HomeMy WebLinkAboutOil Water SeparatorSPECIFICATIONS
1. 4" Plain End inlet/outlet
2. Max flow rate: 75 GPM
3. Capacities: Liquid: 110 gal. (14.7 cu. ft.); Oil: 93 gal.; Sand: 11 gal.
4. Unit weight with composite cover: 130 lbs.; with cast iron cover:
188 lbs.
5. Maximum operating temperature 140OF continuous.
6. Highway rated covers: 16,000 lb. capacity.
NOTES
1. Snap -in Flow control (ships with unit).
2. For gravity drainage applications only.
Do not use for pressure applications.
3. Seamless medium density polyethylene tank.
4. Unit supplied with built-in adapter for up to 6" of
adjustability. Additional riser(s) available for deeper
burial depth.
5. Cover placement allows full access to tank
for proper maintenance.
6. Narrow footprint allows clearance through doorways and down
stairs.
7. Engineered inlet and outlet diffusers are removable to
inspect/clean piping.
8. For on the -floor or buried applications.
DIFFUSION FLOW TECHNOLOGY
The inlet diffuser splits influent into three paths, creating laminar
flow and utilizing the entire liquid volume of the tank for efficient
oil separation. The calibrated openings greatly reduce influent
turbulence. The influent enters the main chamber without
disturbing the existing oil or sand layers. The bottom of the
outlet diffuser allows only effluent that is free of oil to exit the tank.
ENGINEER SPECIFICATION GUIDE
Striem Oil ReserveTM oil/sand separator model OS-75 shall
be lifetime guaranteed and made in USA of seamless,
rotationally -molded polyethylene. Separator shall be furnished for
above or below grade installation, with field adjustable riser system,
snap -in flow control and (2) vent connections. Separator flow rate shall
be 75 GPM. Separator oil capacity shall be 93 gallons. Sand capacity
shall be 11 gallons. Covers shall provide water/gas-tight seal and have
a maximum 16,000 lbs load capacity.
THIRD PARTY STRUCTURAL ANALYSIS
The OS-75 has been structurally analyzed in accordance with the
requirements of IBC 2012 and ASCE/SEI 7 for direct burial. The
maximum burial depth and backfill material are specified in our
installation instructions. The structural design has been reviewed and
sealed by a professional engineer registered in the state of California.
A sealed structural analysis report is available upon request.
¢ of :
Open top
inlet diffuser__� 024-1/2"�
Static water
line
19-7/811
OPTIONS
El4M - 4" Male Thread Inlet / Outlet Engineered inlet and-
� of inlet outlet diffuser
❑ 6P - 6" Plain End SCHAO Inlet / Outlet and outlet (see description)
❑ 6M - 6" Male Thread Inlet / Outlet
❑ C24-HP - H2O Rated Pickable Cast Iron Cover SECTION "A -A"
❑ CC24 - Integral Membrane Clamping Collar Kit
❑ CS2 - Clean Sweep Coalescing Media
❑ AK1 - High Water Anchor Kit
TeleGlide RISER OPTIONS MODEL NUMBER:
❑ SR24 - >611-2411
❑ LR24 - >2411-3911 DESCRIPTION:
RELEASED FOR CONSTRUCTION
Subject to compliance with all regulations
of State and Local Codes
City of Camel
PTY OF "RIEM,
OF
IISSION OF SIRIEM, LLC.IS
DATE: 05/16/19
13" vent
lutlet
Adjustable
adap
Tie -down po
for anchor
Closed top
outlet diffuser
to provide sewer
gas trap
q of 3" vents
OS-75
75 GPM POLYETHYLENE OIL/SAND SEPARATOR
DWG BY: MJ I DATE: 10/02/18 IREV: 0
ISOMETRIC VIEW
Finished grade
See options to
determine available
dimension range
OUTLET END VIEW
Striem S T R I E
Brinkerhoff
Kansas City, KS 66115
Tel:
913-222-1500
Fax: 913-291-0457
www.striemco.com
Made in the U.S.A
-