilings, and floors, maintain the fire
rated integrity. Refer to Division-7 for special sealers and materials.
3.03 FIELD QUALITY CONTROL:
A. Upon completion of installation of plumbing fixtures and after units are water pressurized, test
fixtures to demonstrate capability and compliance with requirements. When possible, correct
malfunctioning units at site and then retest to demonstrate compliance: otherwise, remove and
replace with new units and proceed with retesting.
B. Inspect each installed unit for damage to finish. If feasible, restore and match finish to original
at site; otherwise, remove fixture and replace with new unit. Feasibility and match to be
judged by Architect/Engineer. Remove cracked or dented units and replace with new units.
3.04 ADJUSTING AND CLEANING:
A. Clean plumbing fixtures, trim and strainers of dirt and debris upon completion of installation.
B. Adjust water pressure at drinking fountains, faucets, shower valves, and flush valves to
provide proper flow stream and specified gpm.
C. Adjust or replace washers to prevent leaks at faucets and stops.
3.05 EXTRA STOCK:
A. General: Furnish special wrenches and other devices necessary for servicing plumbing
fixtures and trim to Owner with receipt. Furnish one device for every 10 units.
END OF SECTION
THE KENT
22 40 00 - 16
THE KENT Issue Date 05.09.18 PLUMBING FIXTURES
THE KENT
THIS PAGE INTENTIONALLY LEFT BLANK