Loading...
HomeMy WebLinkAbout06060023 03 L801 Landscape DetailDO NOT HEAVILY PRUNE THE TREE AT PLANTING. PRUNE ONLY CROSSOVER LIMBS, CO— DOMINANT LEADERS, AND BROKEN OR DEAD BRANCHES. SOME INTERIOR TWIGS AND LATERAL BRANCHES MAY BE PRUNED; HOWEVER, DO NOT REMOVE THE TERMINAL BUDS OF BRANCHES THAT EXTEND TO THE EDGE OF THE CROWN. STAKE TREES ONLY UPON THE APPROVAL OF THE LANDSCAPE ARCHITECT SEE STAKING DETAIL WRAP TREE TRUNKS ONLY UPON THE APPROVAL OF THE LANDSCAPE ARCHITECT. SEE WRAPPING DETAIL MARK THE NORTH SIDE OF THE TREE IN THE NURSERY, AND ROTATE TREE TO FACE NORTH AT THE SITE WHEN EVER POSSIBLE. SET TOP OF ROOT BALL FLUSH TO GRADE OR 25 -50 MM (1 -2 IN.) HIGHER IN SLOWLY DRAINING SOILS. 200 MM (8 IN.) 75 MM (3 IN.) MULCH, DO NO PLACE MULCH INN CONTACT WITH TREE TRUNK. MAINTAIN THE MULCH WEED —FREE FOR A MINIMUM OF THREE YEARS AFTER PLANTING. NOTE: FOR DIMENSIONS OF PLANTING AREAS, TYPES OF SOIL AMENDMENTS, OR SOIL REPLACEMENT, SEE "SOIL IMPROVEMENT DETAILS." MULCH RING 1800 MM (6 FT.) DIAM. MIN. 400 MM (8 FT.) DIM. PREFERRED 1.111..1.11.1..1.1 1 I III... ..111.111111.1 i �T mo 4; EACH TREE MUST BE PLANTED SUCH THAT THE TRUNK FLARE IS VISIBLE AT THE TOP OF THE ROOT BALL. TREES WHERE THE TRUNK FLARE IS NOT VISIBLE SHALL BE REJECTED. DO NOT COVER THE TOP OF THE ROOT BALL WITH SOIL. 100 MM (4 IN.) HIGH EARTH SAUCER BEYOND EDGE OF ROOT BALL. REMOVE ALL TWINE, ROPE AND WIRE, AND BURLAP FROM TOP HALF OF ROOT BALL IF PLANT IS SHIPPED WITH A WIRE BASKET AROUND THE ROOT BALL, CUT THE WIRE BASKET IN FOUR PLACES AND FOLD DOWN 200 MM (8 IN.) INTO PLANTING HOLE. PLACE ROOT BALL ON UNEXCAVATED OR TAMPED SOIL. TAMP SOIL AROUND ROOT BALL BASE FIRMLY WITH FOOT PRESSURE SO THAT ROOT BALL DOES NOT SHIFT. TREE PLANTING DETAIL FOR B &B IN ALL SOIL TYPES SCALE: NOT TO SCALE NOTE: THIS DETAIL ASSUMES THAT THE PLANTING SPACE IS LARGER THAN AN 8' SQUARE OPEN TO THE SKY, AND NOT COVERED BY ANY PAVING OR GRATING. BIODEGRADABLE PLASTIC TAPE TWO— WALLED PLASTIC SHEETING OR TREE SHELTER MATERIAL APPLIED FROM TRUNK FLARE TO FIRST BRANCH APPLY THE PLASTIC SHEETING LOOSELY AROUND THE TRUNK TO LEAVE A 12 MM (0.5 IN.) GAP BETWEEN THE TRUNK AND THE SHEETING. OPTION 1 OPTION 2 BREATHABLE FABRIC TREE WRAP APPLIED FROM TRUNK FLARE TO FIRST BRANCH. WRAP PAPER FROM THE BOTTOM UP WITH SUFFICIENT OVERLAP TO COVER ALL BARK. PLASTIC TAPE. BIODEGRADABLE TREE WRAP SHOULD BE INSTALLED AT TIME OF PLANTING AND BE REMOVED WHEN DIRECTED BY THE LANDSCAPE ARCHITECT, BUT NO LATER THAN 12 MONTHS AFTER PLANTING. CONTRACTOR IS RESPONSIBLE FOR REMOVAL OF WRAPPING. TREE WRAPPING DETAIL SCALE: NOT TO SCALE REMOVE ANY TWINE OR SYNTHETIC TAPES FROM SHRUB TRUNK REMOVE BURLAP FROM TOP 1/3 OF ROOTBALL 3" SAUCER FILLED WITH 3 "SHREDDED BARK MULCH EXTENDED 6" FROM PIT BACKFILL PER SPECIFICATIONS ifEEMEIZA 12" MIN. FINISH GRADE EXISTING SUBSOIL OR COMPACTED BACKFILL SHRUB DETAIL SCALE: NOT TO SCALE WIRE OR CABLE SIZES SHALL BE AS FOLLOWS: TREES UP TO 65 MM (2.5 IN.) CALIPER 14 GAUGE TREES 65 MM (2.5 IN.) TO 75 MM (3 IN.) CALIPER 12 GAUGE TIGHTEN WIRE OR CABLE ONLY ENOUGH TO KEEP FROM SLIPPING. ALLOW FOR SOME TRUNK MOVEMENT. PLASTIC HOSE SHALL BE LONG ENOUGH TO ACCOMMODATE 35MM (1.5 IN.) OF GROWTH AND BUFFER ALL BRANCHES FROM THE WIRE. TUCK ANY LOOSE ENDS OF THE WIRE OR CABLE INTO THE WIRE WRAP SO THAT NO SHARP WIRE ENDS ARE EXPOSED. 13 MM (0.5 IN.) DIAM. PLASTIC HOSE GALVANIZED WIRE OR CABLE TWIST WIRE TO TIGHTEN. 3 240 x 40 MM (1.5 x 1.5 IN.) HARDWOOD STAKES OR OTHER APPROVED STAKE MATERIAL ALL STAKES SHALL BE DRIVEN OUTSIDE THE EDGE OF THE ROOT BALL. THE FIRST STAKE SHALL BE DIRECTLY SOUTHWEST OF THE TREE TRUNK. ASSURE THAT THE BEARING SURFACE OF THE PROTECTIVE COVERING OF THE WIRE OR IS A MINIMUM OF 12 MM (0.5 IN.). REMOVE ALL STAKING AS SOON AS THE TREE HAS GROWN SUFFICIENT ROOTS TO OVER THAT REQUIRED THE TREE TO BE STAKED. STAKES SHALL BE REMOVED NO LATER THE GROWING SEASON AFTER PLANTING. IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY C E uuunuluu 111111� 111.j11••1j11 1l uulun u .11..1....,.',I1/111.1�:, 11 111.., 111 ul ciratiis<:lmvw CABLE AGAINST THE TREE TRUNK COME THE PROBLEM END OF THE FIRST FULL TO REMOVE STAKING MATERIALS. TREE STAKING DETAIL, TREES 3" CALIPER OR LESS SCALE: NOT TO SCALE WIRE OR CABLE SIZES SHALL BE AS FOLLOWS: TREES UP TO 65 MM (2.5 IN.) CALIPER 14 GAUGE TREES 65 MM (2.5 IN.) TO 75 MM (3 IN.) CALIPER 12 GAUGE TIGHTEN WIRE OR CABLE ONLY ENOUGH TO KEEP FROM SLIPPING. ALLOW FOR SOME TRUNK MOVEMENT. PLASTIC HOSE SHALL BE LONG ENOUGH TO ACCOMMODATE 35MM (1.5 IN.) OF GROWTH AND BUFFER ALL BRANCHES FROM THE WIRE. TUCK ANY LOOSE ENDS OF THE WIRE OR CABLE INTO THE WIRE WRAP SO THAT NO SHARP WIRE ENDS ARE EXPOSED. INSTALL THREE GUY WIRES PER TREE, SPACED EVENLY AROUND THE TRUNK. 13 MM (0.5 IN.) DIAM. PLASTIC HOSE GALVANIZED WIRE OR CABLE TWIST WIRE TO TIGHTEN. TURNBUCKLES FOR TREES OVER 150 MM (6 IN.) CALIPER. 750 MM (30 IN.) LONG WOOD STAKE. ALL STAKES SHALL BE DRIVEN OUTSIDE THE EDGE OF THE ROOT BALL. PLASTIC FLAGGING OR OTHER VISUAL MARKER ON EACH WIRE. OPTIONAL METAL DRIVE ANCHORS, r INSTALLED PER MANUFACTURERS DIRECTIONS. ASSURE THAT THE BEARING SURFACE OF THE PROTECTIVE COVERING OF THE WIRE OR CABLE AGAINST THE TREE TRUNK IS A MINIMUM OF 12 MM (0.5 IN.) REMOVE ALL STAKING AS SOON AS THE TREE HAS GROWN SUFFICIENT ROOTS TO OVERCOME THE PROBLEM THAT REQUIRED THE TREE TO BE STAKED. STAKES SHALL BE REMOVED NO LATER THE END OF THE FIRST FULL GROWING SEASON AFTER PLANTING. IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO REMOVE STAKING MATERIALS. TREE STAKING DETAIL, TREES 3" CALIPER OR LARGER SCALE: NOT TO SCALE k WV I EXISTING SUBSOIL OR COMPACTED BACKFILL GROUNDCOVER DETAIL SCALE: NOT TO SCALE ROOTBALL GALVANIZED WIRE OR CABLE TWIST WIRE TO TIGHTEN. 4" HIGH EARTH SAUCER NOTE: LOCATE 1 STAKE DIRECTLY SOUTHWEST OF TREE TRUNK PLAN VIEW HARDWOOD STAKES OR OTHER APPROVED STAKE MATERIAL (TYP. OF 3) MULCH 13 MM (0.5 IN.) DIAM. PLASTIC HOSE TREE 3 L801 NOTE: FOR DETAILED REQUIREMENTS RELATED TO THE PLANTING OF THE TREE IN THE IMPROVED SOIL, SEE "TREE PLANTING DETAIL." LOAMY SOIL TAMP SOIL AROUND ROOT BALL BASE FIRMLY WITH FOOT PRESSURE SO THAT ROOT BALL DOES NOT SHIFT. 2 TIMES THE ROOT BALL DIAMETER BACK FILL WITH EXISTING SOIL. IN SANDY LOAM SOILS, ADD 20% MAX. BY VOLUME COMPOSTED ORGANIC MATERIAL TO THE EXISTING SOIL. 1:1 SLOPE ON SIDES OF PLANTING HOLE. UNEXCAVATED OR COMPACTED MOUND UNDER THE ROOT BALL TO PREVENT SETTLEMENT. LOAMY SOILS INCLUDE THE FOLLOWING USDA TEXTURAL CLASSIFICATIONS AND HAVE A CLAY CONTENT OF BETWEEN 15 TO 27 LOAM, SANDY LOAM AND SILT LOAM. NOTE THAT SOILS AT THE OUTER LIMITS OF THE LOAM CLASSIFICATIONS MAY PRESENT SPECIAL PLANTING PLANTING PROBLEMS NOT ANTICIPATED BY THIS DETAIL. LOAMY SOILS ARE DEFINED AS GRANULAR OR BLOCKY FRIABLE SOILS, A MIXTURE OF SAND, SILT AND CLAY PARTICLES WITH A MINIMUM OF 1.5% BY DRY WEIGHT ORGANIC MATTER. THE SOIL MUST NOT BE SO COMPACTED AS TO IMPEDE ROOT GROWTH OR DRAINAGE. THE SOIL STRUCTURE SHALL NOT BE PLATY OR MASSIVE. THE SOIL MUST BE TESTED FOR TEXTURE, DRAINAGE CAPABILITY, PH, AND NUTRIENT VALUES PRIOR TO DETERMINING ANY ADDITIONAL SOIL IMPROVEMENTS. CONTRACTOR SHALL CONSULT LANDSCAPE ARCHITECT IN POOR SOIL CONDITIONS. SOIL IMPROVEMENT DETAIL L801 1 SCALE: NOT TO SCALE SECTION 2 PLY HOSE TO SHEATH WIRE GALVANIZED TWISTED WIRE WOODEN STAKES PER SPECIFICATIONS (TYP. OF 3) 3" SHREDDED HARDWOOD BARK MULCH EXTENDED 6" BEYOND PIT (6' DIA. MIN.) DO NOT COVER TREE TRUNK 3" SOIL SAUCER FINISH GRADE REMOVE ANY TWINE OR SYNTHETIC TAPES REMO\/E BURLAP FROM TOP 1/3 OF ROOTBALL OR WIRE BASKET(IF APPLICABLE) EXCAVATE HOLE AND BACKFILL PER SPECIFICATIONS EXISTING SUBSOIL OR COMPACTED BACKFILL TREE STAKING DETAIL SCALE: NOT TO SCALE NOTE: TREES PLANTED IN NON RESTRICTED SOIL CONDITIONS. THIS DETAIL ASSUMES THAT THE AREA OF LOAMY SOIL AVAILABLE TO EACH TREE IS A MINIMUM OF 500 SQUARE FEET. EVERGREEN TREE DETAIL SCALE: NOT TO SCALE VERTICAL EDGE NOTE: STEEL LAWN EDGING SHALL BE USED AT ALL LAWN EDGES AND AT EDGES OF MULCHED AREAS (FOR CONTAINMENT). LAWN AREA PLANTING OR MULCHED AREA MULCH AS SPECIFIED EXISTING GRADE OR GRADE OF PLANTING AREA NOTE: TRENCH EDGE SHALL CREATE A CLEAN SEPERATION BETWEEN AREAS; AND SHALL CREATE SMOOTH AND EVEN LINES (AS INDICATED ON THE PLANS). 7 L801 VERTICAL EDGE DECORATIVE STONE SEE PLANS. STEEL EGDE RESTRAINT AS SPECIFIED MULCH AS SPECIFIED EXISTING GRADE OR GRADE OF PLANTING AREA NOTE: 1. STEEL LAWN EDGING SHALL CREATE A CLEAN SEPERATION BETWEEN PLANTING AREAS AND LAWN EDGES. 2. CREATE SMOOTHAND EVEN LINES AS INDICATED ON PLANS. 3. DO NOT USE STEEL LAWN EDGING FOR SPECIMEN OR SINGLE TREE. FOR TREES TO BE LOCATED IN LAWN ARES, CUT MULCH RING TRENCH TO SAME DIMENSIONS. 7 801 SPADE EDGE SCALE: NOT TO SCALE STEEL EDGE SCALE: NOT TO SCALE DATE: THIS DRAWING AND THE IDEAS, DESIGNS AND CONCEPTS CONTAINED HEREIN ARE THE EXCLUSIVE INTELLECTUAL PROPERTY OF THE SCHNEIDER CORPORATION, AND ARE NOT TO BE USED OR REPRODUCED, IN WHOLE OR IN PART, WITHOUT THE WRITTEN CONSENT OF THE SCHNEIDER CORPORATION. COPYRIGHTED BY THE SCHNEIDER CORP. (2005) ‘6, Schneider THE SCHNEIDER CORPORATION Historic Fort Harrison 8901 Otis Avenue Indianapolis, IN 46216 -1037 Telephone: 317.826.7100 Fax: 317.826.7200 www.schneidercorp.com Architecture Civil Engineering Environmental Engineering Geotechnical Services GIS LIS Home Builder Services Interior Design Land Surveying Landscape Architecture Transportation Engineering DATE: 6/16/09 PROJECT NO.: 3502.003 DRAWN BY: ZAB CHECKED BY: ALF SHEET TITLE: LANDSCAPE DETAILS DRAWING FILES: S: \3k \3502 \003 \dwgs \L101— L901.dwg XREF: S: \3k \3502 \003 \dwgs \Titlel.dwg XREF: S: \3k \3502 \003 \dwgs \003demobs.dwg XREF: S: \3k \3502 \003 \dwgs \003bs.dwg XREF: S: \3k \3502 \001 \dwgs \plat.dwg SHEET NO.: c 0 DO NOT HEAVILY PRUNE THE TREE AT PLANTING. PRUNE ONLY CROSSOVER LIMBS, CO— DOMINANT LEADERS, AND BROKEN OR DEAD BRANCHES. SOME INTERIOR TWIGS AND LATERAL BRANCHES MAY BE PRUNED; HOWEVER, DO NOT REMOVE THE TERMINAL BUDS OF BRANCHES THAT EXTEND TO THE EDGE OF THE CROWN. STAKE TREES ONLY UPON THE APPROVAL OF THE LANDSCAPE ARCHITECT SEE STAKING DETAIL WRAP TREE TRUNKS ONLY UPON THE APPROVAL OF THE LANDSCAPE ARCHITECT. SEE WRAPPING DETAIL MARK THE NORTH SIDE OF THE TREE IN THE NURSERY, AND ROTATE TREE TO FACE NORTH AT THE SITE WHEN EVER POSSIBLE. SET TOP OF ROOT BALL FLUSH TO GRADE OR 25 -50 MM (1 -2 IN.) HIGHER IN SLOWLY DRAINING SOILS. 200 MM (8 IN.) 75 MM (3 IN.) MULCH, DO NO PLACE MULCH INN CONTACT WITH TREE TRUNK. MAINTAIN THE MULCH WEED —FREE FOR A MINIMUM OF THREE YEARS AFTER PLANTING. NOTE: FOR DIMENSIONS OF PLANTING AREAS, TYPES OF SOIL AMENDMENTS, OR SOIL REPLACEMENT, SEE "SOIL IMPROVEMENT DETAILS." MULCH RING 1800 MM (6 FT.) DIAM. MIN. 400 MM (8 FT.) DIM. PREFERRED 1.111..1.11.1..1.1 1 I III... ..111.111111.1 i �T mo 4; EACH TREE MUST BE PLANTED SUCH THAT THE TRUNK FLARE IS VISIBLE AT THE TOP OF THE ROOT BALL. TREES WHERE THE TRUNK FLARE IS NOT VISIBLE SHALL BE REJECTED. DO NOT COVER THE TOP OF THE ROOT BALL WITH SOIL. 100 MM (4 IN.) HIGH EARTH SAUCER BEYOND EDGE OF ROOT BALL. REMOVE ALL TWINE, ROPE AND WIRE, AND BURLAP FROM TOP HALF OF ROOT BALL IF PLANT IS SHIPPED WITH A WIRE BASKET AROUND THE ROOT BALL, CUT THE WIRE BASKET IN FOUR PLACES AND FOLD DOWN 200 MM (8 IN.) INTO PLANTING HOLE. PLACE ROOT BALL ON UNEXCAVATED OR TAMPED SOIL. TAMP SOIL AROUND ROOT BALL BASE FIRMLY WITH FOOT PRESSURE SO THAT ROOT BALL DOES NOT SHIFT. TREE PLANTING DETAIL FOR B &B IN ALL SOIL TYPES SCALE: NOT TO SCALE NOTE: THIS DETAIL ASSUMES THAT THE PLANTING SPACE IS LARGER THAN AN 8' SQUARE OPEN TO THE SKY, AND NOT COVERED BY ANY PAVING OR GRATING. BIODEGRADABLE PLASTIC TAPE TWO— WALLED PLASTIC SHEETING OR TREE SHELTER MATERIAL APPLIED FROM TRUNK FLARE TO FIRST BRANCH APPLY THE PLASTIC SHEETING LOOSELY AROUND THE TRUNK TO LEAVE A 12 MM (0.5 IN.) GAP BETWEEN THE TRUNK AND THE SHEETING. OPTION 1 OPTION 2 BREATHABLE FABRIC TREE WRAP APPLIED FROM TRUNK FLARE TO FIRST BRANCH. WRAP PAPER FROM THE BOTTOM UP WITH SUFFICIENT OVERLAP TO COVER ALL BARK. PLASTIC TAPE. BIODEGRADABLE TREE WRAP SHOULD BE INSTALLED AT TIME OF PLANTING AND BE REMOVED WHEN DIRECTED BY THE LANDSCAPE ARCHITECT, BUT NO LATER THAN 12 MONTHS AFTER PLANTING. CONTRACTOR IS RESPONSIBLE FOR REMOVAL OF WRAPPING. TREE WRAPPING DETAIL SCALE: NOT TO SCALE REMOVE ANY TWINE OR SYNTHETIC TAPES FROM SHRUB TRUNK REMOVE BURLAP FROM TOP 1/3 OF ROOTBALL 3" SAUCER FILLED WITH 3 "SHREDDED BARK MULCH EXTENDED 6" FROM PIT BACKFILL PER SPECIFICATIONS ifEEMEIZA 12" MIN. FINISH GRADE EXISTING SUBSOIL OR COMPACTED BACKFILL SHRUB DETAIL SCALE: NOT TO SCALE WIRE OR CABLE SIZES SHALL BE AS FOLLOWS: TREES UP TO 65 MM (2.5 IN.) CALIPER 14 GAUGE TREES 65 MM (2.5 IN.) TO 75 MM (3 IN.) CALIPER 12 GAUGE TIGHTEN WIRE OR CABLE ONLY ENOUGH TO KEEP FROM SLIPPING. ALLOW FOR SOME TRUNK MOVEMENT. PLASTIC HOSE SHALL BE LONG ENOUGH TO ACCOMMODATE 35MM (1.5 IN.) OF GROWTH AND BUFFER ALL BRANCHES FROM THE WIRE. TUCK ANY LOOSE ENDS OF THE WIRE OR CABLE INTO THE WIRE WRAP SO THAT NO SHARP WIRE ENDS ARE EXPOSED. 13 MM (0.5 IN.) DIAM. PLASTIC HOSE GALVANIZED WIRE OR CABLE TWIST WIRE TO TIGHTEN. 3 240 x 40 MM (1.5 x 1.5 IN.) HARDWOOD STAKES OR OTHER APPROVED STAKE MATERIAL ALL STAKES SHALL BE DRIVEN OUTSIDE THE EDGE OF THE ROOT BALL. THE FIRST STAKE SHALL BE DIRECTLY SOUTHWEST OF THE TREE TRUNK. ASSURE THAT THE BEARING SURFACE OF THE PROTECTIVE COVERING OF THE WIRE OR IS A MINIMUM OF 12 MM (0.5 IN.). REMOVE ALL STAKING AS SOON AS THE TREE HAS GROWN SUFFICIENT ROOTS TO OVER THAT REQUIRED THE TREE TO BE STAKED. STAKES SHALL BE REMOVED NO LATER THE GROWING SEASON AFTER PLANTING. IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY C E uuunuluu 111111� 111.j11••1j11 1l uulun u .11..1....,.',I1/111.1�:, 11 111.., 111 ul ciratiis<:lmvw CABLE AGAINST THE TREE TRUNK COME THE PROBLEM END OF THE FIRST FULL TO REMOVE STAKING MATERIALS. TREE STAKING DETAIL, TREES 3" CALIPER OR LESS SCALE: NOT TO SCALE WIRE OR CABLE SIZES SHALL BE AS FOLLOWS: TREES UP TO 65 MM (2.5 IN.) CALIPER 14 GAUGE TREES 65 MM (2.5 IN.) TO 75 MM (3 IN.) CALIPER 12 GAUGE TIGHTEN WIRE OR CABLE ONLY ENOUGH TO KEEP FROM SLIPPING. ALLOW FOR SOME TRUNK MOVEMENT. PLASTIC HOSE SHALL BE LONG ENOUGH TO ACCOMMODATE 35MM (1.5 IN.) OF GROWTH AND BUFFER ALL BRANCHES FROM THE WIRE. TUCK ANY LOOSE ENDS OF THE WIRE OR CABLE INTO THE WIRE WRAP SO THAT NO SHARP WIRE ENDS ARE EXPOSED. INSTALL THREE GUY WIRES PER TREE, SPACED EVENLY AROUND THE TRUNK. 13 MM (0.5 IN.) DIAM. PLASTIC HOSE GALVANIZED WIRE OR CABLE TWIST WIRE TO TIGHTEN. TURNBUCKLES FOR TREES OVER 150 MM (6 IN.) CALIPER. 750 MM (30 IN.) LONG WOOD STAKE. ALL STAKES SHALL BE DRIVEN OUTSIDE THE EDGE OF THE ROOT BALL. PLASTIC FLAGGING OR OTHER VISUAL MARKER ON EACH WIRE. OPTIONAL METAL DRIVE ANCHORS, r INSTALLED PER MANUFACTURERS DIRECTIONS. ASSURE THAT THE BEARING SURFACE OF THE PROTECTIVE COVERING OF THE WIRE OR CABLE AGAINST THE TREE TRUNK IS A MINIMUM OF 12 MM (0.5 IN.) REMOVE ALL STAKING AS SOON AS THE TREE HAS GROWN SUFFICIENT ROOTS TO OVERCOME THE PROBLEM THAT REQUIRED THE TREE TO BE STAKED. STAKES SHALL BE REMOVED NO LATER THE END OF THE FIRST FULL GROWING SEASON AFTER PLANTING. IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO REMOVE STAKING MATERIALS. TREE STAKING DETAIL, TREES 3" CALIPER OR LARGER SCALE: NOT TO SCALE k WV I EXISTING SUBSOIL OR COMPACTED BACKFILL GROUNDCOVER DETAIL SCALE: NOT TO SCALE ROOTBALL GALVANIZED WIRE OR CABLE TWIST WIRE TO TIGHTEN. 4" HIGH EARTH SAUCER NOTE: LOCATE 1 STAKE DIRECTLY SOUTHWEST OF TREE TRUNK PLAN VIEW HARDWOOD STAKES OR OTHER APPROVED STAKE MATERIAL (TYP. OF 3) MULCH 13 MM (0.5 IN.) DIAM. PLASTIC HOSE TREE 3 L801 NOTE: FOR DETAILED REQUIREMENTS RELATED TO THE PLANTING OF THE TREE IN THE IMPROVED SOIL, SEE "TREE PLANTING DETAIL." LOAMY SOIL TAMP SOIL AROUND ROOT BALL BASE FIRMLY WITH FOOT PRESSURE SO THAT ROOT BALL DOES NOT SHIFT. 2 TIMES THE ROOT BALL DIAMETER BACK FILL WITH EXISTING SOIL. IN SANDY LOAM SOILS, ADD 20% MAX. BY VOLUME COMPOSTED ORGANIC MATERIAL TO THE EXISTING SOIL. 1:1 SLOPE ON SIDES OF PLANTING HOLE. UNEXCAVATED OR COMPACTED MOUND UNDER THE ROOT BALL TO PREVENT SETTLEMENT. LOAMY SOILS INCLUDE THE FOLLOWING USDA TEXTURAL CLASSIFICATIONS AND HAVE A CLAY CONTENT OF BETWEEN 15 TO 27 LOAM, SANDY LOAM AND SILT LOAM. NOTE THAT SOILS AT THE OUTER LIMITS OF THE LOAM CLASSIFICATIONS MAY PRESENT SPECIAL PLANTING PLANTING PROBLEMS NOT ANTICIPATED BY THIS DETAIL. LOAMY SOILS ARE DEFINED AS GRANULAR OR BLOCKY FRIABLE SOILS, A MIXTURE OF SAND, SILT AND CLAY PARTICLES WITH A MINIMUM OF 1.5% BY DRY WEIGHT ORGANIC MATTER. THE SOIL MUST NOT BE SO COMPACTED AS TO IMPEDE ROOT GROWTH OR DRAINAGE. THE SOIL STRUCTURE SHALL NOT BE PLATY OR MASSIVE. THE SOIL MUST BE TESTED FOR TEXTURE, DRAINAGE CAPABILITY, PH, AND NUTRIENT VALUES PRIOR TO DETERMINING ANY ADDITIONAL SOIL IMPROVEMENTS. CONTRACTOR SHALL CONSULT LANDSCAPE ARCHITECT IN POOR SOIL CONDITIONS. SOIL IMPROVEMENT DETAIL L801 1 SCALE: NOT TO SCALE SECTION 2 PLY HOSE TO SHEATH WIRE GALVANIZED TWISTED WIRE WOODEN STAKES PER SPECIFICATIONS (TYP. OF 3) 3" SHREDDED HARDWOOD BARK MULCH EXTENDED 6" BEYOND PIT (6' DIA. MIN.) DO NOT COVER TREE TRUNK 3" SOIL SAUCER FINISH GRADE REMOVE ANY TWINE OR SYNTHETIC TAPES REMO\/E BURLAP FROM TOP 1/3 OF ROOTBALL OR WIRE BASKET(IF APPLICABLE) EXCAVATE HOLE AND BACKFILL PER SPECIFICATIONS EXISTING SUBSOIL OR COMPACTED BACKFILL TREE STAKING DETAIL SCALE: NOT TO SCALE NOTE: TREES PLANTED IN NON RESTRICTED SOIL CONDITIONS. THIS DETAIL ASSUMES THAT THE AREA OF LOAMY SOIL AVAILABLE TO EACH TREE IS A MINIMUM OF 500 SQUARE FEET. EVERGREEN TREE DETAIL SCALE: NOT TO SCALE VERTICAL EDGE NOTE: STEEL LAWN EDGING SHALL BE USED AT ALL LAWN EDGES AND AT EDGES OF MULCHED AREAS (FOR CONTAINMENT). LAWN AREA PLANTING OR MULCHED AREA MULCH AS SPECIFIED EXISTING GRADE OR GRADE OF PLANTING AREA NOTE: TRENCH EDGE SHALL CREATE A CLEAN SEPERATION BETWEEN AREAS; AND SHALL CREATE SMOOTH AND EVEN LINES (AS INDICATED ON THE PLANS). 7 L801 VERTICAL EDGE DECORATIVE STONE SEE PLANS. STEEL EGDE RESTRAINT AS SPECIFIED MULCH AS SPECIFIED EXISTING GRADE OR GRADE OF PLANTING AREA NOTE: 1. STEEL LAWN EDGING SHALL CREATE A CLEAN SEPERATION BETWEEN PLANTING AREAS AND LAWN EDGES. 2. CREATE SMOOTHAND EVEN LINES AS INDICATED ON PLANS. 3. DO NOT USE STEEL LAWN EDGING FOR SPECIMEN OR SINGLE TREE. FOR TREES TO BE LOCATED IN LAWN ARES, CUT MULCH RING TRENCH TO SAME DIMENSIONS. 7 801 SPADE EDGE SCALE: NOT TO SCALE STEEL EDGE SCALE: NOT TO SCALE DATE: THIS DRAWING AND THE IDEAS, DESIGNS AND CONCEPTS CONTAINED HEREIN ARE THE EXCLUSIVE INTELLECTUAL PROPERTY OF THE SCHNEIDER CORPORATION, AND ARE NOT TO BE USED OR REPRODUCED, IN WHOLE OR IN PART, WITHOUT THE WRITTEN CONSENT OF THE SCHNEIDER CORPORATION. COPYRIGHTED BY THE SCHNEIDER CORP. (2005) ‘6, Schneider THE SCHNEIDER CORPORATION Historic Fort Harrison 8901 Otis Avenue Indianapolis, IN 46216 -1037 Telephone: 317.826.7100 Fax: 317.826.7200 www.schneidercorp.com Architecture Civil Engineering Environmental Engineering Geotechnical Services GIS LIS Home Builder Services Interior Design Land Surveying Landscape Architecture Transportation Engineering