HomeMy WebLinkAboutC8.4 Construction DetailsBELLEVUE
CARMEL, INC8.4REVISIONSCONSTRUCTIONDETAILSCONSTRUCTION DETAILS ASPHALT PAVEMENT LAP JOINT DETAIL TYPE 3 HANDICAP ACCESS RAMPPOND OUTLET CONTROL STRUCTURE (STR.#103)VEHICLE BARRIER POSTPOND CROSS SECTIONEMERGENCY SPILLWAY CROSS SECTION3. CONTRACTORS NOTE: FOR PRODUCT AND COMPANY INFORMATION VISIT www.CADdetails.com/info1. INSTALLATION TO BE COMPLETED IN ACCORDANCE WITH MANUFACTURER'S SPECIFICATIONS.NOTES: REFERENCE NUMBER 011-004f.2. DO NOT SCALE DRAWINGS.OPTIONAL FLOATING DEVICEBOTTOM OF POND 1. THE ONLY ASSEMBLY REQUIRED IS TO ATTACH THE MOTOR HOUSING TO THE BASE, WITH THE HARDWARE PROVIDED ANDTO ATTACH THE FLEXIBLE DISCHARGE HOSE.2. YOU WILL HAVE TO MEASURE THE DEPTH OF THE POND AT THE LOCATION YOU WILL BE INSTALLING YOUR UNIT. CUT YOURFLEXIBLE HOSE 0' TO 3' BELOW THE SURFACE. THE CLOSER TO THE SURFACE THE BIGGER THE WATER BOIL WILL BE. AFTERCUTTING THE HOSE TO PROPER LENGTH ATTACH THE HOSE TO THE DISCHARGE TUBE WITH THE STAINLESS STEEL HOSECLAMP. TIGHTEN SECURELY. THE UNIT IS NOW READ TO BE INSTALED IN YOUR POND.3. YOU YOU WILL NEED TWO (2) PIECES OF NYLON ROPE, ONE TO INSTALL YOUR UNIT WHICH SHOULD BE TWICE THE DEPTHOF YOUR POND AND ONE FOR RETRIEVAL, WHICH CAN EXTEND FROM YOUR OXYMAX® BASE TO SHORE OR FROM YOUROXYMAX® BASE TO YOUR FLOATING DEVICE.4. ONE END OF THE NYLON ROPE FOR YOUR RETRIEVAL LINE SHOULD BE ATTACHED THROUGH THE HOLE DRILLED IN THEOXYMAX® BASE, THE OTHER END SHOULD BE ATTACHED TO A FLOAT DEVICE OR BACK TO THE SHORE LINE. THIS LINEIS USEDTO REMOVE YOUR UNIT FROM THE WATER AFTER IT HAS BEEN INSTALLED.WARNING: NEVER REMOVE YOUR UNIT FROM THE POND BY PULLING ON THE POWER CABLE, DAMAGE TO THE UNIT WILLRESULT AND VOID THE WARRANTY.5. THE NYLON ROPE FOR INITIAL INSTALLATION IS RUN THROUGH THE S-HOOK ON THE UNIT. CAREFULLY LOWER THE UNIT TOTHE BOTTOM OF THE POND, MAKING SURE THE BASE SITS AS FLAT AS POSSIBLE. AFTER THE FINAL PLACEMENT, PULL ONE ENDOF THE ROPE OUT THE S-HOOK, DONT LEAVE THIS ROPE IN THE WATER.6. FOR INITIAL OPERATION, INTRODUCE YOUR OXYMAX® INTO THE PONDS ENVIRONMENT BY SETTING YOUR ON-OFF TIMERTO FOUR HOUR INTERVALS. NOTE: THE INSTALLATION ROPE ON 1-5 HP UNITS ARE RUN THROUGH THE S-HOOK ON THE DISCHARGE TUBE ASSEMBLY.THERE IS ALSO A S-HOOK ON THE FLOATTO TIE THE RETRIEVAL LINE TO. THIS AIDS IN REMOVAL OF UNIT.INSTALLING"S" HOOKINSTALLINGROPERETRIEVALLINESHORE ORFLOATPOND AERATOREXCLUDING EVAPORATION RATES AND EXTENDED DRY PERIODS, CONSTRUCTEDWET PONDS MUST BE ABLE TO HOLD NORMAL POOL ELEVATION. WET PONDSMUST BE LINED WITH A LOW PERMEABILITY LINER IF ONE OR MORE OF THEFOLLOWING ARE EVIDENT; INFILTRATION RATE OF SOILS IN A PROPOSED WET PONDLOCATION POSE A RISK TO THIS REQUIREMENT, IT IS FOUND THAT THE PONDCANNOT MAINTAIN NORMAL POOL DURING THE COURSE OF CONSTRUCTION, OR ITIS FOUND THAT THE POND CANNOT MAINTAIN NORMAL POOL PRIOR TOACCEPTANCE OF ALL INSTALLED IMPROVEMENTS BY THE CITY OF CARMEL. THELINER MUST BE DESIGNED BY A CERTIFIED ENGINEER AND THE LINER MUST BEACCEPTABLE TO THE CITY ENGINEER. LINER DETAILS AND LOCATIONS MUST BEINCLUDED IN AS-BUILT SUBMITTALS.INDIANAPOLIS - TERRE HAUTELAFAYETTE - MUNCIE - NEW ALBANYwww.hwcengineering.com