HomeMy WebLinkAboutH-301 - HVAC ENLARGED UNIT PLANSTTT
T6/6 F50
6ø FCU-1 12/1014/6 F200
14/6 F190
14/6 F180
8ø
8ø
8ø
1
24/12 G620
2
3
3
3
3
EF-1
5
6
7
J -
36/8 8 9 10
4
4ø
6ø
14J-
36/8
6ø
FCU-1
30/8 G620
12/10
ø6
ø8ø8
ø8
EF-1
1
2
3
3
33
4
14/6 F190
F 14/6
190
14/6 F190
F 6/6
50 5
6
7
J-
36/6
7
8 9 10
4ø6øFCU-2
F 8/6
100
8/6 F100
8/6 F100 F 8/6
180
8/6 F180
F 6/6
50F6/6
50
ø8
ø8
ø6
ø6
12/108/6ø6
ø6
ø6 4øJ -
36/8
G 36/8
760
112
3
3
3 3 3
3
3
4
EF-1
EF-15
5
6
7
14
8 9 10
6ø6ø
6ø
G-
36/8
18/8
FCU-2
F 6/6
50
F 6/6
50
8/6 F180
F 8/6
50
F 8/6
100
F 8/6
150
F 8/6
180
4ø
ø8
ø8
10/10
ø6
10/10
ø6
ø8
ø8
ø6
EF-16ø6ø
EF-1
1
2
1
3
3
3
3
3
3
3
12
EF-15
5
5
J -
36/6 7
6
8 9 10
13
11
18166
Project:
Developer:
Sheet Number:
Engineer:
By:
Sheet Title:
CDG Number:
Last Revision Date:
Set Issue Date
Drawn By Checked By
Sheet Issue DateWINDSOR BUILDINGCarmel, IN 46032CONSTRUCTION
DOCUMENTS800 West Monon Green Blvd.H-301
HVAC ENLARGED UNIT
PLANS
08/31/202108/31/2021
THOMAS KENNEDY JOE BOLYARD
1/4" = 1'-0"
UNIT 'A1' HVAC ENLARGED PLAN108'4'2'
SHEET PLAN NOTES
1 TERMINATE EXHAUST DUCTWORK WITH WALL CAP LIKE GREENHECK MODEL
WC-6.
2 TERMINATE EXHAUST DUCTWORK WITH WALL CAP LIKE GREENHECK MODEL
WC-4.
3 PROVIDE CEILING RADIATION DAMPER AT ALL LOCATIONS WHERE GRILLES
PENETRATE A FIRE RATED CEILING.
4 PROVIDE DRYER BOX PER MANUFACTURER'S INSTRUCTIONS. MOUNT
BOTTOM OF DRYER BOX AT NOMINAL 6" ABOVE FINISHED FLOOR. SEAL
AROUND BOX PERIMETER. COORDINATE LOCATION WITH ARCHITECTURAL
PLANS. INSTALL LABEL SHOWING EQUIVALENT LENGTH OF INSTALLED DRYER
VENT (INCLUDING NUMBER OF ELBOWS) PER MECHANICAL CODE.
5 PROVIDE BATHROOM EXHAUST FAN EF-1 IN WALL USE ONLY SMOOTH RADIUS
ELBOWS (R/D = 1.5).
6 PROVIDE 7 DAY PROGRAMMABLE THERMOSTAT WITH THE TOP OF DEVICE 48"
ABOVE FINISHED FLOOR.
7 FURNISH AND INSTALL TRANSFER GRILLE 6" ABOVE TOP OF DOOR. SHEET
METAL TO BE INSTALLED THROUGH THE WALL. PAINT BLACK ANY STUDS
THAT INTERSECT.
8 PROVIDE FLEXIBLE CONNECTION TO FCU DISCHARGE BEFORE CONNECTION
TO SUPPLY DUCTWORK. PROVIDE FIRE DAMPER WHERE DUCT PENETRATES
RATED CEILING PARTITION.
9 PROVIDE TRAPPED 3/4" PLENUM RATED CPVC CONDENSATE DRAIN LINE AND
TERMINATE MINIMUM OF 2" ABOVE HUB-DRAIN LOCATED IN MECHANICAL
CLOSET. DO NOT BLOCK FILTER ACCESS.
10 ROUTE REFRIGERANT LINES UP TO ABOVE CEILING AND OVER TO EXTERIOR
WALL. ROUTE DOWN IN WALL TO 12" ABOVE GRADE, THEN OVER TO
CONDENSING UNIT SERVING THIS APARTMENT. SEE OVERALL MECHANICAL
PLANS FOR CONDENSING UNIT LOCATIONS. REFRIGERANT LINES SIZED PER
MANUFACTURER'S RECOMMENDATIONS.
11 PROVIDE 18"X18" CEILING ACCESS DOOR BELOW DRYER BOOSTER FAN
DBF-1.
12 PROVIDE DRYER BOX PER MANUFACTURER'S INSTRUCTIONS. MOUNT
BOTTOM OF DRYER BOX AT NOMINAL 6" ABOVE FINISHED FLOOR. SEAL
AROUND BOX PERIMETER. PROVIDE LINT TRAP EQUAL TO FANTECH DBLT4W.
COORDINATE LOCATION WITH ARCHITECTURAL PLANS. INSTALL LABEL
SHOWING LENGTH OF INSTALLED DRYER VENT (INLUDING NUMBER OF
WLBOWS) PER MECHANICAL CODE. INSTALL SECONDARY LINT TRAP IN
AIRSTREAM AT 7'-0" ABOVE FINISHED FLOOR.
13 PROVIDE RETURN GRILLE 6" ABOVE DOOR FRAME. TRANSITION USING 30°
REDUCER BEHIND. DUCTWORK ROUTES BELOW RATED ASSEMBLY AND
ABOVE DROP CEILING IN CLOSET.
14 PROVIDE RETURN GRILLE AND MOUNT HIGH ON WALL, TIGHT TO CEILING.
1/4" = 1'-0"
UNIT 'A2' HVAC ENLARGED PLAN2
0 8'4'2'
1/4" = 1'-0"
UNIT 'B1' HVAC ENLARGED PLAN3
0 8'4'2'
1/4" = 1'-0"
UNIT 'B2' HVAC ENLARGED PLAN408'4'2'
11700201
No.
STATE OFJOSEPHR.BO
L
Y
ARDPROFE
S
S
IONA L E N G INEERDATE SIGNED 08/31/21REGISTER
E
D
I
ND I A N A