HomeMy WebLinkAbout08332.pdfBICKFORD OF CARMEL, IN 12/12/2012
ROLLING COUNTER DOOR 08332 - 1
SECTION 08332 – ROLLING COUNTER DOORS
PART 1 GENERAL
1.1 SUMMARY
A. This section includes rolling counter doors consisting of the following:
1. Overhead Coiling Counter Doors, manually operated.
1.2 RELATED SECTIONS
A. Section 05500 - Metal Fabrications: Support framing and framed opening.
B. Section 06402 - Finish Carpentry: Wood jamb and head trim.
C. Section 08710 - Door Hardware: Product Requirements for cylinder core and keys.
D. Section 09900 - Painting: Field applied finish.
1.3 REFERENCES
A. ASTM A 653 - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron
Alloy-Coated (Galvannealed) by the Hot-Dip Process.
B. ASTM A 924 - Standard Specification for General Requirements for Steel Sheet, Metallic-
Coated by the Hot-Dip Process.
C. ASTM B 221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars,
Rods, Wire, Profiles, and Tubes.
D. ASTM B 221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars,
Rods, Wire, Profiles, and Tubes (Metric).
1.4 SUBMITTALS
A. Submit under provisions of Section 01300.
B. Product Data: Manufacturer's data sheets on each product to be used, including:
1. Preparation instructions and recommendations.
2. Storage and handling requirements and recommendations.
3. Details of construction and fabrication.
ROLLING COUNTER DOORS 04810 - 2
4. Installation methods.
C. Shop Drawings: Include detailed plans, elevations, details of framing members, required
clearances, anchors, and accessories. Include relationship with adjacent construction.
D. Selection Samples: For each finish product specified, two complete sets of color chips
representing manufacturer's full range of available colors and patterns.
E. Verification Samples: For each finish product specified, two samples, minimum size 6
inches (150 mm) long, representing actual product, color, and patterns.
F. Manufacturer's Certificates: Certify products meet or exceed specified requirements.
1.5 QUALITY ASSURANCE
A. Manufacturer Qualifications: Company specializing in performing Work of this section with a
minimum of five years experience in the fabrication and installation of security closures.
B. Installer Qualifications: Company specializing in performing Work of this section with
minimum three years and approved by manufacturer.
C. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and
application workmanship.
1. Install in areas designated by Architect.
2. Do not proceed with remaining work until workmanship and installation is approved by
Architect.
3. Refinish mock-up area as required to produce acceptable work.
1.6 DELIVERY, STORAGE, AND HANDLING
A. Store products in manufacturer's unopened packaging until ready for installation.
B. Protect materials from exposure to moisture. Do not deliver until after wet work is complete
and dry.
C. Store materials in a dry, warm, ventilated weathertight location.
1.7 PROJECT CONDITIONS
A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits
recommended by manufacturer for optimum results. Do not install products under
environmental conditions outside manufacturer's absolute limits.
1.8 COORDINATION
ROLLING COUNTER DOORS 04810 - 3
A. Coordinate Work with other operations and installation of adjacent finish materials to avoid
damage to installed materials.
PART 2 PRODUCTS
2.1 MANUFACTURERS
A. Available Manufacturers: Subject to compliance with requirements, manufacturers offering
products that may be incorporated into the Work include, but are not limited to,
manufacturers specified
1. Overhead Door Corp., 2501 S. State Hwy. 121, Suite 200, Lewisville, TX 75067.
ASD. Tel. Toll Free: (800) 275-3290. Phone: (469) 549-7100. Fax: (972) 906-
1499. Web Site: www.overheaddoor.com. E-mail: info@overheaddoor.com
2.2 OVERHEAD COILING WOOD COUNTER DOORS
A. Wood Counter Doors with Integral Frame: Overhead Door Corporation, Series 665.
1. Curtain: Interlocking wood slats, 1-5/8 inch (41 mm) high by 1/2 inch (12.5 mm) thick.
Bottom bar shall have flush lift handles.
2. Slat Material and Finish:
a. Birch without finish, to be finished on site by others.
b. Finish: Stain to match cabinets, doors and trim.
3. Guides:
a. Aluminum guides.
4. Brackets: Galvanized steel to support counterbalance, curtain and hood.
5. Counterbalance: Helical torsion spring type housed in a steel tube or pipe barrel,
supporting the curtain with deflection limited to 0.03 inch (0.8 mm) per foot of span.
Counterbalance shall be adjustable by means of an adjusting tension wheel.
6. Hood: Provide intermediate support brackets as required. Hood fabricated of:
a. Steel prime painted.
7. Operation:
a. Crank operation.
8. Locking:
a. Thumb turn locks.
9. Wall Mounting Condition:
a. Face-of-wall mounting.
PART 3 EXECUTION
ROLLING COUNTER DOORS 04810 - 4
3.1 EXAMINATION
A. Verify opening sizes, tolerances and conditions are acceptable.
B. Examine conditions of substrates, supports, and other conditions under which this work is to
be performed.
C. If substrate preparation is the responsibility of another installer, notify Architect of
unsatisfactory preparation before proceeding.
3.2 PREPARATION
A. Clean surfaces thoroughly prior to installation.
B. Prepare surfaces using the methods recommended by the manufacturer for achieving the
best result for the substrate under the project conditions.
3.3 INSTALLATION
A. Install in accordance with manufacturer's instructions.
B. Use anchorage devices to securely fasten assembly to wall construction and building
framing without distortion or stress.
C. Securely and rigidly brace components suspended from structure. Secure guides to
structural members only.
D. Fit and align assembly including hardware; level and plumb, to provide smooth operation.
E. Coordinate installation of electrical service with Section 16150. Complete wiring from
disconnect to unit components.
F. Coordinate installation of sealants and backing materials at frame perimeter as specified in
Section 07900.
G. Install perimeter trim and closures.
3.4 ADJUSTING
A. Test for proper operation and adjust as necessary to provide proper operation without
binding or distortion.
B. Adjust hardware and operating assemblies for smooth and noiseless operation.
3.5 CLEANING
ROLLING COUNTER DOORS 04810 - 5
A. Clean curtain and components using non-abrasive materials and methods recommended by
manufacturer.
B. Remove labels and visible markings.
C. Touch-up, repair or replace damaged products before Substantial Completion.
3.6 PROTECTION
A. Protect installed products until completion of project.
END OF SECTION 08332