Loading...
HomeMy WebLinkAboutRepublic_HotelAdd-ADLS _ARCH AND LA DWGS 43Submitted by ESL-Spectrum Job Name: Republic Airways Corporate Campus - Ph 2 HQ ONLY Architect: Ratio Architects (Indianapolis) Engineer: Circle Design (Indianapolis) Catalog Number: ALT1/28L-85/3K7/4W/UNV/A34/**/BC RSAK20-40B-1-K2-** Notes: Type: S5 INDY24-116213 currentlighting.com/kimlighting © 2023 HLI Solutions, Inc. All rights reserved. Information and specifications subject to change without notice. All values are design or typical values when measured under laboratory conditions. Page 1 of 17 Rev 10/12/23 kl_Alt1_spec_R09 ALT1 ARCHITECTURAL AREA/SITE FEATURES • Elegant form factor • High performance optics up to 17,500 delivered lumens • Diffusion lens for low glare comfort • NX lighting controls options • IP66 Rated DATE:LOCATION: TYPE:PROJECT: CONSTRUCTION • One piece die-cast, low copper (<0.6% Cu) Aluminum Alloy 360 with vents and .100” minimum wall thickness. • Finish: fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) polyester powdercoat. • Optional lens is impact resistant 1/8” tempered glass with anti-reflective coating. • Optional lens has a one-piece extruded vulcanized silicone gasket. • Optional lens frame one piece die-cast, low copper (<0.6% Cu) Aluminum Alloy 360 and .100” minimum wall thickness. • Lens frame has a one-piece O-ring extruded vulcanized silicone gasket. • Mid-frame one piece die-cast, low copper (<0.6% Cu) Aluminum Alloy 360 and .100” minimum wall thickness. • Mid-frame secures to Lens Frame and housing by stainless steel recessed Allen-head screws. • Silicone gaskets throughout. • All external fasteners are stainless steel. ELECTRICAL (CONTINUED) • "Thermal Shield”, secondary side, thermistor provides protection for the sustainable life of LED module and electronic components. • Drivers have greater than a 0.9 power factor, less than 20% harmonic distortion, and be suitable for operation in -40°C to 40°C ambient environments. • Luminaire are capable of operating at 100% brightness in a 40°C environment. Both driver and optical array have integral thermal protection that will dim the luminaire upon detection of temperatures in excess of 85°C. • Modular wiring harness in the service area provides user access to the dimming circuitry. • Optional factory programmed dimming profile. • Surge protection: 20,000kA in series. • SF for 120, 277, 347 Line volts. DF for 208, 240, 480 Line volts. • Wiring: No. 18AWM rated 105°C, wet rating. SPECIFICATIONS CONTROL TECHNOLOGY OPTICS • LEDs mount to a metal printed circuit board assembly (MCPCB.) • Optical lenses are clear injection molded PMMA acrylic. • Optional Backlight Control on each LED module to completely control unwanted backlight. • Optional fixture finish optical surfaces will not exceed BUG ratings of the standard white finish and will be greater than or equal to the delivered lumens of the optional matte black optical surface finish. INSTALLATION • Fixtures must be grounded in accordance with national, state and/or local electrical codes. Failure to do so may result in serious personal injury. ELECTRICAL • Universal voltage, 120 through 277V with a ±10% tolerance. Driver is Underwriters Laboratories listed. • High voltage configurations, 347/480. Driver has a 0-10V dimming interface for multi-level illumination options. Driver is Underwriters Laboratories listed CATALOG #: (Specifications continued on page 4) IK08 3000K and warmer CCTs only IP66 Weight EPA- Front EPA- Side ALT1 21.5 lbs / 9.75 kg 0.37 ft2 0.64 ft2 3" (76 mm) 24.56" (624 mm) 7.5" (191 mm) Side View 14" (356 mm) 18.44" (468 mm) Top View Index Page1/21Submitted On: Mar 15, 2024