Loading...
HomeMy WebLinkAboutP8-1 - PLUMBING SCHEDULESNOTES: 1. PROVIDE DEEP SEAL P-TRAP. 2. TOP OF HUB TO BE FLUSH WITH FINISH FLOOR. 3. PROVIDE TRAP GUARD IN HUB DRAIN AND/OR FLOOR DRAIN. 4. TOP OF RIM TO BE FLUSH WITH FINISH FLOOR. 5. PROVIDE WITH 1/2 GRATE COVER. PLUMBING FIXTURE ROUGH-IN NOTES: 1. MOUNTING HEIGHT IS FROM FINISHED FLOOR. 2. WALL MOUNTED WATER CLOSET WITH MANUAL OPERATED FLUSH VALVE. 3. WALL MOUNTED WATER CLOSET WITH ELECTRONIC SENSOR OPERATED FLUSH VALVE. 4. INSULATE DRAIN AND WATER SUPPLIES WITH INSULATION KIT. 5. 27" MINIMUM KNEE CLEARANCE WITH MINIMUM 9" TOE CLEARANCE. 6. MOUNTING HEIGHT IS FROM FINISHED GRADE. 7. LAVATORY INTEGRAL WITH COUNTER. 8. PROVIDE THE CABINET SUPPLIER WITH APPROVED SHOP DRAWINGS SHOWING THE SIZE OF THE REQUIRED OPENING IN THE CABINET ENCLOSURE FOR THE PROPER INSTALLATION OF THE LAVATORY, TRIM OR SINK. 9. PROVIDE ALL COORDINATION, ROUGH-INS, SERVICE LINE PIPING, VALVES AND TRAPS AS REQUIRED FOR THE COMPLETE INSTALLATION OF EQUIPMENT PROVIDED BY OTHERS. 10. WATERLESS URINAL, ROUGH-IN AND CAP 3/4"CW PIPE IN CHASE FOR URINAL FLUSH VALVE. 11. REMOTE DRINKING WATER CHILLER MOUNTED ABOVE CEILING ON SHELF. 12. PROVIDE A TEMPERATURE MIXING VALVE WITH 1/2" TEPID WATER TO E-1. 13. SOLAR POWERED ELECTRONIC HAND WASHING FAUCET. 14. DRINKING WATER SUPPLIED BY REMOTE DRINKING WATER CHILLER MOUNTED ABOVE CEILING ON SHELF. 15. PROVIDE FIRE STOPPING AT WALL PENETRATIONS WITH WATER CLOSET CARRIER, WASTE NIPPLE, THRUST BEARING BOLTS, CW SUPPLY, ETC. NOTES: 1. SET OUTLET TEMPERATURE AT 120 DEG F. 2. SET OUTLET TEMPERATURE AT 140 DEG F. NOTES: 1. DUPLEX ALTERNATING SOFTNER SYSTEM. 2. ROUTE DRAIN LINES TO FLOOR DRAIN OR FLOOR SINK. PROJECT NUMBER DATE CERTIFIED BY: REVISIONS ISSUE DRAWING © 2019 Halstead Architects All Rights Reserved- - - - - - - 100% CONSTRUCTION DOCUMENTS P8.1 20015Owner 09/01/2020 PLUMBING SCHEDULESSitara Indian Restaurant13080 GRAND BOULEVARDCARMEL, IN 46032FLOOR DRAIN SCHEDULE MARK DESCRIPTION DRAIN BODY STRAINER INTEGRAL TRAP VANDAL PROOF SEDIMENT BUCKET FUNNEL INTEGRAL CLEANOUT MANUFACTURER WITH MODEL NUMBER NOTESMATERIALOUTLET SIZE OUTLET TYPE MATERIAL SIZE TYPE FD-1 FLOOR DRAIN CAST IRON 2" NO HUB NICKEL BRONZE 5" ROUND NO NO YES NO NO J.R. SMITH #2005Y 1,3,4 FS-1 FLOOR SINK CAST IRON 4" NO HUB NICKEL BRONZE 12"X12" 1/2 GRATE NO NO NO NO NO ZURN #Z1751-SDC 1,3,4,5 PLUMBING FIXTURE ROUGH-IN SCHEDULE MARK FIXTURE TYPE ROUGH-IN SIZES FIXTURE MOUNTING HEIGHT NOTESWASTE SIZE VENT SIZE CW SIZE HW SIZE L-1 LAVATORY, WALL HUNG, ADA 1-1/2" 1-1/2" 1/2" 1/2" 29" MINIMUM KNEE CLEARANCE 1 SK-1 1 COMPARTMENT PREP SINK 1-1/2" 1-1/2" 1/2" 1/2" N/A 9 SK-2 2 COMPARTMENT PREP SINK 1-1/2" 1-1/2" 1/2" 1/2" N/A 9 SK-3 3 COMPARTMENT SINK 2" - 1/2" 1/2" N/A 9 SK-4 KITCHEN HAND SINK 1-1/2" 1-1/2" 1/2" 1/2" N/A 9 WC-1 WATER CLOSET, FLUSH TANK, ADA 4" 2" 1/2" - 18" FLOOR TO TOP OF SEAT 1 PLUMBING FIXTURE SCHEDULE MARK FIXTURE DESCRIPTION MANUFACTURER AND MODEL TRIM DESCRIPTION MANUFACTURER AND MODEL ACCESSORIES DESCRIPTION MANUFACTURER AND MODEL NOTES L-1 WALL MOUNTED, WHITE VITREOUS CHINA, 20.5"x21.25", FAUCET HOLES ON 4" CENTERS, DRILLED FOR CONCEALED ARM CARRIER. MOUNT LAVATORY WITH SUPPORT CARRIER BOLTED SECURELY TO WALL. TOP OF RIM SHALL BE AT 34" ABOVE FLOOR. DURAVIT #0300600000 SENSOR ACTIVATED MIXING FAUCET, BATTERY POWERED, BRASS CONSTRUCTION, BRUSHED CHROME-PLATED FINISH, CONVENTIONAL SPOUT WITH AERATOR, SINGLE HOLE, PERFORATED GRID STRAINER, SOLID BRASS SOLENOID WITH BUILT-IN FILTER, SOLID BRASS THERMOSTATIC MIXING VALVE MEETING ASSE 1070 REQUIREMENTS WITH ADJUSTABLE TEMPERATURE LIMIT STOP AND INTEGRAL CHECK VALVES, WATERPROOF CONNECTORS AND CABLE. MOUNT CONTROLS AND BATTERIES IN WATERPROOF VANDAL-RESISTANT ENCLOSURE BELOW LAVATORY. MAXIMUM FLOW TO BE 0.5 GPM IN COMPLIANCE WITH ENERGY POLICY ACT OF 2005 AND ASME/ANSI STANDARD A112.18.1M. FAUCET SHALL COMPLY WITH FEDERAL ACT S.3874. PROVIDE RESTRICTIVE DEVICE AS REQUIRED. MOUNT MIXING VALVE UNDER COUNTER/LAVATORY. MIXING VALVE SHALL NOT BE WYE PATTERN STYLE. BRADLEY #S53-3700 QUARTER-TURN 3/8" CHROME PLATED HEAVY BRASS ANGLE SUPPLY STOPS, CHROME PLATED SOFT COPPER SUPPLY LINES, DRAIN AND TAILPIECE, 1-1/4" 17 GAUGE CAST BRASS P-TRAP, SUPPORT CARRIER. MOUNT LAVATORY WITH SUPPORT CARRIER BOLTED SECURELY TO FLOOR. PROVIDE 29" MINIMUM CLEARANCE FROM FLOOR TO BOTTOM OF APRON IN COMPLIANCE WITH LATEST ANSI A117.1 AND ADA STANDARDS, ARMAFLEX WITH TAP IS NOT ACCEPTABLE IN LIEU OF INSULATION KIT. TRUEBRO - LAV-GUARD 1 SK-1 1 COMPARTMENT PREP SINK OWNER PROVIDED OWNER PROVIDED 4" POLYPROPYLENE TAILPIECE AND P-TRAP, QUARTER-TURN BALL VALVE TYPE 3/8" CHROME-PLATED BRASS ANGLE SUPPLIES WITH STOPS, CHROME-PLATED SOFT COPPER SUPPLY LINES. SK-2 2 COMPARTMENT PREP SINK OWNER PROVIDED OWNER PROVIDED 2" POLYPROPYLENE TAILPIECE, QUARTER-TURN BALL VALVE TYPE 3/8" CHROME-PLATED BRASS ANGLE SUPPLIES WITH STOPS, CHROME-PLATED SOFT COPPER SUPPLY LINES. SK-3 3 COMPARTMENT SINK OWNER PROVIDED OWNER PROVIDED 2" POLYPROPYLENE TAILPIECE, QUARTER-TURN BALL VALVE TYPE 3/8" CHROME-PLATED BRASS ANGLE SUPPLIES WITH STOPS, CHROME-PLATED SOFT COPPER SUPPLY LINES. SK-4 KITCHEN HAND SINK OWNER PROVIDED OWNER PROVIDED 1-1/2" POLYPROPYLENE TAILPIECE AND P-TRAP, QUARTER-TURN BALL VALVE TYPE 3/8" CHROME-PLATED BRASS ANGLE SUPPLIES WITH STOPS, CHROME-PLATED SOFT COPPER SUPPLY LINES. WC-1 ACCESSIBLE FLOOR MOUNTED, TANK TYPE, WHITE VITREOUS CHINA, CLOSE COUPLED, SIPHON JET, ELONGATED BOWL, BOLT CAPS, 12" ROUGH-IN, FLOAT VALVE WITH VACUUM BREAKER, CHROME-PLATED TRIP LEVER, INSULATED TANK LINER, 1.28 GALLONS PER FLUSH (MAXIMUM) IN COMPLIANCE WITH ENERGY POLICY ACT OF 1992. TOP OF SEAT SHALL BE AT 16"-17" ABOVE FINISHED FLOOR. FLUSH HANDLE SHALL BE LOCATED ON THE WIDE SIDE OF THE TOILET AND OPERATE WITH NO GREATER THAN 5 LB FORCE IN COMPLIANCE WITH LATEST ADA STANDARDS. VERIFY EQUIPMENT REQUIREMENTS AND ROUGH-IN LOCATIONS. MANSFIELD #137-3173 WHITE, EXTRA HEAVY, OPEN FRONT, INJECTION MOLDED SOLID PLASTIC, CHECK HINGE, STAINLESS STEEL OR PLATED STEEL POSTS AND NUTS. BEMIS #1655C QUARTER-TURN 3/8" CHROME-PLATED HEAVY BRASS ANGLE SUPPLY WITH STOP, CHROME-PLATED SOFT COPPER SUPPLY LINE. GAS WATER HEATER SCHEDULE MARK MANUFACTURER WITH MODEL NUMBER FUEL TYPE HEATING CAPACITY STORAGE CAPACITY (GAL.) UNIT WEIGHT (LBS) NOTESINPUT CAPACITY MBTU EFF RECOVERY GPH TEMP RISE NAVIEN #NPE-240A NATURAL GAS 199.9 96% 11.2 70 - 85 1DWH-1 WATER SOFTENER SCHEDULE MARK MANUFACTURER WITH MODEL NUMBER MAXIMUM CAPACITY MINIMUM CAPACITY SERVICE FLOW RATES BACKWASH FLOW RATE(GPM) RESIN (CU. FT.) SALT STORAGE CAPACITY (LBS) NOTESMAX CAP GRAINS MAX CAP SALT DOSAGE MIN CAP GRAINS MIN CAP SALT DOSAGE CONTINUOUS GPM PEAK WS-1 AQUA SYSTEMS #2750-500 15 150,000 5 100,000 50 65 7 5 375 2 10/20/20