Loading...
HomeMy WebLinkAboutHanwha_Q_CELLS_Data_sheet_QPEAK_DUO-G5_315-330_2017-07_Rev01_ENThe new Q.PEAK DUO-G5 solar module from Q CELLS impresses thanks to innovative Q.ANTUM DUO Technology, which enables particularly high performance on a small surface. Q.ANTUM’s world-record-holding cell concept has now been combined with state-of-the-art circuitry half cells and a six-busbar design, thus achieving outstanding perfor- mance under real conditions — both with low-intensity solar radiation as well as on hot, clear summer days. Q.ANTUM TECHNOLOGY: LOW LEVELISED COST OF ELECTRICITY Higher yield per surface area, lower BOS costs, higher power classes, and an efficiency rate of up to 19.9 %. INNOVATIVE ALL-WEATHER TECHNOLOGY Optimal yields, whatever the weather with excellent low-light and temperature behaviour. ENDURING HIGH PERFORMANCE Long-term yield security with Anti LID Technology, Anti PID Technology1, Hot-Spot Protect and Traceable Quality Tra.Q™. EXTREME WEATHER RATING High-tech aluminium alloy frame, certified for high snow (5400 Pa) and wind loads (4000 Pa). A RELIABLE INVESTMENT Inclusive 12-year product warranty and 25-year linear performance warranty2. STATE OF THE ART MODULE TECHNOLOGY Q.ANTUM DUO combines cutting edge cell separation and innovative wiring with Q.ANTUM Technology. THE IDEAL SOLUTION FOR: Rooftop arrays on residential buildings 1 APT test conditions according to IEC/TS 62804-1:2015, method B (−1500 V, 168 h) 2 See data sheet on rear for further information. ANTI PID TECHNOLOGY (APT) HOT-SPOT PROTECT (HSP) TRACEABLE QUALITY (TRA.Q™) YIELD SECURITY ANTI LID TECHNOLOGY (ALT) www.VDEinfo.comID. 40032587 Quality Tested high reliability low degradation optimized durability continous line monitoring    11/2016 EN Rooftop arrays on commercial / industrial buildings Q.PEAK DUO-G5 315-330 Q.ANTUM SOLAR MODULE MECHANICAL SPECIFICATION Format 1685 mm × 1000 mm × 32 mm (including frame) Weight 18.7 kg Front Cover 3.2 mm thermally pre-stressed glass with anti-reflection technology Back Cover Composite film Frame Black anodised aluminium Cell 6 × 20 monocrystalline Q.ANTUM solar half cells Junction box 70-85 mm × 50-70 mm × 13-21 mm Protection class IP67, with bypass diodes Cable 4 mm² Solar cable; (+) 1100 mm, (−) 1100 mm Connector Multi-Contact, MC4, IP65 and IP68 QUALIFICATIONS AND CERTIFICATES PARTNER Q CELLS PERFORMANCE WARRANTY PERFORMANCE AT LOW IRRADIANCE TEMPERATURE COEFFICIENTS Temperature Coefficient of ISC α [% / K]+ 0.04 Temperature Coefficient of VOC β [% / K]− 0.28 Temperature Coefficient of PMPP γ [% / K]− 0.37 Normal Operating Cell Temperature NOCT [°C]45 NOTE: Installation instructions must be followed. See the installation and operating manual or contact our technical service department for further information on approved installation and use of this product. IRRADIANCE [W/M2] EN RELATIVE EFFICIENCYCOMPARED TO NOMINAL POWER [%]100 95 90 85 80 75 155 2520010 YEARS 98 Q CELLS Industry standard for tiered warranties* Industry standard for linear warranties* *Standard terms of guarantee for the 10 PV companies with the highest production capacity in 2014 (as at: September 2014) ELECTRICAL CHARACTERISTICS POWER CLASS 315 320 325 330 MINIMUM PERFORMANCE AT STANDARD TEST CONDITIONS, STC1 (POWER TOLERANCE +5 W / −0 W)MinimumPower at MPP2 PMPP [W]315 320 325 330 Short Circuit Current*ISC [A]10.04 10.09 10.14 10.20 Open Circuit Voltage*VOC [V]39.87 40.13 40.40 40.66 Current at MPP*IMPP [A]9.55 9.60 9.66 9.71 Voltage at MPP*VMPP [V]32.98 33.32 33.65 33.98 Efficiency2 η [%]≥ 18.7 ≥ 19.0 ≥ 19.3 ≥ 19.6 MINIMUM PERFORMANCE AT NORMAL OPERATING CONDITIONS, NOC3 MinimumPower at MPP 2 PMPP [W]233.4 237.2 240.9 244.6 Short Circuit Current*ISC [A]8.09 8.14 8.18 8.22 Open Circuit Voltage*VOC [V]37.30 37.54 37.79 38.04 Current at MPP*IMPP [A]7.51 7.56 7.60 7.64 Voltage at MPP*VMPP [V]31.07 31.39 31.70 32.01 11000 W/m², 25 °C, spectrum AM 1.5 G 2 Measurement tolerances STC ± 3 %; NOC ± 5 % 3 800 W/m², NOCT, spectrum AM 1.5 G * typical values, actual values may differ PROPERTIES FOR SYSTEM DESIGN Maximum System Voltage VSYS [V]1000 Safety Class II Maximum Reverse Current IR [A]20 Fire Rating C Push / Pull Load (Test-load in accordance with IEC 61215) [Pa]5400 / 4000 Permitted Module Temperature On Continuous Duty -40 °C up to +85 °C 200 400 600 800 1000 110 100 90 80 Irradiance [W/m²]Relative efficiency [%]RELATIVE EFFICIENCY [%]DETAIL A 16mm 8.5 mm24.5 mm 980 mm 1685mm 4 × Mounting slots (DETAIL A) Frame 1000mm 951 mm 32mm 8 × Drainage holes 352.5mm EN VDE Quality Tested, IEC 61215 (Ed. 2); IEC 61730 (Ed. 1), Application class A This data sheet complies with DIN EN 50380.Specifications subject to technical changes © Hanwha Q CELLS Q.PEAK DUO-G5_315-330_2017-07_Rev01_ENHanwha Q CELLS GmbH Sonnenallee 17-21, 06766 Bitterfeld-Wolfen, Germany | TEL +49 (0)3494 66 99-23444 | FAX +49 (0)3494 66 99-23000 | EMAIL sales@q-cells.com | WEB www.q-cells.com At least 98 % of nominal power during first year. Thereafter max. 0.54 % degradation per year. At least 93.1 % of nominal power up to 10 years. At least 85 % of nominal power up to 25 years. All data within measurement tolerances. Full warranties in accordance with the warranty terms of the Q CELLS sales organisation of your respective country. Typical module performance under low irradiance conditions in comparison to STC conditions (25 °C, 1000 W/m2).