The URL can be used to link to this page

Home My WebLink AboutVWC CONV STORE14 A3.5 10-14-2021I I IREVISIONS:DRAWING COMPLETION DATE:4820 Buttonwood CrescentARCHITECT AIAGORDON CLARKIndianapolis, Indiana 46228Phone: 317 255-2546317 252-5573Fax: GClark4820@aol.comCONVENIENCE STORE / FOOD MARTVILLAGE OF WEST CLAYCARMEL, INDIANASOUTHWEST CORNER OFHARLESTON STREET AND TOWNE ROADOCTOBER 14, 2021 FOR PERMITTING AND CONSTRUCTIONNOTE: THIS COOLER SYSTEM SHALL BE A PRE-ENGINEERED UNIT FULLY OPERATIONAL. IT SHALL BE INSTALLED STRICTLY ACCORDING TO MANUFACTURER'S WRITTEN INSTRUCTIONS. INSTALLATION SHALL PREFERABLY BE BY THE MANUFACTURER'S SERVICE REPRESENTATIVES. THIS SHALL MEET ALL STATE AND LOCAL BUILING CODES. CONSULT ARCHITECT WITH ANY QUESTIONS OR UNUSUAL CONDITIONS ENCOUNTERED. THE BASIS OF DESIGN IS "U.S. COOLER COMPANY" 2"x6" REDWOOD (THERMAL-BREAK; AROUND PERIMETER AND DIVIDING WALLS) VINYL SCREEDING OR 2"x2" ALUM. ANGLE 6 MIL. VAPOR BARRIER TAPE ALL JOINTS COOLER WALL PANEL 4" CONCRETE SLAB 4" COMPACTED FILL 4" INSULATION OR COOLER FLOOR PROVIDED BY COOLER MFGR. TYPICAL EXTERIOR WALL SEE OTHER DETAILS SCALE: 1" = 1'-0" 1 SECTION THRU COOLER OPEN-WEB STEEL JOISTS 24" O.C. SEE OTHER DETAILS AND SPECIFICATIONS UNISTRUT HANGERS FOR ALL BULKHEADS 3 5/8" STEEL STUDS 24" O.C. 5/8" DRYWALL SURFACE SUSPENDED ACOUSTIC CEILING AT 10'-0" AFF 3 5/8" STEEL STUDS 24" O.C. 5/8" DRYWALL SURFACE TYPICAL BULKHEAD WALK-IN COOLER SPECIFICATIONS: Refrigeration A) Walk-in Refrigerator and Freezer Construction 1) General: Each panel shall consist of inner and outer metal skins, a 4” insulation core, and be equipped with cam-action locking devices. The locking devices shall be operable from inside the walk-in. Construction shall be as approved by the NSF International and shall bear the NSF® Seal of Approval. All panels shall be connected to one another by placing the tongue of the insulation core of one panel into the groove of the core insulation of the adjacent panel. The resultant tongue and groove joint shall be sealed at both sides by double barreled NSF® approved gaskets. In order to avoid future swelling and mold formation, no wood shall be permitted in the manufacture of the tongue and groove panel profile. (a) Wall Panels: Panel insulation shall be 4” thick, high quality, extruded polystyrene or foamed-in-place polyurethane, modular panels joined by not less than three (3) cam-lock devices; gasket to seal between panels; R-28 or greater for refrigerators and R-32 or greater for freezers. (b) Ceiling: Panel insulation shall be 4” thick, high quality, extruded polystyrene or foamed-in-place polyurethane, modular panels joined by not less than three (3) cam-lock devices; gasket to seal between panels; R-28 or greater for refrigerators and R-32 or greater for freezers. (a) Sloped Roof Package: When specified. For use on walk-ins installed outdoors. May be required at certain snow loads. In order to form a sloped roof profile, suitable quantities of sloped foam shall be provided. The foam shall be cut in a manner that upon installation, a ¼”:1’ slope is obtained. The membrane roof shall be increased in size appropriately, in order to provide the additional material required to properly cover the resultant profile. (b) Roof panels shall be rated to withstand up to 90 mph winds. (c) Finishes: (i) Exterior Finishes: (a) 26 gauge tan stucco embossed galvanized steel (ii) Interior Finishes (a) Wall Panels: i. 26 gauge stucco embossed galvalume (b) Ceiling Panels: i. 26 gauge stucco embossed galvalume (c) Floors: i. 22 gauge smooth stainless steel (d) Panel Dimensions: As required for layout. 2) Doors: R-25 or greater for refrigerators; R-32 or greater for freezers. Door shall be flush mounted, positioned and hinged; provided with suitable sweep and magnetic gaskets, door closer, one pre-wired vapor proof light fixture, light switch with pilot light, dial thermometer, manual internal lock override, chrome plated cam lift hinges, chrome plated door latches with strike. (i) Outdoor Units: Doors on outdoor walk-ins shall have weather protected light switch and door drip cap. (ii) Freezer Doors: Freezer doors shall be identical to cooler doors, but with the addition of UL approved heater wire on all four sides. Freezer doors shall include a heated pressure relief port in the adjacent panel. (b) Thermometer: See item specification for thermometers required for this project: Thermometer installed flush-mount on hinge side of door panel. (c) Digital Thermometer (optional): 3” round digital thermometer with probe, installed flush-mount on hinge side of door panel. (d) Digital Thermometer with Alarm (optional): Specifications available. 3) Pressure Relief Port: Provide heated relief port in freezers. 4) Lights: Per owner’s requirements. (a) Fluorescent: 4’ vapor proof; optional per customer specification. (b) Incandescent: Single bulb, vapor proof; installed on door panel. (c) LED: Single bulb or 4’ vapor proof; optional per customer specification. 5) Installation: Dealer to install walk-in units. (a) Drawings and Instructions: Manufacturer shall supply a set of installation instructions and lay-out drawing. All panels shall have panel identification corresponding with the lay-out drawing to facilitate rapid and accurate field erection. B) Refrigeration System: Complete operating system consisting of a condensing unit and a evaporator coil. 1) Condensing Unit: General: Condenser fan motors of under 1 h.p. must use electronically commutated (EC) motors or permanent split capacitator-type (PSP) motors; splash lubrication system using Mobil EAL Arctic 22 polyester synthetic refrigeration oil; oil sight glass; removable oil drain plug; label indicating oil used; (a) high/low pressure control; suction line filter; suction and discharge service valves and copper/brass vibration isolators; receiver with fusible plug or relief valve; liquid line shut-off valve; sight glass; molecular sieve filter dryer; main power supply fused disconnect switch (b) Outdoor: Weather proof housing; crank case heater and low ambient temperature controls required to insure proper and efficient operation; fan cycling controls where ambient temperatures do not fall below -15°; head master valve and oversized, heated, insulated receiver and lines where ambient temperatures fall below -15°F. 2) Evaporator Coil: Forced convection style; match to condensing unit and suspend with air discharged parallel to the ceiling; lifetime sealed motors with inherent motor protection; evaporator fan motors of under 1 hp and less than 460 volts must use electronically commutated (EC) motors; enclose coil section and fans within aluminum housing (a) Refrigerator: Air defrost (b) Freezer and Low Temperature Refrigerator: Electric heater and controls for positive automatic defrost (c) Installation: Hang using plastic or nylon fasteners; spread coil weight evenly over ceiling panels; support long span ceiling panels as required. STEEL FINAL DESIGN SHALL BE ON A DESIGN/BUILD BASIS 4"x4"x3/8" ANGLE FOR SHEAR TRANSFER AND STEEL DECK SUPPORT ANGLE SHALL FOLLOW ROOF SLOPEBOND BEAM HEIGHT VARIES WITH ROOF SLOPE HORIZONTAL REINFORCING EVERY 2'-0" O.C. 2" AIR SPACE 4" CONCRETE FLOOR SLAB SEE SPECS. AND OTHER DETAILS TOP OF MASONRY 16'-0" AFF TOP OF INTERMEDIATE BOND BEAM 10'-0" AFFTO DO A3.5 A3.5 THIS IS TYPICAL ON ENTIRE PERIMETER OF BUILDING MASONRY