Loading...
HomeMy WebLinkAboutID001BSCOPE OF WORK SJL DESIGN GROUP'S INTERIOR DESIGN SCOPE INCLUDES THE COMMON AREAS AS FOLLOWS: LOBBY CORRIDORS LEASING FITNESS ROOM OFFICE PUBLIC RESTROOMS WORK ROOM BIKE & STORAGE CO-WORK MAIL & PARCEL ROOM CLUB ELEVATOR LOBBIES SPORTS SIMULATOR PET WASH SHEET INDEX DRAWING ISSUESPOWER/DATA NOTES & SPECIFICATIONS 1. PRIOR TO RECEIVING FINISHES VERIFY SURFACES TO RECEIVE FINISHES ARE CLEAN TRUE AND FREE OF IRREGULARITIES. DO NOT PROCEED WITH FINISH WORK UNTIL UNSATISFACTORY CONDITIONS HAVE BEEN CORRECTED. 2. WOOD DOORS, STAIN GRADE ARCHITECTURAL MILLWORK AND CABINETRY SHALL BE SHOP FINISHED. 3. PRIOR TO PURCHASE OR INSTALLATION OF ANY FINISH, SUBMIT (2) SAMPLES TO SJL DESIGN GROUP FOR REVIEW. ALLOW TIME FOR SUBMITTAL REVIEW AND RESUBMITTALS IF REQUIRED. 4. WHERE DEMOLITION AFFECTS WALLS, CEILINGS, CARPET, ETC. THAT IS TO REMAIN PATCH, REPAIR AND REFINISH TO PROVIDE A "LIKE NEW" APPEARANCE. 5. ALL NEW AND EXISTING FINISHES SCHEDULED TO REMAIN, SHALL BE PROTECTED DURING CONSTRUCTION, ANY DAMAGE SHALL BE REPAIRED BY CONTRACTOR INVOLVED AT HIS COST, WITH NO COST TO OWNER. 6. PRIOR TO INSTALLATION OF NEW FLOORING, REMOVE ALL FOREIGN MATTERS SUCH AS GREASE, WAX, OIL, DIRT, ETC. FILL CRACKS, HOLES AND DEPRESSIONS, AND GRIND ANY PROTRUDING OBJECTS SMOOTH WITH THE FLOOR SURFACE. 7. THE LONGEST LEAD TIME PRODUCTS ARE TO BE ORDERED FIRST. NO SUBSTITUTES WILL BE ACCEPTED W/O APPROVAL OF SJL DESIGN GROUP. 8. ALL FLOORING TRANSITIONS TO OCCUR @ CENTER OF DOORS, UNLESS OTHERWISE NOTED. REFER TO FLOOR TRANSITION DETAILS. 9. CONTRACTOR TO PROVIDE 5% ATTIC STOCK FOR ALL FINISHES. 10. ALL FINISHES SHALL MEET OR EXCEED LOCAL CODES. 11. ALL NEWLY INSTALLED FLOORING FINISHES SHALL BE PROTECTED FROM DAMAGE UNTIL CONSTRUCTION IS COMPLETED. CARPET 12. CARPET INSTALLER TO PROVIDE SEAMING DIAGRAM TO SJL DESIGN GROUP FOR REVIEW AND APPROVAL PRIOR TO ORDERING CARPET. DO NOT CROSS SEAM, OR SUBSTITUTE MANUFACTURERS. 13. ALL SEAMS SHALL BE SECURED BY MANUFACTURER'S RECOMMENDATIONS. 14. INSTALL CARPET FLAT, LEVEL AND SECURE, USING METHOD NOTED ON FINISH PLAN AND MANUFACTURER'S RECOMMENDATIONS. 15. ALL FLOOR MONUMENTS OR DEVICES SHALL BE INSTALLED FOLLOWING CARPET INSTALLATION. CARPET INSTALLER TO COORDINATE CUTTING OF CARPET FOR FLOOR OUTLETS WITH ELECTRICAL CONTRACTOR. 16. ALL SIZABLE PIECES OF UNUSED CARPET IN ADDITION TO CARPET ORDERED FOR ATTIC STOCK, IS TO BE LEFT ON SITE FOLLOWING INSTALLATION, OR STORED OFF SITE PER OWNER'S INSTRUCTIONS. CERAMIC TILE 17. CERAMIC TILE SHALL BE INSTALLED IN STRICT ACCORDANCE WITH THE REFERENCE STANDARDS PUBLISHED IN THE TILE COUNCIL OF AMERICA'S "HANDBOOK FOR CERAMIC TILE INSTALLATION" AND WITH MANUFACTURER'S RECOMMENDED GUIDELINES. 18. OTHER TILE TYPES: GLASS, PORCELAIN, ETC. SHALL COMPLY WITH THE MANUFACTURER'S/DISTRIBUTOR'S INSTALLATION RECOMMENDATIONS. WALL COVERING 19. ALL WALL COVERING PRIMERS, SEALERS, ADHESIVES, SIZING AND INSTALLATION METHODS SHALL BE PER WALL COVERING MANUFACTURER'S RECOMMENDATIONS. 20. INSTALL WALL COVERING TO BE SECURE AND FLAT, WITHOUT WRINKLES, GAPS OR OVERLAPS. SEAMS SHALL BE TIGHT AND SECURE. CLEAN WALL COVERING TO BE FREE OF DIRT AND GLUE. 21. WALL COVERING SEAMS SHOULD BE NO CLOSER THAN 6 INCHES FROM OUTSIDE CORNERS AND 3 INCHES FROM INSIDE CORNERS. HORIZONTAL SEAMS ARE UNACCEPTABLE UNLESS OTHERWISE NOTED. ALL SEAMS SHALL BE VERTICAL AND PLUMB, WITH PATTERNS MATCHED TO GREATEST EXTENT POSSIBLE WHERE PATTERNS OCCUR. PAINT 22. COMPLY WITH APPLICABLE FEDERAL, STATE AND LOCAL REGULATIONS GOVERNING THE USE OF PAINT MATERIALS. 23. COMPLY WITH MANUF,RECOMMENDATIONS FOR ENVIRONMENTAL CONDITIONS UNDER WHICH COATINGS & COATING SYSTEMS CAN BE APPLIED. 24. PROTECT FLOORS AND ALL ADJACENT SURFACES FROM PAINT SMEARS, SPATTERS AND DROPPINGS. USE DROP CLOTHS TO PROTECT FLOORS AND ITEMS NOT TO BE PAINTED. MASK OFF AREAS WHERE REQUIRED. 25. CLEAN SURFACES FREE OF DUST, DIRT, OIL, GREASE AND OTHER FOREIGN MATTER PRIOR TO APPLICATION OF THE PRIME COAT. 26. REPAIR ALL VOIDS, NICKS, CRACK, DENTS, ETC. WITH SUITABLE PATCHING MATERIAL AND FINISH FLUSH TO ADJACENT SURFACE. 27. DO NOT APPLY FINISHES IN AREAS WHERE DUST IS BEING GENERATED, OR WHEN ROOM TEMPERATURE IS BELOW 50 DEGREES F. 28. ENSURE THAT HARDWARE, COVER PLATES, AND SIMILAR ITEMS ARE REMOVED PRIOR TO PAINTING, AND REPLACE ONLY WHEN PAINT FINISHES ARE THOROUGHLY DRY. 29. UNLESS NOTED OTHERWISE, PROVIDE MINIMUM 2-COAT SYSTEM AS SPECIFIED FOR EACH NEW SURFACE. FOR EXISTING SURFACES, APPLY NUMBER OF COATS TO INSURE COMPLETE COVERAGE OF PREVIOUS COLOR AND SURFACE REPAIRS AND/ OR PATCHING. REFER TO FINISH PLAN FOR COLORS AND SHEENS 1 PRIMER/2-3 FINISH COATS PER MANUFACTURER'S RECOMMENDATIONS. 30. ALLOW EACH COAT TO THOROUGHLY DRY BEFORE ADDITIONAL APPLICATIONS. 31. EMPLOY COATS AND UNDERCOATS FOR ALL TYPES OF FINISHES IN STRICT ACCORDANCE WITH RECOMMENDATIONS OF THE PAINT MANUFACTURER. ALL UNDERCOATS SHALL BE TINTED TO APPROXIMATE THE FINISH COLOR. 32. APPLY MATERIAL EVENLY BY BRUSH, ROLLER OR SPRAY. SURFACE IMPERFECTIONS WILL NOT BE ACCEPTABLE. ALL DECORATIVE PAINTING TO BE APPROVED BY SJL DESIGN GROUP. 33. SAND AND DUST BETWEEN COATS TO REMOVE DEFECTS VISIBLE TO THE NAKED EYE FROM A DISTANCE OF FIVE FEET. 34. IN AREAS OF HIGH HUMIDITY, SUCH AS ROOMS WITH BATHTUBS AND SHOWERS ADD AN APPROVED FUNGICIDE TO PAINTS. 35. PAINT VISIBLE DUCT SURFACES BEHIND VENTS, REGISTERS, AND GRILLS WITH FLAT BLACK INTERIOR PAINT. 36. LEAVE PAINT STORAGE SPACES IN A CLEAN AND FINISHED CONDITION. ALL EXTRA PAINT TO BE LEFT AT JOB SITE IN TIGHTLY SEALED CONTAINERS CLEARLY MARKED WITH CONTENTS AND LOCATION WHERE USED. 37. FINISH IN SEMI-GLOSS; SHELVING, ELECTRIC PANELS, ACCESS DOORS, CONDUIT, PIPES, DUCTS, GRILLES, AND ITEMS OF SIMILAR NATURE TO MATCH THE ADJACENT WALL AND CEILING PAINT COLOR, UNLESS PRE-FINISHED IN FINAL INTENDED COLOR, OR AS DIRECTED. 38. USE OIL-BASED SEMI-GLOSS FOR METAL DOOR JAMBS AND DOORS WHEN APPLICABLE. 39. WHEN PAINTING OVER WALL COVERING, MAKE REPAIRS TO WALL COVERING PRIOR TO PAINTING TO INSURE THAT IT IS SECURELY ADHERED TO WALL. 40. ALL PAINT TO MATCH SHERWIN WILLIAMS. WALLS & CEILINGS: EGG SHELL FINISH, TRIM: SEMI-GLOSS FINISH. FINISH NOTES MILLWORK NOTES 1. FURNISH AND INSTALL CUSTOM MILLWORK AS SHOWN ON PLANS AND DETAILS. 2. THE CUSTOM GRADE STANDARDS OF THE ARCHITECTURAL WOODWORK INSTITUTE (AWI) WILL BE USED TO ESTABLISH EQUALITY OF WORKMANSHIP AND REQUIRED TOLERANCES, HOWEVER, (AWI) CERTIFICATION WILL NOT BE REQUIRED. 3. PROVIDE SHOP DRAWINGS FOR REVIEW AND APPROVAL PRIOR TO FABRICATION. SHOW DIMENSIONED PLANS, ELEVATIONS, SECTIONS, DETAILS AND HARDWARE SPECIFICATIONS PER UNIT, INCLUDING INSTALLATION. FABRICATOR IS RESPONSIBLE FOR COORDINATING WORK WITH OTHER DISCIPLINES. 4. PROVIDE TWO 6" X 6" SAMPLES OF EACH FINISH PRIOR TO FABRICATION. 5. INSTALL THE WORK PLUMB, LEVEL TRUE AND STRAIGHT WITH NO DISTORTIONS. ATTACH UNIT SECURELY TO WALLS, AND ATTACH COUNTERTOPS SECURELY TO BASE CABINETS, MAKE CUTS FOR HARDWARE AND EQUIPMENT NEAT AND TRUE. INSTALL AND ADJUST HARDWARE, DOORS AND SHELVING TO OPERATE IN A SMOOTH MANNER WITHOUT BINDING, SCRIBE AND FIT ALL WORK AS REQUIRED. 6. VERIFY QUANTITY, SIZE AND LOCATION OF ALL ITEMS AFFECTING WORK INCLUDING, BUT NOT LIMITED TO, PLUMBING FIXTURES, ELECTRICAL RECEPTACLES, CONDUIT, APPLIANCES AND EQUIPMENT BEING PROVIDED BY OTHERS, PRIOR TO FABRICATION. ADVISE SJL DESIGN GROUP OF ANY ITEMS IN CONFLICT WITH MILLWORK PRIOR TO FABRICATION. 7. CONTRACTOR TO COORDINATE LOCATIONS OF ELECTRICAL, TELEPHONE AND DATA OUTLETS MOUNTED ABOVE MILLWORK COUNTERTOPS, UNDER WALL CABINETS AND WITHIN MILLWORK CABINETS WITH FABRICATOR. REFLECTED CEILING NOTES ELEVATION REFERENCE KEY SECTION KEY DETAIL TAG FULL HEIGHT WALL PARTIAL HEIGHT WALL PLYWOOD SUBSTRATE FINISH GRADE WOOD STOCK PLASTIC LAMINATE/ WD VENEER ON SUBSTRATE GYPSUM BOARD METAL FRAMING WOOD FRAMING WOOD BLOCKING DUPLEX RECEPTACLE OUTLET 20A, 125V, +18" GROUND FAULT INTERRUPT OUTLET DUPLEX FLOOR RECEPTACLE OUTLET 20A, 125V DEDICATED VOICE/DATA LINE VOICE /DATA FLOOR RECEPTACLE OUTLET TV DESIGNATION CABLE OUTLET CABLE FLOOR RECEPTACLE OUTLET FRESH WATER LINE WALL MOUNTED FIXTURE J-BOX FOR PENDANT OR ACCENT FIXTURE RECESSED CAN SMALL APERTURE RECESSED CAN SPECIALTY LIGHTING STANDARD WALL WASHER STANDARD SURFACE MOUNTED FIXTURE CEILING FAN WORKING POINT/ STARTING POINT GAS LINE GRAPHICS LEGEND ID-X.X/01 ID-X.X/01 ID-X.X/01 A.F.F. NOTE A.F.F. GFI TV NOTE A.F.F. NOTE J 1. ALL LIGHT SWITCHES SHALL BE LOCATED 6" FROM LATCH SIDE OF DOOR FRAME, UNLESS NOTED OTHERWISE. SWITCH HEIGHT SHALL CONFORM TO ADA STANDARDS, REFER TO ARCHITECTURAL AND ELECTRICAL DRAWINGS. 2. USE HIGH VOLTAGE DIMMERS AS REQUIRED WHEN SPECIFIED. 3. ALL ELECTRICAL SYSTEMS, DEVICES AND RELATED ITEMS SHALL BE TESTED. ENSURE PROPER OPERATION OF ALL ITEMS OR SYSTEMS BEFORE COMPLETION OF THE PROJECT. 4. UPON COMPLETION OF THE INSTALLATION OF ALL ELECTRICAL BOXES PRIOR TO WIRING AND DRYWALL CLOSE-IN, A SCHEDULED WALK THROUGH SHALL BE COORDINATED TO REVIEW LOCATIONS OF ALL THERMOSTATS, TELE/DATA, LIGHTING AND ELECTRICAL. RECORD DOCUMENT (AS BUILTS) DRAWINGS TO BE PROVIDED AT COMPLETION OF PROJECT. 5. ALL WORK SHALL CONFORM TO ALL APPLICABLE BUILDING CODES. 6. ALL MATERIALS SHALL BE U.L. LISTED. WHEN SUCH LISTINGS EXIST AND ALL WORK AND MATERIALS SHALL CONFORM WITH ALL CODES REGULATIONS AND LAWS IN FORCE, AND THE ELECTRICAL SPECIFICATIONS. 7. FIELD VERIFY EXISTING CONDITIONS. VERIFY LOCATION OF ALL OUTLETS IN RELATION TO MECHANICAL, STRUCTURAL AND PLUMBING ELEMENTS. 8. NEW OUTLET DEVICES SHALL BE MOUNTED AT 18" A.F.F. UNLESS NOTED OTHERWISE. DO NOT MATCH EXISTING OUTLET HEIGHTS THAT DO NOT COMPLY WITH THIS REQUIREMENT. 9. ANY ADDITIONAL OUTLETS REQUIRED BY CODE ARE THE RESPONSIBILITY OF THE CONTRACTOR. CONTRACTOR SHALL NOTIFY SJL DESIGN GROUP OF ANY ADDITIONALLY REQUIRED OUTLETS AND SHALL BE COORDINATED PRIOR TO INSTALLATION. 10. DEVICES ARE SHOWN FOR LOCATION ONLY. REFER TO ELECTRICAL SPECIFICATIONS FOR ALL SPECIFIC REQUIREMENTS, CIRCUITING, ETC. IN CASE OF CONFLICT BETWEEN INTERIOR PLANS AND ELECTRICAL PLANS. CLARIFICATION SHALL BE REQUESTED IN WRITING PRIOR TO INSTALLATION. 11. REFER TO MECHANICAL AND ELECTRICAL DRAWINGS FOR ADDITIONAL NOTES AND INFORMATION. NOTIFY SJL DESIGN GROUP OF ANY CONFLICTS WITH DESIGN INTENT PRIOR TO CONSTRUCTION. 12. PROVIDE CIRCUITING AS REQUIRED OR AS NOTED IN ELECTRICAL DRAWINGS. 13. DIMENSIONS NOTED ARE TO CENTERLINE OF THE OUTLET AND/OR SWITCH (INCLUDING CLUSTERS) U.N.O. 14. ALL FLOOR CORE LOCATIONS TO BE FIELD LOCATED AND VERIFIED WITH SJL DESIGN GROUP. 15. FOR NEW DEVICES OCCURRING IN FIRE RESISTANT WALL CONSTRUCTION, REFER TO ARCHITECTURAL AND ELECTRICAL FOR INSTALLATION REQUIREMENTS. FOR VOICE AND TELE/DATA LOCATIONS, REF. GRAPHIC LEGEND, CONTRACTOR SHALL REFER TO ELECTRICAL FOR INSTALLATION REQUIREMENTS. 16. STANDARD WALL OUTLETS TO BE INSTALLED VERTICALLY, UNLESS NOTED OTHERWISE. 17. COVER PLATES SHALL BE ONE PIECE TYPE UNLESS NOTED OTHERWISE. 18. THE STYLE AND FINISH OF ALL ELECTRICAL COVER PLATES SHALL BE VERIFIED WITH SJL DESIGN GROUP; FOR SPECIFIC COLOR AND DESIGN REFER TO ID-3.0'S & 5.0'S FOR ADDITIONAL INFORMATION IN SHEET NOTES. 19. LOCATION OF REMOTE POWER PANELS, DISCONNECT SWITCHES, SPECIAL PANELS, THERMOSTATS, SWITCHES, ALARMS OR ANY OTHER DEVICES WHICH ARE EXPOSED TO VIEW AND NOT INDICATED ON DRAWINGS SHALL BE VERIFIED WITH SJL DESIGN GROUP. 20. ALL EQUIPMENT MOUNTING REQUIREMENTS AND POWER SPECIFICATIONS SHALL BE VERIFIED PRIOR TO INSTALLATION. CONTACT SJL DESIGN GROUP. WHERE CONFLICTS OCCUR. 21. ALL EQUIPMENT REQUIRING DEDICATED CIRCUITS SHALL BE VERIFIED BY CONTRACTOR PRIOR TO INSTALLATION. 22. ALL ISOLATED GROUND COMPUTER CIRCUIT OUTLETS SHALL BE AN ORANGE COLORED RECEPTACLE. 23. ALL POWER AND TELE/DATA OUTLETS ARE TO COORDINATED TO MATCH FLUSH WITH NEW FLOOR FINISHES. 24. ELECTRONIC OR MAGNETIC DIMMERS ARE TO BE VERIFIED BY ELECTRICIAN AS TO COMPATIBILITY ON LOW VOLTAGE FIXTURES. 25. ALL OUTLETS ON SPECIALTY FINISH WALLS TO BE WOOD OR PAINT GRADE PLASTIC PAINTED TO MATCH SPECIALTY FINISH. 26. ELECTRICAL SWITCH PLATES ONLY: TO BE RECTANGULAR PLASTIC PAINTED TO MATCH TRIM, ALL OTHER PLATES TO BE PLASTIC- COLOR WHITE U.N.O. ALL ELECTRICAL OUTLETS TO BE POSITIONED ACCORDING TO ELECTRICAL PLAN AND AT A MAXIMUM OF 18" A.F.F. ALL SWITCH PLATES IN RESTROOMS TO BE INSTALLED WITH TOP AT 44" A.F.F. U.N.O. PAINTED TO MATCH WALL. ALL SWITCHES, ALARMS, SPEAKERS AND THERMOSTATS TO BE POSITIONED TO SIDE OF WALLS. NOT IN THE MIDDLE OF ANY WALL. 27. MEP TO COORDINATE POWER FOR ALL APPLIANCES AND ELECTRICAL EQUIPMENT PER MANUFACTURERS RECOMMENDED SPECS. GENERAL INTERIOR NOTES 1. LIGHT FIXTURES AND OTHER ITEMS SCHEDULED ON THE DRAWINGS SHALL BE LOCATED PER REFLECTED CEILING PLAN. THE GENERAL, MECHANICAL, AND ELECTRICAL CONTRACTORS SHALL USE EXTREME CARE IN COORDINATING THEIR WORK TO FIT THE PATTERN SHOWN ON THE REFLECTED CEILING PLAN. IF CONFLICT OCCURS BETWEEN MECHANICAL AND COORDINATION OF LIGHTING FIXTURES ABOVE CEILING, NOTIFY SJL DESIGN GROUP. 2. GANG ALL SWITCHES. 3. ELECTRICAL CONTRACTOR TO DETERMINE APPROPRIATE VOLTAGE FOR ALL FIXTURES PRIOR TO ORDERING 4. ELECTRICIAN TO SUPPLY LAMPS FOR ALL FIXTURES, INCLUDING FIXTURES SUPPLIED BY SJL DESIGN GROUP. 5. DO NOT USE HIGH VOLTAGE DIMMERS UNLESS NOTED OTHERWISE. 6. REFER TO REFLECTED CEILING PLAN FOR PREFERRED LOCATIONS OF HVAC SUPPLY AND RETURN GRILLS 7. REFER TO REFLECTED CEILING PLANS FOR PREFERRED LIGHTING LOCATIONS. ALL LIGHTING TO BE VERIFIED AND CALCUALTED BY MEP ENGINEER 8. HVAC DIFFUSERS AND RETURN GRILLS TO BE PAINTED TO MATCH ADJACENT SURFACE , UNLESS OTHERWISE NOTED 1. SCALE INDICATED ON DRAWING SHEET IS BASED ON FULL SIZE CONSTRUCTION DOCUMENTS. REPRODUCTIONS AND HALF SIZE SETS MAY NOT BE TO SCALE. ACTUAL SCALE OF DRAWINGS SHOULD BE VERIFIED WITH DIMENSIONS STATED IN DRAWINGS. 2. WHERE CONFLICTS OCCUR WITH ARCHITECTURAL OR CONSULTANT DRAWINGS CONFER WITH ARCHITECT OF RECORD FOR COORDINATION BEFORE PROCEEDING. 3. REFER TO ARCHITECTURALS FOR COLUMN GRID DIMENSIONS. 4. NO SLAB DEPRESSIONS REQUIRED AS A RESULT OF FLOORING MATERIAL SPECIFIED BY DESIGNERS. 5. LEGEND NOTES 1. REFER TO MEP PLANS FOR GENERAL POWER AND DATA; ID PLANS INDICATE ALL SPECIALTY POWER AND UTILITY LOCATIONS. 2. DATA AND ELECTRICAL IN ALL AREAS AT 18" A.F.F. UNLESS NOTED OTHERWISE. 3. REFER TO SPECIALTY POWER PLAN FOR A.F.F. HEIGHT OF JBOX FOR TVS. 4. REFER TO MEP DRAWINGS FOR LOCATION OF LIFE SAFETY DEVICES SUCH AS EXIT SIGNS, STROBES ETC.VENTS AND SPEAKERS TO MATCH WALLS AND CEILINGS. 5. VENTS AND SPEAKERS TO MATCH WALLS AND CEILINGS GENERAL INTERIOR ACCESSIBLE NOTES 1. FINISH FLOOR ELEVATIONS MAY VARY. PLEASE VERIFY WITH ARCHITECTURAL BUILDING SECTIONS FOR EXTENT AND ANGLE OF SLOPE. 2. ALL WALL MOUNTED TV'S TO PROJECT A MAX. OF 4" FROM FINISH FACE OF WALL. IF WALL MOUNTED TV'S PROJECT MORE THAN 4" FROM FINISH FACE OF WALL A CANE DETECTION DEVICE WILL BE REQUIRED. 3. ALL WALL MOUNTED ARTWORK TO PROJECT A MAX. OF 4" FROM FINISH FACE OF WALL OR BE MOUNTED 80" MIN. A.F.F. IF WALL MOUNTED ARTWORK MOUNTED BELOW 80" A.F.F. PROJECTS MORE THAN 4" FROM FINISH FACE OF WALL A CANE DETECTION DEVICE WILL BE REQUIRED. 4. FIREPLACE CONTROLS MUST BE MIN. 15" A.F.F. AND MAX. 48" A.F.F. AND NOT REQUIRE TIGHT GRASPING, PINCHING, OR TWISTING OF THE WRIST. ID-0.00B COVER SHEET - BLDG B ID-0.01B PROJECT STANDARDS AND SHEET INDEX - BLDG B ID-0.02 GENERAL CONSTRUCTION NOTES ID-0.03 FLOOR TRANSITION DETAILS ID-0.04.1 FINISH SCHEDULES ID-0.04.2 FINISH SCHEDULES ID-0.04.3 UNIT FINISH SCHEDULES ID-0.05 TRIM, DOOR, & WINDOW SCHEDULES ID-1.00B KEY PLAN - BLDG B - LVL 1 ID-1.01B KEY PLAN - BLDG B - LVL 2 ID-1.10B FLOOR PLANS - BLDG B - LVL 1 AMENITIES ID-1.11B FLOOR PLAN - BLDG B - LVL 1 CORRIDOR ID-1.12B FLOOR PLAN - BLDG B - LVL 3 TYP CORRIDOR ID-2.10B FINISH PLANS - BLDG B - LVL 1 AMENITIES ID-2.11B FINISH PLAN - BLDG B - LVL 1 CORRIDOR ID-2.12B FINISH PLAN - BLDG B - LVL 3 TYP CORRIDOR ID-3.10B REFLECTED CEILING PLANS - BLDG B - LVL 1 AMENITIES ID-3.10.1B REFLECTED CEILING PLANS DIMS - BLDG B - LVL 1 AMENITIES ID-3.11B REFLECTING CEILING PLAN - BLDG B - LVL 1 CORRIDOR ID-3.12B REFLECTED CEILING PLAN - BLDG B - LVL 3 TYP CORRIDOR ID-4.10B FURNITURE PLANS - BLDG B - LVL 1 AMENITIES ID-5.10B SPECIALTY POWER PLANS - BLDG B - LVL 1 AMENITIES ID-6.00B INTERIOR ELEVATIONS - BLDG B ID-6.01B INTERIOR ELEVATIONS - BLDG B ID-7.00B DETAILS & SECTIONS - BLDG B ID-7.01B DETAILS & SECTIONS - BLDG B ID-8.00 ELEVATOR CAB FINISHES LEGEND: ISSUED NOT ISSUED VOID 06.16.2021PERMIT SET08.20.2021IFC SETID-0.01B Project Standards Sheet Index N.T.S. CLIENT / DEVELOPER: PROJECT CONTACTS: PROJECT NAME: ISSUE LOG: SHEET NUMBER: DRAWING NAME: THE INTERIOR DESIGN PLANS AND SPECIFICATIONS ISSUED FOR THIS PROJECT HAVE BEEN PREPARED BY SJL DESIGN GROUP (SJL) FROM DATA PROVIDED BY THE REPRESENTATIVE OF THE CLIENT. THE COMPLETENESS AND ACCURACY OF THIS DATA HAS BEEN RELIED UPON BY SJL. INTERIOR AND PRODUCT DESIGNS ARE SUBJECT TO MODIFICATIONS OR CHANGES DUE TO FIELD VERIFICATIONS, EXISTING OR OTHER CONDITIONS AND BUILDING CODE REQUIREMENTS. THE DEVELOPER/CLIENT SHALL BE RESPONSIBLE FOR OBTAINING ALL REQUIRED PERMITS FOR THE PROJECT AND FOR COMPLIANCE WITH ALL LOCAL, STATE AND FEDERAL CODES. IN THE EVENT THE PLANS AND/OR SPECIFICATIONS ARE REQUIRED TO BE SEALED BY A LICENSED PROFESSIONAL, IT IS THE RESPONSIBILITY OF THE DEVELOPER/CLIENT TO RETAIN A LICENSED PROFESSIONAL TO SIGN AND SEAL THE PLANS. SJL SHALL NOT BE RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS TO THE PLANS AND SPECIFICATIONS UNLESS EXPRESSLY APPROVED BY SJL IN WRITING.THE CORNER116TH STREET & RANGELINECARMEL, INDIANA 46032PROJECT NUMBER: 118-1198 BUCKINGHAM COMPANIES 30 SOUTH MERIDIAN STREET, SUITE 1100 INDIANAPOLIS, INDIANA 46204 T: 317.974.1234 PROJECT ISSUE / DATE: IFC SET AUGUST 20, 2021 SCALE: ISSUE DATES: LRK 50 SOUTH B.B. KING BLVD. SUITE 600 MEMPHIS, TN 38103 T: 901.521.1440 ARCHITECT: STACY MILLER (PRINCIPAL) ANNA KARCHER (PROJECT MANAGER) KEY PLAN: 9 2 1 N . R I V E R F R O N T B L V D. S U I T E 1 0 0 D A L L A S , T E X A S 7 5 2 0 7 T: 2 1 4 . 4 4 3 . 9 0 9 0 F: 2 1 4 . 9 7 5 . 1 0 4 4 NOT FOR CONSTRUCTION - ©2021 SJL DESIGN GROUP PERMIT SET 06.16.2021 IFC SET 08.20.2021B B B 11/01/21