HomeMy WebLinkAboutGN010.202 41 19 -SELECTIVE DEMOLITION
A. General
1. Demolish and remove existing construction only to the extent required by new construction and as indicated.
2. Locate selective demolition equipment and remove debris and materials so as not to impose excessive loads on supporting walls,
floors, or framing.
3. Dispose of demolished items and materials promptly.
4. Clean salvaged items and store items in secure area until delivery to Owner.
5. Clean and repair items to functional condition adequate for intended reuse. Reinstall items in locations indicated. Comply with installation
requirements for new materials and equipment. Provide connections and supports necessary to make item function for use indicated.
6. Protect construction indicated to remain against damage and soiling during demolition.
7. Clean adjacent structures and improvements of dust, dirt, and debris caused by demolition operations.
03 01 03 -CONCRETE PATCHING/INFILL MATERIAL
A. Polymer-Modified, Cementitious Patching Mortar: Packaged, dry mix for repair of concrete and that contains a latex additive as either a dry
powder or a separate liquid that is added during mixing.
1. Manufacturers: Subject to compliance with requirements, provide products by one of the following:
a. Dayton Superior –Polyfast FS
b. Euclid Chemical Company (The); an RPM company.
c. MAPEI Corporation.
d. Sika Corporation.
e. W.R. Meadows, Inc.
2. Compressive Strength: Not less than 5000 psi at 28 days when tested according to ASTM C 109.
3. Prepare existing concrete slab area, and install per manufacturer’s instructions
05 40 00 -COLD-FORMED METAL FRAMING
A. Ceiling Joist Framing and Soffit Framing.
1. Manufacturers: Subject to compliance with requirements, provide products by one of the following:
a. AllSteel & Gypsum Products, Inc.
b. ClarkWestern Building Systems, Inc.
c. Consolidated Fabricators Corp; Building Products Division
d. Dietrich Metal Framing
e. MarinoWARE
2. Steel sheet and steel-framing accessories: ASTM A 1003/A 1003M, Structural Grade, Type H, metallic coated, of grade and coating
weight as follows:
a. Grade as required by structural performance.
b. Coating: G90 or equivalent.
05 50 00 -METAL FABRICATIONS
A. Metals
1. Metal Surfaces: Provide materials with smooth, flat surfaces unless otherwise indicated. For metal fabrications exposed to view,
provide materials without seam marks, roller marks, rolled trade names, or blemishes.
2. Provide stainless-steel fasteners for fastening aluminum, stainless steel and nickel silver.
3. Anchors capable of sustaining, without failure, a load equal to four times the load imposed when installed in concrete, as determined by
testing according to ASTM E488, conducted by a qualified independent testing agency.
4. Weld corners and seams continuously so that at exposed connections, finish exposed welds and surfaces smooth and blended so no
roughness shows after finishing and contour of welded surface matches that of adjacent surface.
06 10 53 -MISCELLANEOUS ROUGH CARPENTRY
A. Lumber: DOC PS 20 and applicable rules of grading agencies indicated.
B. Maximum moisture content of lumber: 15 percent unless otherwise indicated.
C. Provide miscellaneous lumber indicated and lumber for support or attachment of other construction, including:
1. Blocking
2. Nailers
3. Furring
4. Utility shelving
D. For items of dimension lumber size, provide Construction or No.2 and any of the following species:
1. Hem-fir, NLGA
2. Mixed southern pine, SPIB
3. Spruce, pine-fir, NLGA
E. For blocking and nailers used for attachment of other construction, select and cut lumber to eliminate knots and other defects that will interfere
with attachment of other work.
06 41 16 -PLASTIC-LAMINATE FACED ARCHITECTURAL CABINETS
A. Quality Standard: Unless otherwise indicated, comply with the "Architectural Woodwork Standards" for grades of architectural plastic-laminate
cabinets.
1. Grade: Custom
2. Type of Construction: Frameless.
3. Cabinet, Door, and Drawer Front Interface Style: Reveal overlay.
4. Reveal Dimension: 1/2 inch.
5. High-Pressure Decorative Laminate: NEMA LD 3, grades as indicated.
B. Manufacturers:
1. Abet Laminati
2. Formica
3. Lamin-Art
4. Panolam Industries
5. Wilsonart International
C. Laminate Cladding for Exposed Surfaces:
1. Horizontal Surfaces: Grade HGS.
2. Vertical Surfaces: Grade HGS.
3. Edges: PVC Edge Banding, .12 inch thich, matching laminate in color, pattern and finish.
4. Pattern direction: Vertically for doors and fixed panels, horizontally for drawer fronts.
D. Materials for semiexposed Surfaces:
1. Surfaces other than drawer bodies: High pressure decorative laminate, NEMA LD 3, Grade VGS.
2. Drawer sides and Backs: Solid-hardwood lumber.
3. Drawer bottoms: Hardwood plywood.
E. Wood Products: Provide materials that comply with requirements of quality standard. Wood moisture content: 5 to 10 percent.
F. Composite Wood Products: Provide materials that comply with requirements of quality standard for each type of woodwork unless otherwise
indicated.
1. Medium-Density Fiberboard: ANSI A208.2, Grade 130.
2. Particleboard: ANSI A208.1, Grade M-2.
3. Veneer-Faced Plywood: HPVA HP-1.
G. Cabinet Hardware and Accessories: Provide cabinet hardware and accessories as specified, unless otherwise indicated.
06 46 00 -WOOD TRIM
A. Interior Standing and Running Trim for Transparent Finish
1. Grade: Premium
2. Wood Species and Cut: Maple, Quarter Sawn
3. For trim items wider than available lumber, use veneered construction. Do not glue for width.
B. Wood Cabinets for Transparent Finish
1. Grade: Custom
2. Type of Construction: Frameless
3. Cabinet Door and Drawer Front Interface Style: Flush Overlay.
4. Wood Species and Cut: Maple, Plain Sliced
5. Surfaces other than drawer bodies: Same species and cut indicated for exposed surfaces.
C. Transparent Finish for Interior Trim:
1. Grade: Premium
2. Finish: System - 5, conversion varnish.
3. Wash coat for Closed-Grain woods: Apply wash coat sealer to woodwork made from closed-grain wood before staining and finishing.
4. Staining: Match approved sample for color.
5. Sheen: Satin 31-45 gloss units
07 21 00 -THERMAL INSULATION
A. Glass Fiber Blanket Insulation
1. Manufacturers: Subject to compliance with requirements, provide products by one of the following:
a. CertainTeed Corporation
b. Guardian Building Products
c. Johns Manville
d. Knauf Insulation
e. Owens Corning
2. Unfaced Glass-Fiber Blanket Insulation: ASTM C 665, Type I; with maximum flame spread and smoke-developed indexes of 25 and
50, respectively, per ASTM E 84; passing ASTM E 136 for combustion characteristics.
3. Use insulation widths and lengths that fill the cavities formed by framing members. Provide lengths that will produce a snug fit
between ends.
07 92 00 -JOINT SEALANTS
A. Interior Joints in Horizontal Traffic Surfaces: Silicone, S, NS, 50, T and NT.
1. Manufacturer: Dow Corning Corporation
B. Interior Joints in Vertical Surfaces and Horizontal Nontraffic Surfaces: Urethane, M, NS, 50, NT
1. Manufactures:
a. Pecora Corp.; Dynatrol II
b. Tremco Inc.; Dymeric 240
c. BASF Corp.; NP2
C. Acoustical Sealants
1. Manufacturers:
a. DAP Dynaflex 230
b. GE SCS 7000
c. Sikaflex 1a
D. Joint Sealant Backing
1. Cylindrical Sealant Backings: Type C (closed cell material with a surface skin)
E. Color to be selected by architect from manufacturer’s full range
F. Provide accessories, tape, and primers as required, and install sealants per manufacturer’s instructions.
08 14 16 –FLUSH WOOD DOORS
A. Manufacturers:
1. Algoma
2. Eggers
3. Graham
4. Marlite
5. Marshfield
6. Mohawk Doors
B. Interior Solid-Core Doors with wood veneer facing and factory finished transparent stain:
1. Grade: Grade A faces
2. Species: Select White Maple
3. Cut: Plain Sliced
4. Match between veneer leafs: Pleasing Match
5. Core: Particleboard
6. Construction:
a. Five or Seven Face Plies.
b. Stiles and rails are bonded to core.
c. Entire unit is abrasive-planed before veneering.
d. 5 inch top and bottom rail blocking for hardware.
e. Factory-mortised hinge pockets, factory laminated-edges with improved screw-holding capacity, and factory cutouts to accept all selected door
hardware.
7. Glass Stop: Wood beads / glass stops for lite opening shall be in species compatible with door faces and profile per manufacturer’s standard shape.
8. Staining Finish: As indicated on drawings.
9. Sheen: Satin
08 71 00 -DOOR HARDWARE
A. Mechanical hardware for swinging doors.
B. Coordinate keying with Owner’s Lock Master; Basis-of-design = Schlage Saturn Series or match existing. Coordinate with owner.
C. Manufacturers:
1. Hinges: Hager, Ives, McKinney, Stanley.
2. Mechanical Locks: Schlage Saturn.
3. Flush Bolts: Ives, Rockwood.
4. Lock Cylinders: Schlage Saturn.
5. Surface Closers: Norton.
6. Overhead Stops and Holders: Glynn Johnson, Rockwood, Sargent.
7. Door Gasketing and Thresholds: National Guard, Pemko, Reese, Zero.
8. Metal Protective Trim Units: Ives, Rockwood - .050 inch
D. Coordinate door hardware with door and frame manufacturers to insure proper reinforcement and preparations has been provided.
E. Install hardware per manufacturer’s instructions.
F. Door Hardware Schedule:
HW SET: 1 New Office Passage Set - Match Existing Office Hardware
HW SET: 2 New Flex Office Privacy Lockset - Match Existing Office Hardware
08 80 00 -GLAZING
A. Glass Type CTG: Clear tempered glass
1. Manufacturers:
a. Guardian Industries
b. Viracon
c. AGC
2. Overall Unit Thickness: 1/4 inch
B. Glass Type FG1: Frosted glass (White Laminated Glass)
1. Manufacturers:
a. Guardian Industries
b. Viracon
c. AGC
2. Overall Unit Thickness: 1/4 inch
09 22 16 -NON-STRUCTURAL METAL FRAMING
A. Framing Members: Use either steel studs and runners or embossed steel studs and runners.
1. Minimum Base Metal Thickness:
a. Standard Framing: 0.0329 inch
b. Embossed Framing: 0.0221 inch
2. Depth: As indicated.
3. Provide slip-type head joints as required.
4. Spacing: 16 inches o.c.
5. Brace wall framing to structure above, as required for stable wall.
B. Rigid Furring Channels: 7/8 inch, hat-shaped channels
1. Protective Coating: ASTM A 653A G60 hot-dip galvanized.
2. Minimum Base Metal Thickness: 0.0329 inch
3. Spacing: 16 inches o.c.
C. Sound-Attenuation Insulation: Thermafiber SAFB –2.5 p.c.f. density
1. Provide batt insulation in partition walls where indicated.
09 29 00 -GYPSUM BOARD
A. Interior Gypsum Board: ASTM C 1629/C 1629M
1. Core: Type X
2. Thickness: 5/8 inch
3. Long Edges: Tapered
4. Mold Resistance: ASTM D 3273, score of 10 as rated according to ASTM D 3274
B. Interior Trim
1. Galvanized steel sheet or rolled zinc shapes.
2. Shapes:
a. Cornerbead
b. LC-Bead: J-shaped; exposed long flanges receives joint compound.
c. L-Bean: L-shaped; exposed long flange receives joint compound.
d. Expansion (control) joint.
C. Joint Treatment Materials:
1. Drying-type all-purpose compound
2. Paper joint tape
3. GWB Finish Level: Level 4: At exposed paper-faced panel surfaces
D. Control Joints: Provide on each side of openings, spaced not more than 30’-0” o.c. in uninterrupted walls.
09 51 13 -ACOUSTICAL CEILING PANELS
A. Acoustical Ceiling Panels
1. Basis of Design: As indicated on drawings.
a. Edge Detail: As indicated.
b. Modular Size: 24 inches by 24 inches
B. Wide-Face, Capped, Double-Web Suspension System
1. Basis of Design: As indicated on drawings, Existing to Remain.
C. Accessories
1. Provide attachment devices, hangar wire, edge moldings, supplemental framing and trim for a complete installation.
D. Install acoustical ceiling panels per ASTM C636/C636M, reflected ceiling plan, and manufacturer’s directions.
09 65 13 -RESILIENT BASE AND ACCESSORIES
A. Rubber Base: Subject to compliance with requirements, provide products by one of the following:
1. Armstrong World Industries
2. Johnsonite
3. Roppe Corporation
4. VPI Corporation
B. Product Standard: ASTM F 1861, Type TP (rubber); Basis-of-design is Johnsonite Baseworks
1. Group: I (solid, homogeneous)
2. Style: Coved
3. Thickness: 0.125 inch
4. Height: 4 inches
5. Lengths: Roll-lengths to minimize cuts and transitions
6. Corners: Preformed
7. Color: Per finish schedule
C. Provide vinyl molding accessories at terminations and flooring type transitions, as required.
09 68 13 -TILE CARPETING
A. Modular Carpet Tile: CPT-1/2 - Product is as follows:
1. Manufacturer: Milliken
2. Patterns - Per Finish Schedule.
B. Installation & Accessories:
1. Provide carpet adhesive and install over suitable substrate per manufacturer’s instructions.
2. Trowelable leveling and patching compounds: Where leveling compound is required per field inspection or manufacturer’s instructions,
provide latex-modified, hydraulic-cement-based formulation, as approved by manufacturer.
09 91 23 -INTERIOR PAINTING
A. Manufacturer: Sherwin Williams
B. Painting Schedule
1. Steel and Galvanized Metal Surfaces
a. Alkyd System: Door Frames
1) Prime Coat: S-W Pro Industrial Pro-Cryl Universal Primer B66-310 Series
2) Intermediate Coat: S-W ProClassic XP Alkyd Semi-Gloss B34W551
3) Topcoat: S-W ProClassic XP Alkyd Semi-Gloss B34W551
3. Gypsum Board Substrates
a. Latex System
1) Prime Coat: S-W ProGreen 200 Interior Latex Primer B28W600
2) Intermediate Coat: S-W ProGreen 200
3) Topcoat: S-W ProGreen 200; B20-650 Series Eg-Shel
C. Prepare surface for painting per manufacturer’s directions. Sand previously painted surfaces, or remove existing surface as required to allow for
refinishing.
D. Colors to be selected by Owner or Architect from full range of available colors. Refer to finish schedule.
09 93 00 -STAINING AND TRANSPARENT FINISHING
A. Manufacturer: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include,
but are not limited to, the following:
1. Behr Process Corporation
2. Benjamin Moore & Co.
3. California Paints
4. Duron, Inc.
5. ICI Paints
6. Sherwin Williams Company
C. Clean and prepare surfaces to be finished according to manufacturer’s instructions for each particular substrate condition and as specified.
Remove dust, dirt, oil, grease by washing with a detergent solution; rinse thoroughly with clean water and allow to dry. Remove grade stamps and
pencil marks by sanding lightly. Remove loose wood fibers by brushing.
D. Colors to be selected by Owner or Architect from full range of available colors. Refer to finish schedule.
10 44 16 -FIRE EXTINGUISHERS
A. NFPA Compliance: Fabricate and label fire extinguishers to comply with NFPA 10, "Portable Fire Extinguishers"
1. Manufacturers: Subject to compliance with requirements, provide products by one of the following:
a. Guardian Fire Equipment, Inc.
b. JL Industries Inc.
c. Larsens Manufacturing Company
2. Identification: Lettering complying with authorities having jurisdiction for letter style, size, spacing and location. Locate as indicated.
3. Identify bracket-mounted fire extinguishers with the words "FIRE EXTINGUISHER" in red letter decals applied to mounting surface.
12 36 23.13 -PLASTIC-LAMINATE-CLAD COUNTERTOPS
A. Quality Standard: Unless otherwise indicated, comply with the "Architectural Woodwork Standards" for grades indicated for construction, installation,
and other requirements.
1. Grade: Custom
2. High-Pressure Decorative Laminate: NEMA LD 3, grade HGS.
B. Manufacturers:
1. Abet Laminati
2. Formica
3. Lamin-Art
4. Panolam Industries
5. Wilsonart International
C. Grain Direction: Parallel to cabinet fronts.
D. Edge Treatment: Same as laminate cladding on horizontal surfaces and as indicated on drawings.
E. Core Material: Particleboard or medium-density fiberboard.
F. Core Material at Sinks: Particleboard made with exterior glue, medium-density fiberboard made with exterior glue, or exterior grade plywood.
G. Core Thickness: 3/4 inch. Build up countertop thickness to 1 1/2 inches at front, back, and ends with additional layers of core material laminated to top.
H. Wood Products: Provide materials that comply with requirements of quality standard. Wood moisture content: 5 to 10 percent.
I. Composite Wood Products: Provide materials that comply with requirements of quality standard for each type of woodwork unless otherwise
indicated.
1. Medium-Density Fiberboard: ANSI A208.2, Grade 130.
2. Particleboard: ANSI A208.1, Grade M-2.
3. Softwood Plywood: DOC PS 1.
12 36 61 -SIMULATED STONE COUNTERTOPS
A. Manufacturer: Corian
B. Size: 1/2" top, side- and back-splashes, where indicated on drawings.
C. Pattern / Color: Graylite
NOT
F
O
R
CON
S
T
R
U
C
TI
O
N
See Drawing
CERTIFICATION
626 North Illinois Street
Indianapolis, Indiana 46204
Phone: (317) 635-5030
Website: www.browningday.com
Checked By:
Scale:
Issue Date:
Drawn By:
Project No.:
Owner
6/16/2021 4:18:44 PM \\bdmd.local\UEM\UserShare\kthompson\Documents\FORUM_Carmel Reno_kthompson.rvt0.02
Specifications
21I010
Author
Checker
6/15/21
FORUM Credit Union
Branch Renovation
2259 E 116th Street,
Carmel, IN 46032
Construction Documents
11313 USA Parkway
Fishers, IN 46038
Phone: (317) 558-6000
Website: www.forumcu.com
FORUM Credit Union
9229 Delegates Row, Suite 150
Indianapolis, IN 46240
Phone: (317) 781-6200
Website: www.circledesigngroup.com
Circle Design Group
MEP Engineer
REVISION SCHEDULE
Rev. # Revision Description Issue Date
07/06/21