The URL can be used to link to this page

Home My WebLink About155913 01/23/2008 CITY OF CARMEL, INDIANA VENDOR: 00351248 Page 1 of 1 ONE CIVIC SQUARE JEFF STEWART CARMEL, INDIANA 46032 C/O STREET DEPT CHECK AMOUNT: $22.49 C/O STREET DEPT CHECK NUMBER: 155913 CHECK DATE: 1123/2008 DEP ARTMENT ACCOUNT PO NUMBER INVOICE NUMBER AMOUNT DESCRIPTION -R 2201 .4237000 22.49 REPAIR PARTS 3875 CALIFORNIA ROAD ORCHARD PARK, NY 14127 INVOICE NO NCR �Wphone: 1-800444-5847 619354 BILL TO JEFF STEWART CARMEL STREET DEPARTMENT 3400 WEST 131ST STREET WESTFIELD IN 46074 PAYMENT FILLED ENTERED SHIP DATE TYPE SHIPPED VIA BY BY PURCHASE ORDER NO 1/14/08 FIRST CLASS DAL ID NUMBER CREDIT CARD NUMBER 81335379288X CITY PART NUMBER DESCRIPTION PRICE EXTENSION 1 040379 288 SPARE TIRE KEY,5 2 &3 22.49 22.49 PER PHONE .00 31 .733 .2 .00 PRE -PAID BALANCE Please check parts caretlly. SUB TOTAL SHIPPING TOTAL AMOUNT DUE It wrong please return with 22.49 .00 1 22.49 22.49 .00 Invoice within 30 days BALANCE DUE UPON RECEIPT INSTALLATION OF MCGARD LOCK NUTS/LOCK BOLTS: 1 Remove wheel covers (if equipped) and one luo nut %bolt from each v. Verify that lock style, searing surface style (cone, radius, flat, shank, etc and thread sizA match the lug nuubolt removed. `f sturA are rusty. clean with a wire brush prior to installing wheel locks. Note: When servicing jour vehicle, the lock should alivaa s be the first fastener removed from the wheel and the last fastener Installed o,ato toe ✓heel. 2 By hand. install a McGard Wheel Lock onto each wheel. Use cne lick per vrheel. Notice: Impact gums usually cannot be set and /or maintain proper pressure to obtain proper installation torque and should not be used for lock installation. Use of impact guns (pneumatic, electric, etc.) for installation may cause overtightening and permanent damage to lock and key. Never use an impact gun with a key that has a cable or that is attached to another object via a cable or other means. 3 Using the McGard key and a wrench, tighten each lock to the torque specified in your vehicle owner's manual. For best results, use a torque wrench and socket. Keep the key pattern firmly and squarely engaged into the lock pattern. They can be kept square to each other via direct inward pressure. This will prevent uneven pressure on the key which could result in damage to the lock and /or key. Notes: A) Overtightening the lock could result in difficulty of removal. B) McGard does not recommend the use of oil, grease or anti -seize lubricants on threads. C) If installing closed -end lug nuts or lock nuts, make sure that they have not bottomed out on the stud (bottomed out refers to the closed end of the nut resting on the stud, while the bottom of the nut fails to fully contact the wheel). Check for space or gaps between wheel and lock nut. D) If installing lock bolts, make sure the shank length matches your lug bolt. Too short a length could cause thread damage. Too long a length can extend beyond the rotor and cause damage to other vehicle parts. 4 Re- torque the locks after 25 miles of driving. REMOVAL OF OVERTIGHTENED LOCK NUTS /LOCK (DOLTS: Warning: Eye protection must be used when removing overtightened locks. WARNING: Use of an impact gun on a key with a cable or key cabled to a lug wrench can cause serious injury. 1 Overtighten all lug nuts /bolts on the problem wheel to remove pressure from the lock nut /bolt. Do not tighten to the point of stud or lug nut/bolt thread damage. 2 Remove the lock with your key. When using hand tools such as a lug wrench, ratchet, etc. direct inward pressure on the key must be used. This will keep the key pattern firmly and squarely engaged into the lock pattern. Normally McGard does not recommend the use of an impact gun, but if the key is not attached to another object (some McGard keys are equipped with a plastic or steel cable) an impact gun does work best for removing overtightened locks. If using an impact gun, the lock may not come free immediately. Continue using the impact gun as the repeated ratchet motion will slowly loosen the lock. If the lock is not free after a few minutes, try to remove the lock using a ratchet or breaker bar. (making sure to keep direct inward pressure). 3 If the lock does not free itself, loosen one lug nut /bolt (4 hole wheels) or two lug nuts /bolts (5 hole wheels) opposite the lock and repeat step 2. Note: If the lock still will not come off. call McGard Customer Service Department at the number below for further instructions. 4 Upon removal of the lock, remove all lug nuts /bolts and remount the wheel. Install the lock per the installation instruc- tions found on this page. If you have any questions, call McGard Customer Service 8am -5pm Eastern Time, 1- 800 444 -5847. 08833A Prescribed by State Board of Accounts ACCOUNTS PAYABLE VOUCHER City Form No. 201 (Rev. 1995) CITY OF CARMEL An invoice or bill to be properly itemized must show: kind of service, where performed, dates service rendered, by ;whom, rates per day, number of hours, rate per hour, number of units, price per unit, etc. Payee Purchase Order No. Terms Date Due Invoice Invoice Description Amount Date Number (or note attached invoice(s) or bill(s)) 6 Total I hereby certify that the attached invoice(s), or bill(s), is (are) true and correct and I have audited same in accordance with IC 5- 11- 10 -1.6. 20 Clerk- Treasurer VOUCHER NO. WARRANT NO. r ALLOWED 20 IN SUM OF ON ACCOUNT OF APPROPRIATION FOR Board Members PO# or INVOICE NO. ACCT #/TITLE AMOUNT DEPT. I hereby certify that the attached invoice(s), or (D 1 G 3 `J q 6 0 bill(s) is (are) true and correct and that the materials or services itemized thereon for which charge is made were ordered and received except Q 20 Sign t re Cost distribution ledger classification if Title claim paid motor vehicle highway fund