HomeMy WebLinkAboutPacket - Renderings, Elevations, Sign DetailsLocation:
Drawing No:
Date:
Page No:
This is an original unpublished drawing created by First & Main Signs. It is
submitted for your personal use in conjunction with a project being planned
for you by First & Main Signs. It is not to be shown to anyone outside your
organization, nor is it to be used, reproduced, copied or exhibited in any fashion
without written permission from First & Main Signs.
Approved
Revise & Resubmit
Approved as Noted
CO Hatch
38 W. Main St.
Carmel, IN 46032
1) MG:11/12/21:Show spandrel, show blade sign from curb
Fix blade sign B to new stds (white returns, black mtg plate)
MG
19-0990-R01
10.31.2021
38 W. Main St.
Carmel, IN 46032
Prepared for:
CO Hatch
#19-0990-R01
Location:
Drawing No:
Date:
Page No:
This is an original unpublished drawing created by First & Main Signs. It is
submitted for your personal use in conjunction with a project being planned
for you by First & Main Signs. It is not to be shown to anyone outside your
organization, nor is it to be used, reproduced, copied or exhibited in any fashion
without written permission from First & Main Signs.
Approved
Revise & Resubmit
Approved as Noted
CO Hatch
38 W. Main St.
Carmel, IN 46032
1) MG:11/12/21:Show spandrel, show blade sign from curb
Fix blade sign B to new stds (white returns, black mtg plate)
MG
19-0990-R01
10.31.2021
SP1.00
A
B
Location:
Drawing No:
Date:
Page No:
This is an original unpublished drawing created by First & Main Signs. It is
submitted for your personal use in conjunction with a project being planned
for you by First & Main Signs. It is not to be shown to anyone outside your
organization, nor is it to be used, reproduced, copied or exhibited in any fashion
without written permission from First & Main Signs.
Approved
Revise & Resubmit
Approved as Noted
CO Hatch
38 W. Main St.
Carmel, IN 46032
1) MG:11/12/21:Show spandrel, show blade sign from curb
Fix blade sign B to new stds (white returns, black mtg plate)
MG
19-0990-R01
10.31.2021
ARTIST RENDERING
SCALE: NTS1
1.00
A
B
Location:
Drawing No:
Date:
Page No:
This is an original unpublished drawing created by First & Main Signs. It is
submitted for your personal use in conjunction with a project being planned
for you by First & Main Signs. It is not to be shown to anyone outside your
organization, nor is it to be used, reproduced, copied or exhibited in any fashion
without written permission from First & Main Signs.
Approved
Revise & Resubmit
Approved as Noted
CO Hatch
38 W. Main St.
Carmel, IN 46032
1) MG:11/12/21:Show spandrel, show blade sign from curb
Fix blade sign B to new stds (white returns, black mtg plate)
MG
19-0990-R01
10.31.2021
1.00
SOUTH ELEVATION (FRONT ENTRANCE)
SCALE: 1/4" = 1' - 0"1±5' - 6" OAH of Spandrel Area4' - 10"4' - 10"4' - 10"45' - 2” Frontage
A
B
44' - 3” OAL of Sprandrel Area
Location:
Drawing No:
Date:
Page No:
This is an original unpublished drawing created by First & Main Signs. It is
submitted for your personal use in conjunction with a project being planned
for you by First & Main Signs. It is not to be shown to anyone outside your
organization, nor is it to be used, reproduced, copied or exhibited in any fashion
without written permission from First & Main Signs.
Approved
Revise & Resubmit
Approved as Noted
CO Hatch
38 W. Main St.
Carmel, IN 46032
1) MG:11/12/21:Show spandrel, show blade sign from curb
Fix blade sign B to new stds (white returns, black mtg plate)
MG
19-0990-R01
10.31.2021
FACE-LIT CHANNEL LETTERS
SCALE: 1/2" = 1' - 0"A
ONE [1]REQUIRED -MANUFACTURE &INSTALL
SPECIFICATIONS
CHANNEL LETTERS
• 3/16” white acrylic faces with 1st surface 3M Dual-Color Film PTM PMS 2256C (Green)
Green @ Day, White @ Night
Apply 3M White (7725-10) opaque vinyl for center stripes for “CO”
• 1” black trim cap
• .040” aluminum returns, PTM PMS 2256C (satin finish)
• Internal LED illumination, white
• Remote power supply(s)
• Flush mount to fascia
13' - 10"
SIGN AREA = 53.02 SQ. FT.
END VIEW
3”
2.00
PMS 2256C (Green)3' - 10"3' - 10"3' - 10"1' - 5"1' - 5"1' - 5"5 ½"5 ½"5 ½"DAYTIME NIGHTTIME
Location:
Drawing No:
Date:
Page No:
This is an original unpublished drawing created by First & Main Signs. It is
submitted for your personal use in conjunction with a project being planned
for you by First & Main Signs. It is not to be shown to anyone outside your
organization, nor is it to be used, reproduced, copied or exhibited in any fashion
without written permission from First & Main Signs.
Approved
Revise & Resubmit
Approved as Noted
CO Hatch
38 W. Main St.
Carmel, IN 46032
1) MG:11/12/21:Show spandrel, show blade sign from curb
Fix blade sign B to new stds (white returns, black mtg plate)
MG
19-0990-R01
10.31.2021CHANNEL LETTER (LED Face-Lit) SECTION DETAIL
SCALE: 3" = 1' - 0"2
Metal studs
16” O.C. (typ)
LED enclosure,
waterproof box
with removable
cover
Cut-off switch
Primary electrical (120v)
provided by G.C. with
10’-0” leads
LED (12v) power
supply
U.L. LABELS REQUIRED
INSTALL IN ACCORDANCE W/
NATIONAL ELECTRIC CODES
ELECTRICAL ILLUMINATION REQUIREMENTS
NOTE: All primary electrical to sign location to be provided by others.
A dedicated circuit with NO shared neutrals and a ground returning to
the panel is required for installation.
This sign is intended to be installed in accordance with Article 600 or
the National Electrical Code and/or other applicable local codes. This
includes proper grounding and bonding of the sign.
All power supplies to be Ground-Fault Interrupted (GFI)
Signage to have a dedicated branch circuit, three (3) wires (Line,
Neutral and Ground)
Wire sizes to be a minimum of 12 Ga. THHN copper wire. Gauge of wire
is determined by the length of run and amperage as per NED Article
300
Voltage should read no more than 3 volts between ground and neutral
Conduit can not be used as ground path
Power to sign to be done by a electrical contractor or licensed
electrician
Ground wire must be continuous and go from sign to panel board
ground bus.
®ALL COMPONENTS TO BE APPROVED
1 Dedicated 20 Amp Circuit at 120 Volts
2.01
A
.040 aluminum returns (PTM PMS 2256C)
Zinc plated, panhead screws (painted black)
1” black trimcap
pop rivets
3/16” white acrylic face
with 1st surface 3M Dual-Color Film PTM PMS 2256C (Green)
Green @ Day, White @ Night
Paint interior with light enhancement paint
LED strip lighting, VHB mounted to back
.040 alum back
Secondary low voltage wiring
Conduit bushing
Liquid tight conduit
¼” Ø weeholes (min. 2 per letter) with
light baffles to prevent light leaks
Brick Fascia (To Be Verified)
Wedge anchors into brick fascia
3"
Location:
Drawing No:
Date:
Page No:
This is an original unpublished drawing created by First & Main Signs. It is
submitted for your personal use in conjunction with a project being planned
for you by First & Main Signs. It is not to be shown to anyone outside your
organization, nor is it to be used, reproduced, copied or exhibited in any fashion
without written permission from First & Main Signs.
Approved
Revise & Resubmit
Approved as Noted
CO Hatch
38 W. Main St.
Carmel, IN 46032
1) MG:11/12/21:Show spandrel, show blade sign from curb
Fix blade sign B to new stds (white returns, black mtg plate)
MG
19-0990-R01
10.31.20216”2½"
¼"¼"
NON-ILLUMINATED BLADE SIGN
SCALE: 1 1/2" = 1' - 0"B
ONE [1]REQUIRED -MANUFACTURE &INSTALL
SPECIFICATIONS
SIGN AREA = 3.14 SQ. FT.
• 1” x 1” aluminum c-channel frame with .080” aluminum clad faces painted black (satin finish)
• FACE - 3/4” acrylic, face and edges painted white (satin finish)
• Digitally printed wood grain on vinyl applied to what acrylic face, outside border to show-thru white.
• 1/4” acrylic FCOs, faces and edges painted white (satin finish), applied to face over wood grain digital print.
• 1” aluminum sq. tube vertical support covers painted black (satin finish) w/ internal threaded rod connection to sign and horizontal support
• 1½” aluminum sq. tube horizontal support painted black (satin finish)w/ access cover at top and capped end
• 1/4” aluminum mounting plate. Plate and exposed fasteners/hardware painted black (satin finish)
END VIEW
2' - 6½”2' - 0"2' - 0"2' - 0"4”2’ - 0”3"3"3"1½”
6”
3.008"8"8"3”3”3”1”1”1”TYPICAL ELEVATION
SCALE: 3/8" = 1' - 0"18’ - 0” AFF (TBV)Capped ends
Cover cut to
radius of cabinet
18¾” O.C.
Inlines to be 1st surface
3M Black (7725-12)
vinyl
2½”
45' - 2” Frontage
±13'-10”
Curb
2'-6½” OAL of Blade
Scale: 1/32” - 1’-0”
AERIAL VIEW
Location:
Drawing No:
Date:
Page No:
This is an original unpublished drawing created by First & Main Signs. It is
submitted for your personal use in conjunction with a project being planned
for you by First & Main Signs. It is not to be shown to anyone outside your
organization, nor is it to be used, reproduced, copied or exhibited in any fashion
without written permission from First & Main Signs.
Approved
Revise & Resubmit
Approved as Noted
CO Hatch
38 W. Main St.
Carmel, IN 46032
1) MG:11/12/21:Show spandrel, show blade sign from curb
Fix blade sign B to new stds (white returns, black mtg plate)
MG
19-0990-R01
10.31.20216”1"¾"¾"
¼"
¼"
1½”
6”
¼"
SECTION DETAIL
SCALE: 3" = 1' - 0"1B
6” x 6” x ¼” aluminum plate, painted black (satin finish)
Mounting bolts, pending survey of wall
1½” x 1½” aluminum square tube (horizontal support bar),
welded to mounting plate. Add access openings for threaded rods
into c-channel frame. Tube painted black (satin finish)
1” x 1” aluminum square tube (vertical arm (total 2)),
cover, painted black (satin finish)
1” x 1” aluminum c-channel frame. painted white (satin finish)
.080 aluminum cladding
¾” thick acrylic, painted white (satin finish)
Secure to aluminum face with Lords adhesive
¼” thick acrylic painted white (satin finish)
Wood grain digital print applied to 1st
surface of ¾” acrylic. White border of acrylic
to show-thru
Threaded rod
Rivnut
3.01