Loading...
HomeMy WebLinkAbout126-10011-Mulligan-Front ElevMAIN LEVEL 0" MAIN LEVEL 0" UPPER LEVEL 11'-2 1/8" UPPER LEVEL 11'-2 1/8" T.O. FOOTING -11'-2 1/8" T.O. PL - UPPER LEVEL 20'-3 5/8" APPROX T.O. ROOF 34'-9 11/16" T.O. FOUNDATION -1'-2 1/8" T.O. SLAB -10'-10 1/8" T.O. SLAB -10'-10 1/8" T.O. PLATE 10'-1 1/2" ACTUAL GRADE TO BE DETERMINED ON SITE VERIFY ACTUAL NUMBER OF STEPS AND HEIGHTS w/ FINAL GRADE, TYP © 2019 ARTHUR RUTENBERG HOMES, INC.9'-1 1/2"1'-0 5/8"10'-1 1/2" 1'-2 1/8" 9'-8" 4" T.O. GARAGE SLAB -3'-9" KIDS LOUNGE 9'-11 1/4" BATH 4 12'-2 1/8"1'-0"10:1210:1210:125:1210:1210:125 12 12 12 14 12 14 12 14 12 14 12 SHINGLE ROOF T.O. PL - GARAGE 8'-6 1/2" T.O. PL - DORMER ELEV 27'-5 1/8" T.O. PL - DORMER ELEV 20'-3 5/8" T.O. PL - DORMER ELEV 18'-2 1/2" T.O. PL - DORMER ELEV 10'- 1 1/2" 10 12 10'-6" 8'-0"1'-4"6'-8" 8'-0"1'-4"6'-8" 8'-0" 8'-0"8'-0"8'-0"8'-0"7'-0"8'-0" 1'-4"6'-8" 8'-0"30" x 30" HDR AT 26'-4" FG 30" x 30" HDR AT 26'-4" FG 30" x 30" HDR AT 26'-4" FG HARIDEPLANK LAP SIDINGE W/ 6" REVEAL, TYP 5/4x6” HARDIETRIM CORNER TRIM OR EQ, TYP 5/4X6" HARDIETRIM OR EQ STANDING SEAM METAL ROOF CONCEALED FLASHING TYP AT ALL WALL/ROOF CONNECTIONS SMOOTH FINISH HARDIE PANEL 4/4X8" HARDIETRIM OR EQ SMOOTH FINISH HARDIE PANEL BRICK VENEER CONT BRICK ROWLOCK SILL SLOPED FULL BED STONE PER SPECS 6h 16 CONCEALED FLASHING TYP AT ALL WALL/ROOF CONNECTIONS SMOOTH FINISH HARDIE PANEL OR EQ W/ 1X2 VERTICAL BATTEN STRIPS 8" x 30" HDR AT 23'-3" LOUVER VENT 6h 17 8" stone header WINDOW WELL W/ BRICK VENEER & BRICK ROWLOCK SILL 6 1 BOXED WOOD COLUMN, SEE DETAIL 1/6 5/4X10" HARDIETRIM OR EQ CONT SLOPED brick SILL 5/4X8" HARDIETRIM 4/4X8" HARDIETRIM3:129'-0"4" 4x6 corbels (typ) T.O. PL - DORMER ELEV 10'- 1 1/2" chimney w/ brick veneer for b-vent fireplace at great room decorative metal cap per specs 2'-0"5/4x10" hardietrim SMOOTH FINISH HARDIE PANEL5:12 1'-0" 8"1'-0"4'-4" 3'-8" 4" MAIN LEVEL 0'-0" 1X8 trim 1X4 trim 12" sq boxed column 1x6 trim 8" sq boxed column 1X4 trim 1 1/2" thk sloped wood cap 8" sq boxed column smArthur RutenbergHomesPLAN DISCLAIMERARTHUR RUTENBERG HOMES INC., THE DESIGNER, IS RESPONSIBLE FOR THE AESTHETIC DESIGN ONLY AS REPRESENTEDIN THESE DRAWINGS (PLANS), BUT NOT FOR ANY STRUCTURAL INFORMATION INCLUDED OR OMITTED. THE CONTRACTOR(BUILDER) IS RESPONSIBLE BOTH FOR CONFORMING THESE PLANS AND CONSTRUCTING THE RESIDENCE TO ALLAPPLICABLE FEDERAL, STATE, AND LOCAL BUILDING CODES, ORDINANCES, AND LAWS, INCLUDING BUT NOT LIMITED TOTHE FOLLOWING: EGRESS, FIRE SAFETY, TECHNICAL CODES, FLOOD ZONE CRITERIA, HURRICANE CODES, PRE-ENGINEERED TRUSSES, FRAMING MEMBERS, FLASHING, AND MOISTURE PROTECTION. BY USE OF THESE DRAWINGS THEOWNER, CONTRACTOR (BUILDER), AND SUBCONTRACTORS ACKNOWLEDGE AND AGREE TO THIS DISCLAIMER.ALL RIGHTS RESERVED ARTHUR RUTENBERG HOMES, INC.COPYRIGHT6 A CUSTOM PLAN FOR THE MULLIGAN RESIDENCEFRONT ELEVATION PLAN: CUSTOM PLANJOB: 126-10011 - DCI #S 1-58Christopher Scott Investments, Inc.736 Hanover Place, Suite 100FCarmel, IN 460322/20/19 - SHC4/9/19 - A - TK305/10/19 SWH - B06/14/19 DCC - C06/20/19 DCC - C207/23/19 WF3 - D· FLAT SOFFIT AT PERIMETER OF HOUSE UNLESS NOTED OTHERWISE. · VERIFY ALL WDW & DR ROUGH OPNGS W/ MFR SPECS. · LOCATE ALL PLUMBING STACKS BEYOND THE FRONT ELEV ROOF RIDGES, IF ALLOWABLE PER CODE. · ROOF VENTS SHOWN FOR LOCATION PURPOSE ONLY. · NUMBER OF ROOF VENTS TO BE DETERMINED BY BUILDER. GENERAL NOTES: !! ATTENTION !! NOTE: IT IS THE RESPONSIBILITY OF THE BUILDER TO COORDINATE THE INSTALLATION OF ALL WATER PROOFING METHODS NECESSARY TO PROVIDE A WATER TIGHT BUILDING ENVELOPE. REFER TO MFR. INSTALLATION RECOMMENDATION FOR ALL SELECTED WATERPROOFING MATERIALS, FLASHING, SEALERS AND AD-MIX COMPONENTS THE FRAMING PLANS REPRESENTED IN THESE DRAWINGS ARE INTENDED TO ESTABLISH PROPOSED FRAMING MEMBER LOCATIONS, FRAMING MEMBER DEPTH, POTENTIAL BEARING LOCATIONS AND ELEVATIONS, AND IS IN NO WAY INTENDED OR TO BE INTERPRETED AS STRUCTURAL ENGINEERED DRAWINGS. THE CONTRACTOR (BUILDER) SHALL ENSURE THAT THE STRUCTURE CONFORMS TO THOSE STRAINS, LOADS, CONNECTIONS, AND STABILITY. REFER TO PLAN DISCLAIMER LOCATED ON THIS SHEET FOR ADDITIONAL STIPULATIONS AND REQUIREMENTS. Framing PLAN DISCLAIMER ANY DUCT ROUTING AND HVAC EQUIPMENT SHOWN ON THESE DRAWINGS ARE DIAGRAMMATIC ONLY. THE BUILDER IS SOLELY RESPONSIBLE FOR COORDINATING ALL ASPECTS OF MECHANICAL INSTALLATION WITH ALL TRADES. THE BUILDER SHALL COORDINATE BETWEEN THE PRE ENGINEERED TRUSS MFR. AND/OR FRAMING REQUIREMENTS WITH THE MECHANICAL CONTRACTOR TO ENSURE ADEQUATE SPACE FOR DUCT ROUTING AND EQUIPMENT PLACEMENT AND SUPPORT. HVAC INSTALLATION SHALL BE INSTALLED ACCORDING TO ALL CURRENT STATE AND LOCAL MECHANICAL CODES. MECHANICAL DISCLAIMER 1/4" = 1'-0" FRONT ELEVATION 1/2" = 1'-0" COLUMN DETAIL 1 08/07/19 Mike Sheeks