Loading...
HomeMy WebLinkAboutLighting Cut sheets 062113www.speclight.com SERIES RLM PRoduct infoRMation: 994 Jefferson Street, Fall River, MA 02721 508.678.2303 FAX 508.678.2260 cat. PRoJEct:tYPE: Dimensions shown are nominal. Spectrum Lighting is continually improving products and reserves the right to make changes that will not alter performance or appearance with or without written notice. • Pier Light Short features limited side light. • Fixture is constructed of spun and die cast aluminum. • Compact fluorescent, metal halide and incandescent lamping available. • Variety of powdercoat finishes. Interior finished gloss white with color exterior. • Standard fixture damp location listed. • WL-Wet location available. • Manufactured and built to UL standard No 1598. PS1408cf PS1609cf PS2011cf PS1408MH PS1609MH PS2011MH PS1408inc PS1609inc PS2011inc PS1408cf MoDeL 13/18/26/32/42 13/18/26/32/42 13/18/26/32/42 50/70/100 50/70/100 50/70/100 100w 150w 200w 26 Ex GJ2 WL WATTS LAMP eNCLoSUReBALLAST ModEL # PS1408 PS1609 PS2011 a 14” 16” 20” B 8” 9” 11” GW- Gloss White finish Shown GW *** See SPeCTRUM Color Chart for a Full List GW GB EG VE aY BL oR Rd BZ co Si MM cc -Gloss White -Gloss Black -evergreen -Verde Green -Aero Yellow -Blue Streak -orange -Red Baron -Bronze -Copper Metalic -Silver -Metal Finish (Brushed Copper, Brushed Aluminum, Polished Brass) Consult Factory -Custom Color Ex EMRM Ex RMB REB - electronic, 120/277v (18/26/32/42) -CF Remote emergency Battery Pack - electronic, 120/277v (50/70/100) -MH Remote F-Can, Magnetic Ballast -MH Remote electronic Ballast FINISH***MoUNTING cP-106 Ballast Housing SPeCIFY MoUNTING PIPe PRoFILe** Pa23 Shown B a GJ2 fJ2 LJ2 WL SS1 BS1 - Glass Lamp enclosure -Frosted Lamp enclosure -Prismatic Polycarbonate Lamp enclosure -Wet Location (No Cable Mounting) -Side Glare Shield -Bottom Glare Shield Max 42w cf/100w MH/200w inc PiER LiGHt SHoRt CF / INC / MH WaLL Mount * Specify Length in Inches Pa15 cP6 cP3 cP106 cd* cdcc* cM* HM* PM* cP13 - See RLM Mounting Page for Available Arm Options -Wall Pipe Interface (INC) -CP6 Decorative Cover (INC) -Wall Ballast Housing (CF/MH) -Cord and Cable Mount (No WL ) -Coil Cord and Cable Mount (No WL ) -Cord Mount -Hang Straight Pendant -Pendant/Straight Mount -Ballast Housing Pa15 / cP106 cEiLinG Mount 501 BAR OPTIONS GRILL Decorative Aluminum Grill MPERF Middle Perf WEB Double Cross Bars with Two Full Vertical Bars DC/2MB Double Cross Bars with Two Middle Bars DC/2VB Double Cross Bars with Two Vertical Bars 3CB Three Cross Bars Standard Unit VB Vertical Bar DC Double Cross Bars 501 BAR OPTIONS TYPE PROJECT: LOCATION: FEATURES DIMENSIONS ORDERING INFORMATION / OPTIONS EXAMPLE: 501-2CFQ13-SAL-VB 501 MODEL 501 - Classic LAMP 2CFQ13 - (2) 13W QUAD TUBE CF (G24Q-1 BASE) 2CFQ18 - (2) 18W QUAD TUBE CF (G24Q-2 BASE) 2CFQ26 - (2) 26W QUAD TUBE CF (G24Q-3 BASE) Consult factory for other available lamps. HOUSING FINISH WHT - White BLK - Black SAL - Silver BRZ - Bronze BA - Brushed Aluminum Consult factory for other finishes. OPTIONS BL - Bottom Lens TC - Top Die Cast Aluminum Cover (Adds ½” to height) BC - Bottom Die Cast Aluminum Cover (Adds ½” to height) Faux - Faux Alabaster Lens DIM - Dimming Ballast Lamp - Lamp provided, please specify color temperature For emergency ballast availability, consult model 507. • A timeless design for a classic look. • Cage constructed of solid aluminum bar stock for strength and rigidity. • Available with a wide variety of bar configurations. • Electronic, multi-volt (120/277) ballast is standard. • All parts are treated with a five stage phosphate bonding process before being finished with a long lasting powder coat finish. • Acrylic lens for maximum lens uniformity. • Complies with ADA. • No visible fasteners. • Manufactured in the U.S.A. • Available in longer lengths consult factory. Contact your local sales rep for other available sizes/bar configurations. BAR CONFIGURATION Blank - Standard Single Bar VB - Vertical Bar DC - Double Cross Bar DC/2VB - Double Cross Bar w/2 Vertical Bars DC/2MB - Double Cross Bar w/2 Middle Bars 3CB - 3 Lower Cross Bars WEB - Double Cross Bar w/2 Full Vertical Bars MPERF - Vertical Perf Panel in the Center of the Fixture GRILL - Decorative Aluminum Grill Consult factory for other available configurations. MC = Mounting Center A 4” octagonal junction box should be used for installation. Indessa Lighting reserves the right to make design revisions without prior notice. PHONE: 509.924.0243 • FAX: 509.924.2607 • www.indessa.com WET LOCATION 4 7-1/4 MC 6-5/8 14-1/2 VB DCSingle Bar (Standard)WEB DC/2MB 3CB MPERF Top Cover Bottom Cover GRILLDC/2VB OUTDOOR KAD-M-S Catalog Number Notes Type All dimensions are inches (centimeters) unless otherwise specified. *Weight as configured in example below. KAD Series Wattage Distribution Voltage Ballast Mounting12 KAD Metal halide 70M1,2 250M5 100M1 320M4 150M 350M3,4 175M 3 400M5,6 200M4 High pressure sodium1 70S 100S 150S 250S 400S Ceramic metal halide 70MHC1,2 100MHC1 150MHC Standard reflectors R2 IES type II asymmetric7 R3 IES type III asymmetric7 R4 IES type IV forward throw7 R5S IES type V square High performance reflectors8 SR2 IES type II asymmetric7 SR3 IES type III asymmetric7 SR4SC IES type IV forward throw 120 2089 240 9 277 347 4809 TB10 23050HZ11 (blank)Magnetic ballast CWI Contant wattage isolated11 SCWA Super CWA pulse-start ballast NOTE: For shipments to U.S. territories, SCWA must be specified to comply with EISA. Ships in fixture carton SPD__Square pole RPD__Round pole WBD__Wall bracket WWD__Wood or pole wall Ships separately13,14 DAD12PDegree arm (pole) DAD12WB Degree arm (wall) WBA Decorative wall bracket15 KMA Mast arm external fitter KTMB Twin mounting bar Arm length 04 4" arm 06 6" arm 09 9" arm 12 12" arm ORDERING INFORMATION For shortest lead times, configure product using bolded options.Example: KAD 400M R3 TB SCWA SPD04 LPI Options Finish20 Lamp21 Shipped installed in fixture SFSingle fuse (120, 277, 347V)16 DFDouble fuse (208, 240, 480V)16 PD Power tray17 PER NEMA twist-lock receptacle only (no photocontrol) QRSQuartz restrike system18 QRSTDQRS time delay18 WTB Terminal wiring block17 CSA CSA Certified INTL Available MH for probe start shipping outside the U.S. REGC1California Title 20, effective 1/1/2010 Shipped separately13 HS House side shield PE1NEMA twist-lock PE (120, 208, 240V) PE3 NEMA twist-lock PE (347V) PE4 NEMA twist-lock PE (480V) PE7 NEMA twist-lock PE (277V) SCShorting cap for PER option VG Vandal guard19 WG Wire guard19 (blank)Dark bronze DWH White DBL Black DMB Medium bronze DNA Natural aluminum Super Durable Finishes DDBXDDark bronze DBLXDBlack DNAXDNatural aluminum DWHXDWhite DDBTXDTextured dark bronze DBLBXDTextured black DNATXDTextured natural aluminum DWHGXDTextured white LPI Lamp included L/LP Less lamp Soft Square Lighting KAD METAL HALIDE: 70-400W HIGH PRESSURE SODIUM: 70-400W 20’ TO 35’ MOUNTING Specifications EPA: 1.2 ft.2 *Weight: 35.9 lbs (16.28 kg) Length: 17-1/2 (44.5) Width: 17-1/2” (44.5) Depth: 7-1/8 (18.1) FEATURES & SPECIFICATIONS INTENDED USE – Ideal for parking areas, street lighting, walkways and car lots. CONSTRUCTION – Rugged, die-cast, soft corner aluminum housing with 0.12” nominal wall thickness. Die-cast door frame has impact-resistant,tempered, glass lens that is fully gasketed with one-piece tubular silicone. Finish: Standard finish is dark bronze (DDB) polyester powder finish, with other architectural colors available. OPTICS – Anodized, aluminum reflectors: IES full cutoff distributions R2 (asymmetric), R3 (asymmetric), R4 (forward throw) and R5S (square) are interchangeable. High-performance anodized, segmented aluminum reflectors IES full cutoff distributions SR2 (asymmetric), SR3 (asymmetric) and SR4SC (forward throw, sharp cutoff). High-performance reflectors attach with tool-less fasteners and are rotatable and interchangeable. ELECTRICAL – Ballast: High pressure sodium: 70-150W is high reactance, high power factor. Constant wattage autotransformer for 200-400W. Metal halide: 70-150W is high reactance, high power factor and is standard with pulse-start ignitor technology. “SCWA” not required. Constant wattage autotransformer for 175-400W. Super CWA (pulse start ballast), 88% efficient and EISA legislation compliant, is required for metal halide 151-400W (SCWA option) for US shipments only. CSA, NOM or INTL required for probe start shipments outside of the US. Pulse-start ballast (SCWA) required for 200W, 320W, or 350W. Ballast is 100% factory-tested. Socket: Porcelain, horizontally oriented medium base socket for 70-150M. Mogul base socket for 175M and above, and 70-400S, with copper alloy, nickel-plated screw shell and center contact. UL listed 1500W, 600V. LISTINGS – UL Listed (standard). CSA Certified (see Options). UL listed for 25°C ambient and wet locations. IP65 rated in accordance with standard IEC 529. WARRANTY — 1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx Note: Specifications subject to change without notice. Notes 1 Not available with SCWA. 2 Not available with 480V. 3 These wattages do not comply with California Title 20 regulations. 4 Must be ordered with SCWA. 5 These wattages require the REGC1 option to be chosen for shipments into California for Title 20 compliance. 250M REGC1 in not available in 347 or 480V. 6 Reduced jacket ED28 required for SR2, SR3 and SR4SC optics. 7 House-side shield available. 8 High performance reflectors not avail- able with QRSTD. 9 Must specify CWI for use in Canada. 10 Optional multi-tap ballast (120, 208, 240, 277V; in Canada: 120, 277, 347V). 11 Consult factory for available wattages. 12 9" arm is required when two or more luminaires are oriented on a 90° drilling pattern. 13 May be ordered as an accessory. 14 Must specify finish when ordered as an accessory. 7-1/8(18.1) 4(10.2)17-1/2(44.5) ® Accessories: Tenon Mounting Slipfitter (RPxx required.) Order as seperate catalog number. Must be used with pole mounting. Number of fixtures Tenon O.D.One Two@180°Two@90°Three@120°Three@90°Four@90° 2-3/8"T20-190 T20-280 T20-29022 T20-32022 T20-39022 T20-49022 2-7/8"T25-190 T25-280 T25-29022 T25-320 T25-39022 T25-49022 4 T35-190 T35-280 T35-29022 T35-320 T35-39022 T35-49022 15 Available with SPD04 and SPD09. 16 Must specicy voltage. N/A with TB. 17 Only available with SR2, SR3 and SR4SC optics. 18 Max allowable wattage lamp included. 19 Prefix with KAD when ordered as an accessory. 20 See www.lithonia.com/archcolors for additional color options. 21 Must be specified. L/LP not available with MHC. 22 Must use RPD09. KAD-M-S OUTDOOR: One Lithonia Way Conyers, GA 30012 Phone: 770.922.9000 Fax: 770-918-1209 www.lithonia.com ©2007-2012 Acuity Brands Lighting, Inc. All rights reserved. Rev.12/04/12 KAD Metal Halide, Arm-mounted Soft Square Cutoff Mounting Height Correction Factor (Multiply the fc level by the correction factor) 25 ft. = 0.64 35 ft. = 0.32 40 ft. = 0.25 Coefficient of Utilization Initial Footcandles Notes 1 Photometric data for other distributions can be accessed at www.lithonia.com. 2 Tested to current IES and NEMA standards under stabilized laboratory conditions. Various operating factors can cause differences between laboratory data and actual field measurements. Dimensions and specifications on this sheet are based on the most current available data and are subject to change without notice. 3 For electrical characteristics, consult outdoor technical data specification sheets on www.lithonia.com. Existing Mounting Height New Mounting Height 2 = Correction Factor KAD 400M R2 Test no. 1193083101P KAD 400M R3 Test no. 1192040902P KAD 400M R4HS Test no. 1192061101P KAD 400M R4 Test no. 1191110101P DI S T A N C E I N U N I T S O F M O U N T I N G H E I G H T ISOILLUMINANCE PLOT (Footcandle) 400W pulse start metal halide lamp, rated 38000 lumens. Footcandle values based on 20' mounting height. Classification: Type II, Short, Full Cutoff -3 -2 -1 0 1 2 3 4 012345 6 5 2.5 1.510.50.25 DI S T A N C E I N U N I T S O F M O U N T I N G H E I G H T ISOILLUMINANCE PLOT (Footcandle) 400W pulse start metal halide lamp, rated 38,000 lumens. Footcandle values based on 20' mounting height. Classification: Type II, Short, Full Cutoff -3 -2 -1 0 1 2 3 4 012345 6 5 2.5 1.510.5 0.25 DI S T A N C E I N U N I T S O F M O U N T I N G H E I G H T ISOILLUMINANCE PLOT (Footcandle) 400W pulse start metal halide lamp, rated 38,000 lumens. Footcandle values based on 20' mounting height. Classification: Unclassified (Type III, Very Short), Full Cutoff -3 -2 -1 0 1 2 3 4 012345 6 52.51.510.5 0.25 DI S T A N C E I N U N I T S O F M O U N T I N G H E I G H T ISOILLUMINANCE PLOT (Footcandle) 400W pulse start metal halide lamp, rated 38,000 lumens. Footcandle values based on 20' mounting height. Classification: Unclassified (Type III, Very Short), Full Cutoff -3 -2 -1 0 1 2 3 4 012345 6 52.51.510.50.25 KAD 400M R5S Test no. 1194040801P DI S T A N C E I N U N I T S O F M O U N T I N G H E I G H T ISOILLUMINANCE PLOT (Footcandle) 400W pulse start metal halide lamp, rated 38000 lumens. Footcandle values based on 20' mounting height. Classification: Unclassified (Type NC, Very Short), Full Cutoff -3 -2 -1 0 1 2 3 4 012345 6 5 2.51.510.5 0.25 Catalog Number Notes Type OUTDOOR POLE-SSS FEATURES & SPECIFICATIONS INTENDED USE — Square straight steel pole for up to 39-foot mounting height. CONSTRUCTION — Weldable-grade, hot-rolled, commercial-quality carbon steel tubing with a minimum yield of 55,000 psi (11-gauge), or 50,000 psi (7-gauge). Uniform wall thickness of .1196" or .1793". Shaft is one-piece with a full-length longitudinal high-frequency electric resistance weld. Uniformly square in cross-section with flat sides, small corner radii and excellent torsional qualities. Available shaft widths are 4, 5 and 6 inches. Anchor base is fabricated from hot-rolled carbon steel plate conforming to ASTM A36, that meets or exceeds a minimum-yield strength of 36,000 psi. Base plate and shaft are circumferentially welded top and bottom. Base cover is finished to match pole. A handhole having nominal dimensions of 3" x 5" for all shafts. Included is a cover with attachment screws. Top cap provided with all drill-mount and open top "PT" poles. Fasteners are high-strength galvanized, zinc-plated or stainless steel. Finish: Must specify finish. Grounding: Provision located immediately inside handhole rim. Grounding hardware is not included (provided by others). Anchor bolts: Top portion of anchor bolt is galvanized per ASTM A-153. Made of steel rod having a minimum yield strength of 55,000 psi. Note: Specifications subject to change without notice. Actual performance may differ as a result of end-user environment and application. Anchor Base Poles SSS SQUARE STRAIGHT STEEL IMPORTANT INSTALLATION NOTES: • Do not erect poles without having fixtures installed. • Factory-supplied templates must be used when setting anchor bolts. Lithonia Lighting will not accept claim for incorrect anchorage placement due to failure to use Lithonia Lighting factory templates. • If poles are stored outside, all protective wrapping must be removed immediately upon delivery to prevent finish damage. • Lithonia Lighting is not responsible for the foundation design. SSS NOTES: 1. PT open top poles include top cap. When ordering tenon mounting and drill mounting for the same pole, follow this example: DM28/ T20. The combination includes a required extra handhole. 2. The drilling template to be used for a particular luminaire depends on the luminaire that is used. Refer to the Technical Data Section of the Outdoor Binder for Drilling Templates. 3. Insert "1" or "2" to designate fixture size; e.g. DM19AST2. 4. Specify location and orientation when ordering option. For 1st "x": Specify the height in feet above base of pole. Example: 5ft = 5 and 20ft = 20 For 2nd "x": Specify orientation from handhole (A,B,C,D) Refer to the Handhole Orientation diagram above. HANDHOLE ORIENTATION A Handhole B C D SSS Series Nominal fixture mounting height Nominal shaft base size/wall thickness Mounting1 Options Finish10 SSS 10 – 39 feet (See back page.) (See back page.)Tenon mounting PT Open top (includes top cap) T20 2-3/8" O.D. (2" NPS) T25 2-7/8" O.D. (2-1/2" NPS) T30 3-1/2" O.D. (3" NPS) T35 4" O.D. (3-1/2" NPS) Drill mounting2 DM19 1 at 90° DM28 2 at 180° DM28 PL 2 at 180° with one side plugged DM29 2 at 90° DM39 3 at 90° DM49 4 at 90° CSX/DSX/AERIS™/OMERO™ Drill mounting2 DM19AS 1 at 90° DM28AS 2 at 180° DM29AS 2 at 90° DM39AS 3 at 90° DM49AS 4 at 90° AERIS™ Suspend drill mounting2, 3 DM19AST_1 at 90° DM28AST_2 at 180° DM29AST_2 at 90° DM39AST_3 at 90° DM49AST_4 at 90° OMERO™ Suspend drill mounting2, 3 DM19MRT_1 at 90° DM28MRT_2 at 180° DM29MRT_2 at 90° DM39MRT_3 at 90° DM49MRT_4 at 90° Shipped installed L/AB Less anchor bolts VD Vibration damper TP Tamper proof H1-18Sxx Horizontal arm bracket (1 fixture)4, 5 FDLxx Festoon outlet less electrical4 CPL12xx 1/2" coupling4 CPL34xx 3/4" coupling4 CPL1xx 1" coupling4 NPL12xx 1/2" threaded nipple4 NPL34xx 3/4" threaded nipple4 NPL1xx 1" threaded nipple4 EHHxx Extra handhole4, 6 MAEX Match existiing 7 USPOM United States point of manufacture8 IC Interior coating9 Standard colors DDB Dark bronze DWH White DBL Black DMB Medium bronze DNA Natural aluminum Classic colors DSS Sandstone DGC Charcoal gray DTG Tennis green DBR Bright red DSB Steel blue Architectural colors (powder finish)10 ORDERING INFORMATION Lead times will vary depending on options selected. Consult with your sales representative. Example: SSS 20 5C DM19 DDB 5. Horizontal arm is 18" x 2-3/8" O.D. tenon standard. 6. Combination of tenon-top and drill mount includes extra handhole. 7. Must add original order number 8. Use when mill certifications are required. 9. Provides enhanced corrosion resistance. 10. Additional colors available; see www.lithonia.com/archcolors or Architectural Colors brochure (Form No. 794.3). Powder finish standard. POLE-SSS OUTDOOR: One Lithonia Way Conyers, GA 30012 Phone: 800-279-8041 Fax: 770-981-1209 www.lithonia.com ©1994-2012 Acuity Brands Lighting, Inc. All rights reserved. Rev. 08/08/12 SSS Square Straight Steel Poles IMPORTANT: • These specifications are intended for general purposes only. Lithonia reserves the right to change material or design, without prior notice, in a continuing effort to upgrade its products. BASE DETAIL 18" A C TECHNICAL INFORMATION EPA (ft2) with 1.3 gust Catalog Number Nominal mount ht. (ft) Pole Shaft Size (in x ft) Wall Thickness (in)Gauge 80 mph Max. weight 90 mph Max. weight 100 mph Max. weight Bolt Circle (in)Bolt Size (in x in x in) Approximate ship (lbs) SSS 10 4C 10 4.0 x 10.0 0.1196 11 30.6 765 23.8 595 18.9 473 8--9 3/4 x 18 x 3 75 SSS 12 4C 12 4.0 x 12.0 0.1196 11 24.4 610 18.8 470 14.8 370 8--9 3/4 x 18 x 3 90 SSS 14 4C 14 4.0 x 14.0 0.1196 11 19.9 498 15.1 378 11.7 293 8--9 3/4 x 18 x 3 100 SSS 16 4C 16 4.0 x 16.0 0.1196 11 15.9 398 11.8 295 8.9 223 8--9 3/4 x 18 x 3 115 SSS 18 4C 18 4.0 x 18.0 0.1196 11 12.6 315 9.2 230 6.7 168 8--9 3/4 x 18 x 3 125 SSS 20 4C 20 4.0 x 20.0 0.1196 11 9.6 240 6.7 167 4.5 150 8--9 3/4 x 18 x 3 140 SSS 20 4G 20 4.0 x 20.0 0.1793 7 14 350 11 275 8 200 8--9 3/4 x 30 x 3 198 SSS 20 5C 20 5.0 x 20.0 0.1196 11 17.7 443 12.7 343 9.4 235 10--12 1 x 36 x 4 185 SSS 20 5G 20 5.0 x 20.0 0.1793 7 28.1 703 21.4 535 16.2 405 10--12 1 x 36 x 4 265 SSS 25 4C 25 4.0 x 25.0 0.1196 11 4.8 150 2.6 100 1 50 8--9 3/4 x 18 x 3 170 SSS 25 4G 25 4.0 x 25.0 0.1793 7 10.8 270 7.7 188 5.4 135 8--9 3/4 x 30 x 3 245 SSS 25 5C 25 5.0 x 25.0 0.1196 11 9.8 245 6.3 157 3.7 150 10--12 1 x 36 x 4 225 SSS 25 5G 25 5.0 x 25.0 0.1793 7 18.5 463 13.3 333 9.5 238 10--12 1 x 36 x 4 360 SSS 30 4G 30 4.0 x 30.0 0.1793 7 6.7 168 4.4 110 2.6 65 8--9 3/4 x 30 x 3 295 SSS 30 5C 30 5.0 x 30.0 0.1196 11 4.7 150 2 50 ----10--12 1 x 36 x 4 265 SSS 30 5G 30 5.0 x 30.0 0.1793 7 10.7 267 6.7 167 3.9 100 10--12 1 x 36 x 4 380 SSS 30 6G 30 6.0 x 30.0 0.1793 7 19 475 13.2 330 9 225 11--13 1 x 36 x 4 520 SSS 35 5G 35 5.0 x 35.0 0.1793 7 5.9 150 2.5 100 ----10--12 1 x 36 x 4 440 SSS 35 6G 35 6.0 x 35.0 0.1793 7 12.4 310 7.6 190 4.2 105 11--13 1 x 36 x 4 540 SSS 39 6G 39 6.0 x 39.0 0.1793 7 7.2 180 3 75 ----11--13 1 x 36 x 4 605 POLE DATA Shaft base size Bolt circle A Bolt projection B Base square C Template description Anchor bolt description Anchor bolt and template number 4"C 8-1/2"2-3/4"–4"8"ABTEMPLATE PJ50004 AB18-0 ABSSS-4C 4"G 8-1/2"2-3/4"–4"8"ABTEMPLATE PJ50004 AB30-0 ABSSS-4G 5"10"–12"3-3/8"–4"11"ABTEMPLATE PJ50010 AB36-0 ABSSS-5 6"11"–13"3-3/8"–4"12-1/2"ABTEMPLATE PJ50011 AB36-0 N/A