HomeMy WebLinkAboutE201-LIGHTING-PLAN-Rev.061 LIGHTING PLAN
,)ni 11 gral A- 1 My an 1'-f
RELEASED FOR CONSTRUCTION
Subject to compliance with all regulations
of State and Local Codes
City of Camel
�Nt�l�tlawwlnp�
DATE: 10/16/19
Note
Unless otherwise noted on pl an (a), connect all
exit signs (fixture types 'X1I to the room
lighting circuit the exit sign is serving
(ahead of any local switching means).
'NEC-2006, Article 517 compliant dual -
grounding HFC-MCMP cable is required in
all patient care areas:'
General Notes:
A. All 120 volt, 20 amp arcuns over 60' in length shall be
#10 A WG, over 95' shall be #8, over 145'shall be #6.
S. Contractor shall coordinate with all other trades to avoid
conflicts of space.
C. Contractor shall coordinate the exact location of all
dances with all other trades poor to rough -in. Exact
location to be determined in the field.
D. Contractor shall coordinate with the mechanical and
plumbing contractors for exact locations of equipment
prior to rough -in.
E. Refer to sheet E701 for details and symbols.
F. Refer to sheet E601 for electrical riser diagram.
G. Refer to sheet E601 and E602 for electrical schedule(s).
H. Refer to sheet E901 for electrical specifications.
H. Shared neutrals shall not be permitted.
J. Note"H" clips are not acceptabl a for juncfi on box
supporting.
K. Switches shal l be a maximuma48" A.F.F. to the top of
the device unless otherwise noted.
L. Receptaa as, tel ephone Rod son antl television outl ets
shall be a minimum of a19' A.F.F. to the bottom of the
device unless otherwise noted.
M. Where devices are instal led in fire wal Is, the boxes shall
be rated and sealed for instal III in a fire wall.
N. Prontle HACR circuit breakers for all HVAC and
refrigeration equipment.
P. All light fixtures marked EM (Emergency) shall be on a
switched circuit said have an emergency battery pack.
Plan Notes:
O3 0-1N c mmer for MRI#126 lighting control. Verify all
required system components prior to installation and
install per manufacturer requirements.
ORemote external power supply/EMI filter system'11,11 PS'
(see light fixture schedule for more information) for MRI
#126 lighting. Verify all required system components
prior to installation and install per manufacturer
requirements. Maintain all manufacturer required
venfilafion clearances.
OS Existing downlight to be carefully removed in its enfirety
including all associated hardware and return to O.vner's
inventory. Repair existing bulkhead in kind, ready for
finish.
16 Replace existing downlight trim with LED retrom fixture
(fixture type'C3' - refer to light fixture schedule).
W
z�
F-
LU '
Z c 3
0 's
(� m a
z ¢
LL, J a
J �
W O
U
I, t
CERTIFIED BY.
COI RIGHT M Lyrtan; Cusb re"wrinsy mertYk
q,qa and ohm, Propose arm In Aae LUnTim par, .
arena
air. amp am me neor dayse ee�a
Henry xion atl ormat of Tire fyxancollEmom,
3.�`"JEL Lny Kw
No.
_* PE10100876 *_
STATEOE /U:>
"iFS A'DIM>P' G�2 c
t'nxs/ NALEe�.°
tt
0& 0118
liessessessessess-
Z
LU
LU
�Q (LD.!V
N MIT
bassimssss
ra �
Z -p .Resew
ra
L 'a
O
Ln cn :::E —
L1J Z limsss Vf
2C1. o 0
LU Z
M
an emssss
Q
Z �
LU
was
0 Ron,
Q sco
i
r °O
m o 0
z w z
3 u —
w
2 cki
Z � V d
well
J
^0.ai
Z o
FTMM
J X
SHEET NO.
E201