The URL can be used to link to this page

Home My WebLink About41_A802A802 ENLARGED FINISH PLANS AND FINISH SCHEDULEENLAGED FINISH PLAN SCALE: 1/4" = 1'-0"2 PROJECT NUMBER: 2020-007 CERTIFICATION:SITE ARCHITECTUREarchitecture + landscape architectureARCHITECT: SITE ARCHITECTURE architecture + landscape architecture BRAD SMITH, RA | LEED AP 13144 EAST 186TH STREET NOBLESVILLE, IN. 46060 PH: 317.374.8720 E-MAIL: brad@site-architecture.com PROJECT CONTACT: These drawings are intended for construction. 12.23.2020DATE ISSUED: REVISIONS ISSUED: CONSTRUCTION ISSUE SET CARMEL, IN 46033NEEDLER'S FRESH MARKET4755 EAST 126TH STREETTENANT FINISH IMPROVEMENTSTHE ENGINEERING COLLABORATIVE SAM HURT, P.E. 2410 EXECUTIVE DRIVE, SUITE 100 INDIANAPOLIS, IN. 46241 PH: 317.636.3941 E-MAIL: sam@tec-mep.com PROJECT CONTACT: MEP ENGINEER: FLOORING MFG: BENJAMIN MOORE COLOR: WHITE DOVE OC-17 - EGSHELL FINISH TYPE: LATEX PAINT RB-01 MFG: TARKETT | JOHNSONITE COLLECTION: TRADITIONAL 4" TALL VINYL COVE BASE TYPE: RUBBER COVE WALL BASE COLOR: CHARCOAL 20 WG LAC-01 MFG: BY MILLWORKER TYPE: GLOSS WHITE LACQUER - OPAQUE FINISH: CLEAR POLYURETHANE NOTE: REPAIR DAMAGED AREAS AND GRIND SMOOTH AS REQUIRED. CONTRACTOR TO SELECT PRODUCT AND SUBMIT TO ARCHITECT FOR APPROVAL. TYPE: POLISHED CONCRETE FLOORPC-01 WALL PAINT (AND CEILING) PT-01 FINISH SCHEDULE: BASE MILLWORK PT-03 PT-02 SEE FLOORING FINISHESPT-04 WP-01 MFG: MARLITE COLLECTION: SYMMETRIX FRP CUSTOM: 4"X8" SUBWAY TILE LOOK, GLOSS WHITE TILE, RUNNING, BOND, HORIZONTAL. LIGHT GRAY GROUT LOOK TO MATCH GROUT IN TL-01. PANEL SIZE: 4' X 8' WHITE SUBWAY TILE-LOOK FRP ST-01 MFG: WILSONART TYPE: QUARTZ COUNTERTOP COLLECTION: QUARTZ COLOR: ARASHI Q4011 MFG: BENJAMIN MOORE PRODUCT: LATEX FLOOR AND PATIO PAINT TYPE: FLOOR PAINTPT-04 LOW SHEEN ENAMEL N122 COLOR: WHITE 01 NOTE: SEAL WITH PC-01 MFG: BENJAMIN MOORE COLOR: SMOKE EMBERS 1446 - MATTE FINISH TYPE: LATEX PAINT MFG: BENJAMIN MOORE COLOR: CUSTOM MATCH TO PMS 394C - EGGSHELL FINISH TYPE: LATEX PAINT PT-05 MFG: BENJAMIN MOORE COLOR: CUSTOM MATCH TO PMS 360C - MATTE FINISH TYPE: LATEX PAINT DESIGN INTENT: TO MATCH TL-01 WP-02 MFG: 3M COLOR: WG-1815 WOOD LOOK VINYL WALLCOVERING TYPE: DI-NOC ARCHITECTURAL FINISHES WP-03 MFG: TBD LARGE SCALE PATTERN CUSTOM WALLCOVERING TYPE: CUSTOM GINGHAM PATTERN IN GREEN WP-04 MFG: TBD MEDIUM SCALE PATTERN CUSTOM WALLCOVERING TYPE: CUSTOM GINGHAM PATTERN IN YELLOW TL-01 MFG: DALTILE COLLECTION: COLOR WHEEL LINEAR COLOR: ARCTIC WHITE 0190 SIZE: 4 X 8 WHITE SUBWAY TILE GROUT: LATRICRETE SPECTRALOCK EPOXY GROUT - COLOR 78 STERLING SILVER TL-02 MFG: DALTILE COLLECTION: COLOR WHEEL LINEAR COLOR: BLACK K111 SIZE: 4 X 8 BLACK SUBWAY ACCENT TILE GROUT: LATRICRETE SPECTRALOCK EPOXY GROUT - COLOR 78 STERLING SILVER ST-02 MFG: WILSONART TYPE: QUARTZ COUNTERTOP COLLECTION: QUARTZ COLOR: SERENE Q1001 MTL-01 MFG: BY MILLWORKER TYPE: BRUSHED ALUMINUM LAM-01 MFG: WILSONART TYPE: WHITE OAK WOOD-LOOK LAMINATE COLLECTION: STANDARD LAMINATE COLOR: NATURAL RIFT LAM-02 MFG: WILSONART TYPE: WHITE LAMINATE COLOR: DESIGNER WHITE D354 - SATIN FINISH LAM-03 MFG: ABET LAMINATI TYPE: WOOD-LOOK LAMINATE COLLECTION: ROOT FINISH COLOR: 1850 LAM-04 MFG: WILSONART TYPE: WOOD-LOOK LAMINATE COLOR: WHITE BARN SOFT GRAIN FINISH MTL-01 MFG: PRISMATIC POWDERS TYPE: POWDER COATED METAL CUSTOM FURNITURE FINISHES UPH-01 MFG: ULTRAFABRICS TYPE: CUSHION UPHOLSTERY COLLECTION: BRISA | ORIGINAL FINISH: GLOSS COLOR: SUNSHINE YELLOW PSS 2600 COLOR: 533-4302 ESMERELDA XX-00 XX-00 XX-00 XX-00 XX-00 XX-00 XX-00 XX-00 XX-00 VESTIBULE B 111 CASH OFFICE 108 CORR 136 MEN RR 137 WOMEN RR 138 JANITOR 112 ENLAGED FINISH PLAN SCALE: 1/4" = 1'-0"2 WP-02 PC-01 RB-01 F2 F2 TB-01 SS-01 PT-01 RB-01 PT-01 RB-01 SS-01 TL-01 WALL COVERING AND TILE XX-00 XX-00 XX-00 WP-01 RB-01 PT-01 RB-01 PT-01 RB-01 TL-01 TL-03 TL-03 MFG: DALTILE COLLECTION: RETRO ROUNDS COLOR: DAFFODIL YELLOW RR07 DECORATIVE ROUND PENNY TILE GROUT: LATRICRETE SPECTRALOCK EPOXY GROUT - COLOR 78 STERLING SILVER TL-01 PT-03 ST-01 SS-01 MFG: CORIAN TYPE: SOLID SURFACE PATTERN: DOVE FINISH: SATIN THICKNESS: 1/2" EDGE PROFILE: EASED EDGE RB-01 F4 PT-01 PC-01 RB-01 LAM-01 ST-01 F3 F3 PT-01 PC-01 RB-01 TL-01PT-01 RB-01 PT-01 RB-01 PT-01 RB-01 TL-01 LAM-01 RB-01 PT-01 PC-01 RB-01 ST-01F2 F2 F2 ST-01 TL-01 TB-01 INSTALL 1 ROW TL-02 AT BASE OF WALL TYPE: TILE BASE TB-01 TL-01 TB-01 GENERAL FINISH NOTES: FINISH PLAN SYMBOLS: X FINISH PLAN NOTES: FX WALL FINISH TAG (DENOTES DIFFERENT WALL FINISH LOCATIONS) FLOORING TRANSITION ROOM FINISH TAG WALL FINISH BASE FINISH XXX XXX XXX XX-00 F5. BREAK ROOM MILLWORK: BASE CABINET: LAM-01 UPPER CABINET: LAM-01 COUNTER: SS1 TOE KICK: BLACK LAMINATE A. PROVIDE FINISH SAMPLE SUBMITTALS AND PRODUCT DATA FOR ALL NEW FINISH ITEMS FOR ARCHITECT/DESIGNER/OWNER APPROVAL PRIOR TO ORDERING/INSTALLATION/FABRICATION. B. LEVEL ALL EXISTING FLOORS TO 1/4" IN 12'-0" TOLERANCE. C. ALL NEW DOORS SHALL MATCH EXISTING. PROVIDE FINISH SAMPLES TO ARCHITECT FOR VERIFICATION PRIOR TO ORDERING /INSTALLATION. C. ALL PAINT FINISH LOCATIONS TO BE THREE COAT SYSTEM: 1 (ONE) COAT PRIMER 2 (TWO) COATS FINISH -CEILINGS - FLAT -DRYWALL - EGGSHELL -DOOR FRAMES - SEMI-GLOSS D. VERIFY COLOR OF UNDERSIDE OF ALL NEW BULKHEADS WITH ARCHITECT PRIOR TO FINISH PAINT. E. REFER TO DOOR/FRAME SCHEDULE FOR FRAME TYPE AND FINISH. F. FOR ALL NEW FINISH MATERIALS - CAREFULLY FOLLOW ALL MANUFACTURER INSTALLATION INSTRUCTIONS FOR HIGHEST QUALITY WORKMANSHIP AVAILABLE. INSTALLATIONS NOT MEETING ARCHITECT/DESIGNER/OWNER APPROVAL WILL BE REJECTED. G. NOTIFY ARCHITECT OF ANY DIMENSIONAL OR PHYSICAL DISCREPANCIES BETWEEN EXISTING CONDITIONS AND REPRESENTATIONS IN THE DRAWINGS FOR CLARIFICATION PRIOR TO PROCEEDING WITH WORK IN THE AFFECTED AREA. H. PROVIDE A MAINTENNCE MANUAL FOR ALL FINISH GROUTS AND SEALERS AS INSTALLED PRIOR TO OWNER OCCUPANCY. TWO COPIES BOUND AND INDEXED FOR OWNER USE. I. WHERE DISSIMILAR FLOORING MATERIALS MEET THEY SHALL DO SO UNDER CENTERLINE OF DOOR UNLESS NOTED OTHERWISE. J. ALL VERTICAL FACES OF BULKHEADS TO MATCH ADJACENT WALL FINISH UNLESS NOTED OTHERWISE. K. GYPSUM WALLBOARD AT WP-02, WP-03, WP-04, AND UPPER GRAPHICS ABOVE COFFEE SHOP 106 AND CUSTOMER SERVICE 107 TO RECEIVE A LEVEL 5 FINISH. ALL OTHER GYPSUM WALLBOARD TO RECEIVE A LEVEL 4 FINISH UNLESS SPECIFIED OTHERWISE. FLOOR FINISH XX-00 XX-00 F1. -CLEAN EXISTING CMU WALLS, COOLER WALLS, AND COOLER CEILINGS. -PAINT EXISTING CMU WALLS PT-01. -PAINT EXISTING COOLER WALLS AND CEILINGS PT-01 COLOR, BUT USE PRIMER AND FINISH COAT APPROPRIATE FOR METAL SURFACE/COOLER WALLS. -REMOVE EXISTING METAL BASE AT ALL COOLER WALLS. INSTALL NEW BREAK METAL BASE - ATTACH WITH SCREWS TO EXISTING COOLER WALLS. PAINT TO MATCH COOLER WALLS. -IN AREAS WHERE QUARRY TILE HAS BEEN REMOVED FOR UNDERSLAB PLUMBING/ELECTRICAL WORK - INFILL WITH QUARRY TILE TO MATCH EXISTING - FINISH FLUSH WITH ADJACENT QUARRY TILE. -IN AREAS WHERE CONCRETE FLOOR REMAINS AS FINISH - CLEAN AND SEAL CONCRETE. F2. FLOOR FINISH TO BE PC-01. F3. CUSTOM MILLWORK, SEE FLOOR PLAN, EQUIPMENT SCHEDULE, AND INTERIOR ELEVATIONS. F4. 12" DEEP WHITE MELAMINE SHELVING ON ADJUSTABLE STANDARDS. PROVIDE TWO (2) SHELVES. F6. FRP PANELS ABOVE COOLER AREAS TO BEGIN AT 7'-0" A.F.F. AND END AT 14'-6" A.F.F. VERIFY HEIGHTS ON SITE WITH OWNER PROVIDED EQUIPMENT AND COORDINATION WITH ARCHITECT ON BOTTOM OF JOIST ELEVATION. F7. LAM-01 WALL PANELS MOUNTED ON Z CLIPS TO A HEIGHT OF 9'-0" A.F.F. COORDINATE LAYOUT OF SEAMS/REVEALS WITH ARCHITECT DURING SHOP DRAWING PHASE. WP-03 FROM 9'-0" A.F.F. TO 1X2 STRIP AT 14'-6" A.F.F. SEE INTERIOR ELEVATION. F8. LAM-01 WALL PANELS MOUNTED ON Z CLIPS TO A HEIGHT OF 4'-0" A.F.F. COORDINATE LAYOUT OF SEAMS/REVEALS WITH ARCHITECT DURING SHOP DRAWING PHASE. PT-01 FROM 4'-0" A.F.F. TO CEILING ABOVE. INSTALL A WOOD 1X2 STRIP AT 4'-0" A.F.F (TOP OF LAMINATE PANEL - TO BE PAINTED PT-01. F9. FINISH CHANGE TO ALIGN WITH EDGE OF COOLERS. F10. 2"X2" FULL HEIGHT STAINLESS STEEL CORNER GUARD. F11. STAINLESS STEEL WALL PANEL TO EXTEND FROM FLOOR TO BOTTOM OF EXHAUST HOOD. F12. INSTALL NEW RUBBER STAIR TREAD/RISERS - JOHNSONITE OR SIMILAR - COLOR TO BE SELECTED FROM MANUFACTURER STANDARD RANGE OF COLORS. F13. INSTALL STANDARD WHITE FRP PANELS IN MOP SINK AREA. FROM FLOOR TO 5'-0" A.F.F. - EXTEND HORIZONTALLY 2'-0" PAST FACE OF MOP SINK IN BOTH DIRECTIONS. TB-01 F10 WP-04 LEMON'S SEATING 105 LEMON'S CUSTOMER LINE 106 CUSTOMER SERVICE 107 110 LEMON'S F.O.H. SERVICE 109 LEMON'S B.O.H. SERVICE F6 TL-01 PC-01 TB-01 F11 #1 - 1.8.2021 1 F13 PT-01 LAM-01 RB-01 LAM-01 RB-01 LAM-01 RB-01 2 2 2 #2 - 1.18.2021 ST-01 LAM-01 RB-01 2 2 RB-01 WP-02 05/06/21